Page 1 Digital Energy F60 Feeder Protection System UR Series Instruction Manual F60 Revision: 7.1x Manual P/N: 1601-0093-Z2 (GEK-119517A) 832762A2.CDR E83849 GE Digital Energy LISTED 650 Markland Street IND.CONT. EQ. 52TL Markham, Ontario GE Multilin's Quality Management Canada L6C 0M1 System is registered to ISO...
Page 2 The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice.
Page 3: Table Of Contents
1.3 ENERVISTA UR SETUP SOFTWARE 1.3.1 PC REQUIREMENTS ..................1-6 1.3.2 INSTALLATION....................1-6 1.3.3 CONFIGURING THE F60 FOR SOFTWARE ACCESS ........1-7 1.3.4 USING THE QUICK CONNECT FEATURE............. 1-10 1.3.5 CONNECTING TO THE F60 RELAY ............... 1-15 1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD ... 1-16 1.4 UR HARDWARE...
Page 4 USER-PROGRAMMABLE SELF-TESTS ............5-71 5.2.13 CONTROL PUSHBUTTONS ................5-73 5.2.14 USER-PROGRAMMABLE PUSHBUTTONS............5-75 5.2.15 FLEX STATE PARAMETERS ................5-80 5.2.16 USER-DEFINABLE DISPLAYS ................5-81 5.2.17 DIRECT INPUTS/OUTPUTS ................5-83 5.2.18 TELEPROTECTION ..................5-91 5.2.19 INSTALLATION ....................5-91 5.3 REMOTE RESOURCES 5.3.1 REMOTE RESOURCES CONFIGURATION............5-93 F60 Feeder Protection System GE Multilin...
Page 5 IEC 61850 GOOSE INTEGERS..............5-280 5.9 TRANSDUCER INPUTS AND OUTPUTS 5.9.1 DCMA INPUTS ....................5-281 5.9.2 RTD INPUTS....................5-282 5.9.3 DCMA OUTPUTS ..................5-284 5.10 TESTING 5.10.1 TEST MODE ....................5-287 5.10.2 FORCE CONTACT INPUTS ................5-288 GE Multilin F60 Feeder Protection System...
Page 6 MODEL INFORMATION ...................6-30 6.5.2 FIRMWARE REVISIONS..................6-30 7. COMMANDS AND 7.1 COMMANDS TARGETS 7.1.1 COMMANDS MENU ...................7-1 7.1.2 VIRTUAL INPUTS ....................7-1 7.1.3 CLEAR RECORDS .....................7-2 7.1.4 SET DATE AND TIME ..................7-2 7.1.5 RELAY MAINTENANCE ..................7-3 F60 Feeder Protection System GE Multilin...
Page 7 READ ACTUAL VALUES OR SETTINGS (FUNCTION CODE 03/04H) ...B-3 B.2.3 EXECUTE OPERATION (FUNCTION CODE 05H) ...........B-4 B.2.4 STORE SINGLE SETTING (FUNCTION CODE 06H) ........B-4 B.2.5 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H) ........B-5 B.2.6 EXCEPTION RESPONSES ................B-5 GE Multilin F60 Feeder Protection System...
Page 8 LOGICAL NODES TABLE ................C-26 D. IEC 60870-5-104 D.1 IEC 60870-5-104 COMMUNICATIONS D.1.1 INTEROPERABILITY DOCUMENT..............D-1 D.1.2 IEC 60870-5-104 POINT LIST ................D-9 E. DNP COMMUNICATIONS E.1 DEVICE PROFILE DOCUMENT E.1.1 DNP V3.00 DEVICE PROFILE ................E-1 viii F60 Feeder Protection System GE Multilin...
Page 9 F.1 RADIUS SERVER CONFIGURATION F.1.1 RADIUS SERVER CONFIGURATION............... F-1 G. MISCELLANEOUS G.1 CHANGE NOTES G.1.1 REVISION HISTORY ..................G-1 G.1.2 CHANGES TO THE F60 MANUAL ..............G-2 G.2 ABBREVIATIONS G.2.1 STANDARD ABBREVIATIONS ................ G-5 G.3 WARRANTY G.3.1 GE MULTILIN WARRANTY ................G-7 INDEX...
Page 10 TABLE OF CONTENTS F60 Feeder Protection System GE Multilin...
Page 11: Getting Started
1.1 IMPORTANT PROCEDURES 1 GETTING STARTED 1.1IMPORTANT PROCEDURES Use this chapter for initial setup of your new F60 Feeder Protection System. 1.1.1 CAUTIONS AND WARNINGS Before attempting to install or use the device, review all safety indicators in this document to help prevent injury, equipment damage, or downtime.
Page 12: Inspection Procedure
• GE EnerVista™ CD (includes the EnerVista UR Setup software and manuals in PDF format) • Mounting screws If there is any noticeable physical damage, or any of the contents listed are missing, please contact GE Digital Energy immediately as follows.
Page 13: Ur Overview
1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR The GE Universal Relay (UR) series is a new generation of digital, modular, and multifunction equipment that is easily incorporated into automation systems, at both the station and enterprise levels. 1.2.2 HARDWARE ARCHITECTURE...
Page 14 The UR-series devices operate in a cyclic scan fashion. The device reads the inputs into an input status table, solves the logic program (FlexLogic equation), and then sets each output to the appropriate state in an output status table. Any result- ing task execution is priority interrupt-driven. Figure 1–3: UR-SERIES SCAN OPERATION F60 Feeder Protection System GE Multilin...
