Advertisement
Quick Links
D1918H
LED MONITOR No.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a
product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could result in
serious injury or death.
1
Advertisement
Related Manuals for Dell D1918H
Summary of Contents for Dell D1918H
- Page 1 D1918H LED MONITOR No. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt with in this service information by anyone else could result in...
- Page 2 Assembly and Disassembly Procedures Assembly—SOP D1918H Assembly procedures Preparation before assembly 1. clean the room for work 2. Identify the area for material 3. Prepare the implement, equipments, materials as bellow: 1) Press Fixture 2) Work ing table 3) Screw-Driver...
- Page 3 Step3 1. Stick the K/B FFC cable on the M/B Step4 1. Isolation hood positioning 2.Chapaixian LVDS Step5 1.Aluminum foil and anti-static adhesive tape...
- Page 4 Step6 1. Lock the hexagonal screws Step7 1.Assembly the back cover into the panel Step8 1.Assembly the back cover by locking 1 screws(M3*8)
- Page 5 Step9 Assembling stand Disassembly—SOP D1918H Disassembly procedures Preparation before disassembly 4. clean the room for work 5. Identify the area for material 6. Check the position that the monitors be placed and the quantify of the monitor ;prepare the area for material flow,according to the actual condition plan the disassemble layout 7.
- Page 6 Step2 Remove rear cabinet screw Step3 Disassemble CABI Back...
- Page 7 Step4 1. Take off the AL SHIELDING TAPES and pull out the LVDS cable 2. Remove the press button in the front K/B...
- Page 8 Step5 Unlock the screws Step6 1. Disassemble the K/B and pull out the FFC cable Step7 Unlock the screws and take out the M/B Foam demolition...
- Page 9 Step8 Pull out the LVDS cable Assembly SOP for BOEA185WX3 321171850551001 (MNT) Assembly procedures Preparation before assembly 8. Cleanroom and working table 9. Clean cothes 10. Glove Step 1 1.Take the black on the assembly line 2.Stick the glue in the red box...
- Page 10 Step 2 1.Stick the label on the red box Step 3 1.Stick the block gine on the red box...
- Page 11 Step 4 1.Tear off the glue from the LED light bar 2.Install the LED light bar Step 5 1.Take the reflector plate into the back Step 6 1.Stick the protective film from the light guide plate 2.Take the light guide plate into the back...
- Page 12 Step 7 Take the product on the workbench Tear off the protective film from the light gudie plate 3.Check for bad appearance of light guide plate 4.Take the membrane on the light gudie plate 5.Pay to the rubber frame on the back...
- Page 13 Step 8 1. From the glass on the underside to tear protective film 2.Put the cell in the plastic box Step 9 1. From the upper to tear protective film on the glass Step 10 1.Paste the conductive buiter on the back 2.Paste the conductive buiter on the cell Step 11...
- Page 14 1.Check the iron box appearance 2.Install the iron box to the product Step 12 1.Tear off the release paper from the red box 2.Set up the PCB Step 13 1.Stick the block gine on the red box...
- Page 15 Step 14 Tear off the release paper Stick the black rust on the blackborad Disassembly SOP for BOEA185WX3 321171850551001 (MNT) Assembly procedures Preparation before assembly 11. Cleanroom and working table 12. Clean cothes 13. Glove Step 1 Take the product on the assembly Tear off the black rust from the blackborad...
- Page 16 Step 2 1.Tear the block gine from the red box Step 3 1.Take apart the PCB Step 4 1.Turn the product 2.Take apart the iron box...
- Page 17 Step 5 1.Tear off the conductive buiter from the back 2.Tear off the conductive buiter from the cell 02/28/2017...
- Page 18 Step 6 1.Take apart the cell out of the backt Step 7 1.Take the membrane out of the light gudie plate 02/28/2017...
- Page 19 Step 8 1.Take the light guide plate out of the back Step 9 1.Take the reflector plate out of the back Step 10 02/28/2017...
- Page 20 1.Take the LED light bar out of the back Step 11 1.Tear off the block gine from the red box 02/28/2017...
- Page 21 Step 12 1.Tear off the glue from the red box 02/28/2017...