Page 15: Software Architecture
Employing OOD/OOP in the software architecture of the F60 achieves the same features as the hardware architecture: modularity, scalability, and flexibility. The application software for any UR-series device (for example, feeder protection, transformer protection, distance protection) is constructed by combining objects from the various functional classes.
Page 16: Enervista Ur Setup Software
500 MB free hard drive space (1 GB recommended) • 1024 x 768 display (1280 x 800 recommended) The following qualified modems have been tested to be compliant with the F60 and the EnerVista UR Setup software: • US Robotics external 56K FaxModem 5686 •...
Page 17: Configuring The F60 For Software Access
An Ethernet module must be specified at the time of ordering. • To configure the F60 for local access with a laptop through either the front RS232 port or rear Ethernet port, see the Using the Quick Connect Feature section.
Page 18 SERIAL PORTS 10. Click the Read Order Code button to connect to the F60 device and upload the order code. If a communications error occurs, ensure that the EnerVista UR Setup serial communications values entered in the previous step correspond to the relay setting values.
Page 19 MODBUS PROTOCOL 21. Click the Read Order Code button to connect to the F60 device and upload the order code. If an communications error occurs, ensure that the three EnerVista UR Setup values entered in the previous steps correspond to the relay setting values.
Page 20: Using The Quick Connect Feature
USING QUICK CONNECT VIA THE REAR ETHERNET PORTS To use the Quick Connect feature to access the F60 from a computer through Ethernet, first assign an IP address to the relay from the front panel keyboard. Press the MENU key until the SETTINGS menu displays.
Page 21 Right-click the Local Area Connection icon and select Properties. Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button. Click the “Use the following IP address” box. GE Multilin F60 Feeder Protection System 1-11...
Page 22 1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED Enter an IP address with the first three numbers the same as the IP address of the F60 relay and the last number dif- ferent (in this example, 1.1.1.2). Enter a subnet mask equal to the one set in the F60 (in this example, 255.0.0.0).
Page 23 Ensure that the “Use a proxy server for your LAN” box is not checked. If this computer is used to connect to the Internet, re-enable any proxy server settings after the laptop has been discon- nected from the F60 relay. Start the Internet Explorer software.
Page 24 Click the Quick Connect button to open the Quick Connect dialog box. Select the Ethernet interface and enter the IP address assigned to the F60, then click the Connect button. The EnerV- ista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick Con- nect”...
Page 25: Connecting To The F60 Relay
The EnerVista UR Setup software has several quick action buttons to provide instant access to several functions that are often performed when using F60 relays. From the online window, users can select the relay to interrogate from a pull-down window, then click the button for the action they want to perform. The following quick action functions are available: •...
Page 26: Setting Up Cybersentry And Changing Default Password
. Be sure to disable this bypass setting after SETTINGS > PRODUCT SETUP > SECURITY > SUPERVISORY commissioning the device. You can change the password for any role either from the front panel or through EnerVista. 1-16 F60 Feeder Protection System GE Multilin...
Page 27 If using EnerVista, navigate to Settings > Product Setup > Security. Change the Local Administrator Password, for example. It is strongly recommended that the password for the Administrator be changed from the default. Changing the passwords for the other three roles is optional. Figure 1–11: CHANGING THE DEFAULT PASSWORD GE Multilin F60 Feeder Protection System 1-17...
Page 28: Ur Hardware
This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the F60 rear communications port. The converter terminals (+, –, GND) are connected to the F60 communication module (+, –, COM) terminals. See the CPU communica- tions ports section in chapter 3 for details.
Page 29: Using The Relay
To put the relay in the “Programmed” state, press either of the VALUE keys once and then press ENTER. The face- plate Trouble LED turns off and the In Service LED turns on. GE Multilin F60 Feeder Protection System 1-19...
Page 30: Relay Passwords
For more information, see the CyberSentry content in the Security section of the next chapter. 1.5.6 FLEXLOGIC CUSTOMIZATION FlexLogic equation editing is required for setting user-defined logic for customizing the relay operations. See the FlexLogic section in Chapter 5. 1-20 F60 Feeder Protection System GE Multilin...
Page 31: Commissioning
As such, no further functional tests are required. The F60 performs a number of continual self-tests and takes the necessary action in case of any major errors (see the Relay Self-tests section in chapter 7). However, it is recommended that F60 maintenance be scheduled with other system maintenance.
Page 32 1.5 USING THE RELAY 1 GETTING STARTED 1-22 F60 Feeder Protection System GE Multilin...
Page 33: Product Description
TFTP protocols, PTP (according to IEEE Std. 1588-2008 or IEC 61588), and allows access to the relay via any stan- dard web browser (F60 web pages). The IEC 60870-5-104 protocol is supported on the Ethernet port, and DNP 3.0 and IEC 60870-5-104 cannot be enabled at the same time.
Page 34: Security
EnerVista software. • CyberSentry security — Advanced security options available as a software option. When purchased, the options are automatically enabled, and the default Password security and EnerVista security are disabled. F60 Feeder Protection System GE Multilin...
Page 35 When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password applies.
Page 36 When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication database to authenticate the user. No password or security information are displayed in plain text by the EnerVista software or UR device, nor are they ever transmitted without cryptographic protection. F60 Feeder Protection System GE Multilin...
Page 37 |------------ System Setup |------------ FlexLogic |------------ Grouped Elements |------------ Control Elements |------------ Inputs / Outputs |--------------- Contact Input Contact Input thresh- |--------------- |--------------- Virtual Inputs |--------------- Contact Output |--------------- Virtual Output |--------------- Remote Devices GE Multilin F60 Feeder Protection System...
Page 38 RW = read and write access R = read access Supervisor = RW (default), Administrator = R (default), Administrator = RW (only if Supervisor role is disabled) NA = the permission is not enforced by CyberSentry Security F60 Feeder Protection System GE Multilin...
Page 39 RADIUS server when one is provided. If a RADIUS server is provided, but is unreachable over the network, server authentication requests are denied. In this situ- ation, use local UR accounts to gain access to the UR system. GE Multilin F60 Feeder Protection System...
Page 40: Ordering
2.1.3 ORDERING a) OVERVIEW The F60 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following mod- ules: power supply, CPU, CT/VT, digital input and output, transducer input and output, and inter-relay communications.
Page 41 RS422, 1 Channel RS422, 2 Channels The order codes for the reduced size vertical mount units are shown below. Table 2–5: F60 ORDER CODES (REDUCED SIZE VERTICAL UNITS) * - F Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 42 * This CPU module type cannot be ordered with 8Z module c) ORDER CODES WITH PROCESS BUS MODULES The order codes for the horizontal mount units with the process bus module are shown below. Table 2–6: F60 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS) * - F - W/X...
Page 43 2 PRODUCT DESCRIPTION 2.1 INTRODUCTION Table 2–6: F60 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS) PRP, IEC 61850, and PMU IEEE 1588 and CyberSentry Lvl 1 IEEE 1588 and CyberSentry Lvl 1 and Ethernet Global Data (EGD) IEEE 1588 and CyberSentry Lvl 1 and IEC 61850...
Page 44 2.1 INTRODUCTION 2 PRODUCT DESCRIPTION Table 2–7: F60 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS) * - F Reduced Size Vertical Mount (see note regarding P/R slot below) BASE UNIT Base Unit RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
Page 45 2 PRODUCT DESCRIPTION 2.1 INTRODUCTION Table 2–7: F60 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS) Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER Channel 1 - G.703;...
Page 46: Replacement Modules
Replacement modules can be ordered separately. When ordering a replacement CPU module or faceplate, provide the serial number of your existing unit. Not all replacement modules may be applicable to the F60 relay. Only the modules specified in the order codes are available as replacement modules.
Page 47 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed) 4 dcmA inputs, 4 RTD inputs 8 dcmA inputs * CPU module types 8L and 8N cannot be ordered with the 8Z module GE Multilin F60 Feeder Protection System 2-15...
Page 48: Specifications
0.1 to 2.0  CT: ±0.5% of reading or ±0.4% of rated Inverse; IEC (and BS) A/B/C and Short (whichever is greater) Inverse; GE IAC Inverse, Short/Very/ for > 2.0  CT: ±1.5% of reading > 2.0  CT rating Extremely Inverse; I t;...
Page 49 ±0.5% of reading from 10 to 208 V 0.00 to 250.00  in steps of 0.01 Offset impedance: Curve shapes: GE IAV Inverse, Definite Time Pickup level: 0.015 to 30.000 pu in steps of 0.01 Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01...
Page 50 <42 ms at 1.10  pickup at 60 Hz Operate time: Operate time: typically 4 cycles at 0.1 Hz/s change typically 3.5 cycles at 0.3 Hz/s change typically 3 cycles at 0.5 Hz/s change 2-18 F60 Feeder Protection System GE Multilin...
Page 51: User-Programmable Elements
Pickup & dropout delay: 0.000 to 65.535 s in steps of 0.001 Reset points: 40 (0 through 1 of pickup) Operate points: 80 (1 through 20 of pickup) Time delay: 0 to 65535 ms in steps of 1 GE Multilin F60 Feeder Protection System 2-19...
Page 52: Monitoring
01 channel for NN days Triggers: any element pickup, dropout, or operate; 16 channels for NN days digital input change of state; digital out- put change of state; self-test events Data storage: in non-volatile memory 2-20 F60 Feeder Protection System GE Multilin...
Page 53: Metering
< 0.4pu: as above plus %error of f THD: 1. f > 0.4pu: (0.25% + 0.035% / harmonic) of reading or 0.20% of 100%, whichever is greater 2. f < 0.4pu: as above plus %error of f GE Multilin F60 Feeder Protection System 2-21...
Page 54: Inputs
Default states on loss of comms.: On, Off, Latest/Off, Latest/On Recognition time: < 1 ms Remote DPS inputs: Debounce time: 0.0 to 16.0 ms in steps of 0.5 Continuous current draw:3 mA (when energized) 2-22 F60 Feeder Protection System GE Multilin...
Page 55: Power Supply
Control mode: operate-dominant or reset-dominant FORM-A VOLTAGE MONITOR Applicable voltage: approx. 15 to 250 V DC Trickle current: approx. 1 to 2.5 mA FORM-A CURRENT MONITOR Threshold current: approx. 80 to 100 mA GE Multilin F60 Feeder Protection System 2-23...
Page 56 99% Settling time to a step change: 100 ms Isolation: 1.5 kV Driving signal: any FlexAnalog quantity Upper and lower limit for the driving signal: –90 to 90 pu in steps of 0.001 2-24 F60 Feeder Protection System GE Multilin...
Page 57: Communications
1300 nm Laser, –1 dBm –30 dBm 29 dB Singlemode 1550 nm Laser, +5 dBm –30 dBm 35 dB Singlemode These power budgets are calculated from the manu- facturer’s worst-case transmitter power and worst NOTE GE Multilin F60 Feeder Protection System 2-25...
Page 58: Environmental
Pollution degree: impaired at temperatures less than – Overvoltage category: 20°C Ingress protection: IP20 front, IP10 back HUMIDITY Humidity: operating up to 95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6 days). 2-26 F60 Feeder Protection System GE Multilin...
Page 59: Type Tests
20 V/m, 80 MHz to 1 GHz Safety UL508 e83849 NKCR Safety UL C22.2-14 e83849 NKCR7 Safety UL1053 e83849 NKCR 2.2.12 PRODUCTION TESTS THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. GE Multilin F60 Feeder Protection System 2-27...
Page 60: Approvals
To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. 2-28 F60 Feeder Protection System GE Multilin...
Page 61: Hardware
HORIZONTAL UNITS The F60 Feeder Protection System is available as a 19-inch rack horizontal mount unit with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains addi- tional user-programmable pushbuttons and LED indicators.
Page 62 VERTICAL UNITS The F60 Feeder Protection System is available as a reduced size (¾) vertical mount unit, with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains addi- tional user-programmable pushbuttons and LED indicators.
Page 63 RS232 communications port. The relay is secured to the panel with the use of four screws supplied with the relay. 11.015” 7.482” 1.329” 13.560” 15.000” 14.025” 4.000” 9.780” 843809A1.CDR Figure 3–4: F60 VERTICAL DIMENSIONS (ENHANCED PANEL) GE Multilin F60 Feeder Protection System...
Page 64 3.1 DESCRIPTION 3 HARDWARE Figure 3–5: F60 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL) For details on side mounting F60 devices with the enhanced front panel, refer to the following documents available online from the GE Multilin website. • GEK-113180: UR-series UR-V side-mounting front panel assembly instructions.
Page 65 3 HARDWARE 3.1 DESCRIPTION Figure 3–6: F60 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL) GE Multilin F60 Feeder Protection System...
Page 66: Rear Terminal Layout
3.1 DESCRIPTION 3 HARDWARE Figure 3–7: F60 VERTICAL SIDE MOUNTING REAR DIMENSIONS (STANDARD PANEL) 3.1.2 REAR TERMINAL LAYOUT Figure 3–8: REAR TERMINAL VIEW F60 Feeder Protection System GE Multilin...
Page 67 (nearest to CPU module) which is indicated by an arrow marker on the terminal block. See the following figure for an example of rear terminal assignments. Figure 3–9: EXAMPLE OF MODULES IN F AND H SLOTS GE Multilin F60 Feeder Protection System...
Page 68: Wiring
3.2 WIRING 3 HARDWARE 3.2WIRING 3.2.1 TYPICAL WIRING Figure 3–10: TYPICAL WIRING DIAGRAM (T MODULE SHOWN FOR CPU) F60 Feeder Protection System GE Multilin...
Page 69 3 HARDWARE 3.2 WIRING Figure 3–11: TYPICAL WIRING DIAGRAM WITH HIGH-IMPEDANCE DETECTION (T MODULE SHOWN FOR CPU) GE Multilin F60 Feeder Protection System...
Page 70: Dielectric Strength
(see the Self-test errors section in chapter 7) or control power is lost, the relay is de-energize. For high reliability systems, the F60 has a redundant option in which two F60 power supplies are placed in parallel on the bus.
Page 71: Ct And Vt Modules
CT connections for both ABC and ACB phase rotations are identical as shown in the Typical wiring diagram. The exact placement of a zero-sequence core balance CT to detect ground fault current is shown below. Twisted-pair cabling on the zero-sequence CT is recommended. GE Multilin F60 Feeder Protection System 3-11...
Page 72 8F and 8G modules (4 CTs and 4 VTs) Current inputs 8H and 8J modules (8 CTs) Current inputs Not used 8Z module (used for high-impedance fault detection) 842769A1.CDR Figure 3–14: CT/VT MODULE WIRING 3-12 F60 Feeder Protection System GE Multilin...
Page 73: Process Bus Modules
3.2.5 PROCESS BUS MODULES The F60 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin HardFiber system, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber merging units, known as Bricks.
Page 74: Contact Inputs And Outputs
The terminal configuration for contact inputs is different for the two applications. The contact inputs are grouped with a common return. The F60 has two versions of grouping: four inputs per common return and two inputs per common return. When a contact input/output module is ordered, four inputs per common is used.
Page 75 ~6a, ~6c 2 Inputs Form-A ~7a, ~7c 2 Inputs Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~8a, ~8c 2 Inputs Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs GE Multilin F60 Feeder Protection System 3-15...
Page 76 Not Used ~5a, ~5c 2 Inputs 2 Outputs Solid-State Solid-State ~6a, ~6c 2 Inputs 2 Outputs Not Used Not Used ~7a, ~7c 2 Inputs 2 Outputs Solid-State Solid-State ~8a, ~8c 2 Inputs Not Used 3-16 F60 Feeder Protection System GE Multilin...
Page 77 3 HARDWARE 3.2 WIRING Figure 3–17: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2) GE Multilin F60 Feeder Protection System 3-17...
Page 78 CONTACT IN CONTACT IN COMMON SURGE 842763A2.CDR Figure 3–18: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2) For proper functionality, observe correct polarity for all contact input and solid state output connec- tions. 3-18 F60 Feeder Protection System GE Multilin...
Page 79 There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recom- mend using an external DC supply. NOTE GE Multilin F60 Feeder Protection System 3-19...
Page 80 CONTACT INPUT 2 AUTO-BURNISH = OFF CONTACT INPUT 1 AUTO-BURNISH = OFF CONTACT INPUT 2 AUTO-BURNISH = ON CONTACT INPUT 1 AUTO-BURNISH = ON CONTACT INPUT 2 AUTO-BURNISH = ON 842751A1.CDR Figure 3–21: AUTO-BURNISH DIP SWITCHES 3-20 F60 Feeder Protection System GE Multilin...
Page 81 3 HARDWARE 3.2 WIRING The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the auto- burnish functionality using an oscilloscope. NOTE GE Multilin F60 Feeder Protection System 3-21...
Page 82: Transducer Inputs/Outputs
(5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay. Wherever a tilde “~” symbol appears, substitute with the slot position of the module. NOTE Figure 3–22: TRANSDUCER INPUT/OUTPUT MODULE WIRING 3-22 F60 Feeder Protection System GE Multilin...
Page 83: Rs232 Faceplate Port
3.2.8 RS232 FACEPLATE PORT A 9-pin RS232C serial port is located on the F60 faceplate for programming with a computer. All that is required to use this interface is a computer running the EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is shown in the following figure for both 9-pin and 25-pin connectors.
Page 84 This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the F60 COM terminal (#3); others function cor- rectly only if the common wire is connected to the F60 COM terminal, but insulated from the shield.
Page 85 62.5 µm for 100 Mbps. For optical power budgeting, splices are required every 1 km for the transmitter/receiver pair. When splicing optical fibers, the diameter and numerical aperture of each fiber must be the same. GE Multilin F60 Feeder Protection System 3-25...
Page 86: Irig-B
Figure 3–26: OPTIONS FOR THE IRIG-B CONNECTION Using an amplitude modulated receiver causes errors up to 1 ms in event time-stamping. NOTE 3-26 F60 Feeder Protection System GE Multilin...
Page 87: Direct Input/Output Communications
3.3DIRECT INPUT/OUTPUT COMMUNICATIONS 3.3.1 DESCRIPTION The F60 direct inputs and outputs feature makes use of the type 7 series of communications modules, which allow direct messaging between devices. The communications channels are normally connected in a ring configuration as shown in the following figure. The trans- mitter of one module is connected to the receiver of the next module.
Page 88 These modules are listed in the following table. All fiber modules use ST type connectors. Not all the direct input and output communications modules may be applicable to the F60 relay. Only the modules specified in the order codes are available as direct input and output communications modules.
Page 89: Fiber: Led And Eled Transmitters
The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser module. Figure 3–31: LASER FIBER MODULES When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver. GE Multilin F60 Feeder Protection System 3-29...
Page 90: Interface
Remove the top cover by sliding it towards the rear and then lift it upwards. Set the timing selection switches (channel 1, channel 2) to the desired timing modes. Replace the top cover and the cover screw. 3-30 F60 Feeder Protection System GE Multilin...
Page 91 For connection to a higher order system (UR- to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). GE Multilin F60 Feeder Protection System 3-31...
Page 92 G.703 line side of the interface while the other lies on the differential Manchester side of the interface. DMR = Differential Manchester Receiver DMX = Differential Manchester Transmitter G7X = G.703 Transmitter G7R = G.703 Receiver 842775A1.CDR Figure 3–36: G.703 DUAL LOOPBACK MODE 3-32 F60 Feeder Protection System GE Multilin...
Page 93: Rs422 Interface
UR–RS422 channels is synchronized via the send timing leads on data module 1 as shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a viable option that does not impose timing restrictions. GE Multilin F60 Feeder Protection System 3-33...
Page 94 Figure 3–39: TIMING CONFIGURATION FOR RS422 TWO-CHANNEL, THREE-TERMINAL APPLICATION Data module 1 provides timing to the F60 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure above since they vary by manufacturer.
Page 95: Rs422 And Fiber Interface
G.703 and fiber interfaces. When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver. GE Multilin F60 Feeder Protection System 3-35...
Page 96: Ieee C37.94 Interface
Connection: as per all fiber optic connections, a Tx to Rx connection is required The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94 standard as shown below. 3-36 F60 Feeder Protection System GE Multilin...
Page 97 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted. GE Multilin F60 Feeder Protection System 3-37...
Page 98 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE Figure 3–43: IEEE C37.94 TIMING SELECTION SWITCH SETTING 3-38 F60 Feeder Protection System GE Multilin...
Page 99 Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit" • Solid red — FPGA is not receiving a valid packet or the packet received is invalid GE Multilin F60 Feeder Protection System 3-39...
Page 100: C37.94Sm Interface
For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured. 3-40 F60 Feeder Protection System GE Multilin...
Page 101 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted. Figure 3–45: C37.94SM TIMING SELECTION SWITCH SETTING GE Multilin F60 Feeder Protection System 3-41...
Page 102 Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit" • Solid red — FPGA is not receiving a valid packet or the packet received is invalid 3-42 F60 Feeder Protection System GE Multilin...
Page 103: Human Interfaces
In online mode, you can communicate with the device in real-time. The EnerVista UR Setup software is provided with every F60 relay and runs on Microsoft Windows XP, 7, and Server 2008. This chapter provides a summary of the basic EnerVista UR Setup software interface features. The EnerVista UR Setup Help File provides details for getting started and using the EnerVista UR Setup software interface.
Page 104 Site List window are automatically sent to the online communicating device. g) FIRMWARE UPGRADES The firmware of a F60 device can be upgraded, locally or remotely, via the EnerVista UR Setup software. The correspond- ing instructions are provided by the EnerVista UR Setup Help file under the topic “Upgrading Firmware”.
Page 105: Enervista Ur Setup Main Window
4.1.5 SETTINGS TEMPLATES Setting file templates simplify the configuration and commissioning of multiple relays that protect similar assets. An exam- ple of this is a substation that has ten similar feeders protected by ten UR-series F60 relays. GE Multilin F60 Feeder Protection System...
Page 106 Select the Template Mode > Edit Template option to place the device in template editing mode. Enter the template password then click OK. Open the relevant settings windows that contain settings to be specified as viewable. F60 Feeder Protection System GE Multilin...
Page 107 The following procedure describes how to add password protection to a settings file template. Select a settings file from the offline window on the left of the EnerVista UR Setup main screen. Selecting the Template Mode > Password Protect Template option. GE Multilin F60 Feeder Protection System...
Page 108 Template Mode > View In Template Mode command. The template specifies that only the Pickup Curve Phase time overcurrent settings window without template applied. settings be available. 842858A1.CDR Figure 4–4: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE COMMAND F60 Feeder Protection System GE Multilin...
Page 109 Select an installed device or settings file from the tree menu on the left of the EnerVista UR Setup main screen. Select the Template Mode > Remove Settings Template option. Enter the template password and click OK to continue. GE Multilin F60 Feeder Protection System...
Page 110: Securing And Locking Flexlogic Equations
Click on Save to save and apply changes to the settings template. Select the Template Mode > View In Template Mode option to view the template. Apply a password to the template then click OK to secure the FlexLogic equation. F60 Feeder Protection System GE Multilin...
Page 111 FlexLogic entries in a settings file have been secured, use the following procedure to lock the settings file to a specific serial number. Select the settings file in the offline window. Right-click on the file and select the Edit Settings File Properties item. GE Multilin F60 Feeder Protection System...
Page 112: Settings File Traceability
When a settings file is transferred to a F60 device, the date, time, and serial number of the F60 are sent back to EnerVista UR Setup and added to the settings file on the local PC. This infor- mation can be compared with the F60 actual values at any later date to determine if security has been compromised.
Page 113 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE The transfer date of a setting file written to a F60 is logged in the relay and can be viewed via EnerVista UR Setup or the front panel display. Likewise, the transfer date of a setting file saved to a local PC is logged in EnerVista UR Setup.
Page 114 ONLINE DEVICE TRACEABILITY INFORMATION The F60 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista UR Setup online window as shown in the example below.
Page 115: Faceplate Interface
LED panel 2 LED panel 3 Display Front panel RS232 port Small user-programmable User-programmable Keypad (control) pushbuttons 1 to 7 pushbuttons 1 to 12 827801A . Figure 4–16: UR-SERIES STANDARD HORIZONTAL FACEPLATE PANELS GE Multilin F60 Feeder Protection System 4-13...
Page 116: Led Indicators
The status indicators in the first column are described below. • IN SERVICE: This LED indicates that control power is applied, all monitored inputs, outputs, and internal systems are OK, and that the device has been programmed. 4-14 F60 Feeder Protection System GE Multilin...
Page 117 Support for applying a customized label beside every LED is provided. Default labels are shipped in the label pack- age of every F60, together with custom templates. The default labels can be replaced by user-printed labels. User customization of LED operation is of maximum benefit in installations where languages other than English are used to communicate with operators.
Page 118 LEDs on these panels. USER-PROGRAMMABLE LEDS USER-PROGRAMMABLE LEDS 842782A1.CDR Figure 4–20: LED PANELS 2 AND 3 (INDEX TEMPLATE) DEFAULT LABELS FOR LED PANEL 2: The default labels are intended to represent: 4-16 F60 Feeder Protection System GE Multilin...
Page 119: Custom Labeling Of Leds
EnerVista UR Setup software is installed and operational • The F60 settings have been saved to a settings file • The F60 front panel label cutout sheet (GE Multilin part number 1006-0047) has been downloaded from http://www.gedigitalenergy.com/products/support/ur/URLEDenhanced.doc and printed •...
Page 120 Enter the text to appear next to each LED and above each user-programmable pushbuttons in the fields provided. Feed the F60 front panel label cutout sheet into a printer and press the Print button in the front panel report window.
Page 121 4.2 FACEPLATE INTERFACE Bend the tab at the center of the tool tail as shown below. The following procedure describes how to remove the LED labels from the F60 enhanced front panel and insert the custom labels. Use the knife to lift the LED label and slide the label tool underneath. Make sure the bent tabs are pointing away from the relay.
Page 122 Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown below. The following procedure describes how to remove the user-programmable pushbutton labels from the F60 enhanced front panel and insert the custom labels.
Page 123 Slide the label tool under the user-programmable pushbutton label until the tabs snap out as shown below. This attaches the label tool to the user-programmable pushbutton label. Remove the tool and attached user-programmable pushbutton label as shown below. GE Multilin F60 Feeder Protection System 4-21...
Page 124 The panel templates provide relative LED locations and located example text (x) edit boxes. The following procedure demonstrates how to install/uninstall the custom panel labeling. Remove the clear Lexan Front Cover (GE Multilin part number: 1501-0014). Push in...
Page 125: Display
INTRODUCTION The F60 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, that can be presented on faceplate LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated from faceplate keypad or automatically initiated from a FlexLogic operand.
Page 126: Keypad
Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a header display page menu item. Each press of the MENU key advances through the following main heading pages: • Actual values • Settings • Commands • Targets • User displays (when enabled) 4-24 F60 Feeder Protection System GE Multilin...
Page 127 FLASH MESSAGE Properties. TIME: 1.0 s  To view the remaining settings associated with the Display Properties subheader, DEFAULT MESSAGE repeatedly press the MESSAGE DOWN key. The last message appears as shown. INTENSITY: 25% GE Multilin F60 Feeder Protection System 4-25...
Page 128: Changing Settings
ENTERING ALPHANUMERIC TEXT Text settings have data values which are fixed in length, but user-defined in character. They can be upper case letters, lower case letters, numerals, and a selection of special characters. 4-26 F60 Feeder Protection System GE Multilin...
Page 129: Settings
The information in this section refers to password security. For information on how to set or change CyberSentry pass- words, see the Settings > Product Setup > Security > CyberSentry section in the next chapter. GE Multilin F60 Feeder Protection System 4-27...
Page 130 When an incorrect command or setting password has been entered via the faceplate interface three times within a 3-minute time span, the FlexLogic operand is set to “On” and the F60 does not allow settings or command LOCAL ACCESS DENIED...
Page 131 FlexLogic operand is set to “On” and the REMOTE ACCESS DENIED F60 does not allow Settings or Command access via the any external communications interface for the next ten minutes. FlexLogic operand is set to “Off” after the expiration of the ten-minute timeout.
Page 132 4.2 FACEPLATE INTERFACE 4 HUMAN INTERFACES 4-30 F60 Feeder Protection System GE Multilin...
Page 133: Overview
See page 5-83.   TELEPROTECTION See page 5-91.   INSTALLATION See page 5-91.   SETTINGS  AC INPUTS See page 5-94.  SYSTEM SETUP   POWER SYSTEM See page 5-95.  GE Multilin F60 Feeder Protection System...
Page 134   UNDERFREQUENCY See page 5-220.   OVERFREQUENCY See page 5-221.   FREQUENCY RATE See page 5-222.  OF CHANGE  SYNCHROCHECK See page 5-224.   AUTORECLOSE See page 5-228.  F60 Feeder Protection System GE Multilin...
Page 135 See page 5-279.  GOOSE ANALOGS  IEC 61850 See page 5-280.  GOOSE UINTEGERS  SETTINGS  DCMA INPUTS See page 5-281.  TRANSDUCER I/O   RTD INPUTS See page 5-282.  GE Multilin F60 Feeder Protection System...
Page 136: Introduction To Elements
(1 pu) would be: 13800 --------------- -  115 V (EQ 5.1) 14400 For wye-connected VTs, the secondary nominal voltage (1 pu) would be: 13800  --------------- - --------- - 66.4 V (EQ 5.2) 14400 F60 Feeder Protection System GE Multilin...
Page 137: Introduction To Ac Sources
BACKGROUND The F60 may be used on systems with breaker-and-a-half or ring bus configurations. In these applications, each of the two three-phase sets of individual phase currents (one associated with each breaker) can be used as an input to a breaker fail- ure element.
Page 138 “bank,” and all four are either current or voltage, as are channels 5, 6, 7 and 8. Channels 1, 2, 3 and 5, 6, 7 are arranged as phase A, B and C respectively. Channels 4 and 8 are either another current or voltage. F60 Feeder Protection System GE Multilin...
Page 139 CTs on each of two breakers is required to measure the winding current flow. GE Multilin F60 Feeder Protection System...
Page 140: Product Setup
If all passwords are lost, recovery is possible by resetting the unit to default values. To reset the unit after a lost password: Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email account. Customer service provides a code to reset the relay to the factory defaults.
Page 141 When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 142 INVALID ATTEMPTS BEFORE LOCKOUT The F60 provides a means to raise an alarm upon failed password entry. Should password verification fail while accessing a password-protected level of the relay (either settings or commands), the FlexLogic operand is UNAUTHORIZED ACCESS asserted.
Page 143 ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout is restarted. The status of this timer is updated every 5 seconds. GE Multilin F60 Feeder Protection System 5-11...
Page 144 It is disabled by default to allow the administrator direct access to the EnerVista software immediately after installation. When security is disabled, all users have administrator access. GE recommends enabling the EnerVista security before placing the device in service.
Page 145 Enter a username in the User field. The username must be 4 to 20 characters in length. Select the user access rights by enabling the check box of one or more of the fields. GE Multilin F60 Feeder Protection System 5-13...
Page 146 Deletes the user account when exiting the user management window Actual Values Allows the user to read actual values Settings Allows the user to read setting values Commands Allows the user to execute commands 5-14 F60 Feeder Protection System GE Multilin...
Page 147 When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication database to authenticate the user. No password or security information is displayed in plain text by the EnerVista software or UR device, nor are they ever transmitted without cryptographic protection. GE Multilin F60 Feeder Protection System 5-15...
Page 148 5.2 PRODUCT SETUP 5 SETTINGS CYBERSENTRY SETTINGS THROUGH ENERVISTA CyberSentry security settings are configured under Device > Settings > Product Setup > Security. Figure 5–2: CYBERSENTRY SECURITY PANEL 5-16 F60 Feeder Protection System GE Multilin...
Page 149 Authentication method used by RADIUS EAP-TTLS EAP-TTLS EAP-TTLS Administrator Authentication server. Currently fixed to EAP-TTLS. Method Timeout Timeout in seconds between re- 9999 Administrator transmission requests Retries Number of retries before giving up 9999 Administrator GE Multilin F60 Feeder Protection System 5-17...
Page 150 See the Change Text The specified role password-protected. All RADIUS users are following following Me1# and Administrator, password-protected. password password except for section for section for Supervisor, where requirements requireme it is only itself 5-18 F60 Feeder Protection System GE Multilin...
Page 151 This role can also be disabled, but only through a Supervisor authentication. When this role is disabled its permissions are assigned to the Administrator role. GE Multilin F60 Feeder Protection System 5-19...
Page 152 LOAD FACTORY DEFAULTS: This setting is used to reset all the settings, communication and security passwords. An Administrator role is used to change this setting and a Supervisor role (if not disabled) approves it. 5-20 F60 Feeder Protection System GE Multilin...
Page 153 Factory Service Mode: When enabled (i.e., "Yes" is selected) the device can go into factory service mode. For this set- ting to become enabled a Supervisor authentication is necessary. The default value is Disabled. GE Multilin F60 Feeder Protection System 5-21...
Page 154 The use of CyberSentry for devices communicating through an Ethernet-to-RS485 gateway is not supported. Because these gateways do not support the secure protocols necessary to communicate with such devices, the connection cannot be established. Use the device as a non-CyberSentry device. 5-22 F60 Feeder Protection System GE Multilin...
Page 155: Display Properties
LEVEL: 0.020 pu Range: 0.1 to 1.0 V secondary in steps of 0.1 VOLTAGE CUT-OFF MESSAGE LEVEL: 1.0 V Some relay messaging characteristics can be modified to suit different situations using the display properties settings. GE Multilin F60 Feeder Protection System 5-23...
Page 156 Some customers prefer very low currents to display as zero, while others prefer the current be displayed even when the value reflects noise rather than the actual signal. The F60 applies a cut- off value to the magnitudes and angles of the measured currents.
Page 157: Clear Relay Records
Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user-programma- ble pushbuttons to clear specific records are typical applications for these commands. Since the F60 responds to rising edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Page 158: Communications
0 ms The F60 is equipped with up to two independent serial communication ports. The faceplate RS232 port is intended for local use and is fixed at 19200 baud and no parity. The rear COM2 port is RS485. The RS485 port has settings for baud rate and parity.
Page 159 The topology shown in the following figure allows communications to SCADA, local configuration/monitoring through EnerVista, and access to the public network shared on the same LAN. No redundancy is provided. Figure 5–4: NETWORK CONFIGURATION FOR SINGLE LAN GE Multilin F60 Feeder Protection System 5-27...
Page 160 LAN2, to which port 2 (P2) is connected and communications with SCADA on LAN3, to which port 3 (P3) is connected. There is no redundancy. Figure 5–6: MULTIPLE LANS, NO REDUNDANCY 5-28 F60 Feeder Protection System GE Multilin...
Page 161 Failover, the operation of ports 2 and 3 is as follows: • Ports 2 and 3 use the port 2 MAC address, IP address, and mask • The configuration fields for IP address and mask on port 3 are hidden GE Multilin F60 Feeder Protection System 5-29...
Page 162 There is a second type of specialized device used in PRP networks, called RedBox, with the role of connecting Single Attached Nodes (SANs) to a redundant network. UR relays implement only the DANP functionality. The RedBox functionality is not implemented. 5-30 F60 Feeder Protection System GE Multilin...
Page 163 1 to 6, that entry becomes a static route and it must meet all the rules listed in the next section, General Conditions to be Satisfied by Static Routes. GE Multilin F60 Feeder Protection System 5-31...
Page 164 Port 1 (IP address 10.1.1.2) connects the UR to LAN 10.1.1.0/24 and to the Internet through Router1. Router 1 has an interface on 10.1.1.0/24 and the IP address of this interface is 10.1.1.1. 5-32 F60 Feeder Protection System GE Multilin...
Page 165 Age, in minutes, of the cache entry. A hyphen (-) means the address is local. Hardware Address LAN hardware address, a MAC address that corresponds to network address Type Dynamic or Static Interface Interface to which this address mapping has been assigned GE Multilin F60 Feeder Protection System 5-33...
Page 166 MODBUS SLAVE ADDRESS RS485 port, each F60 must have a unique address from 1 to 254. Address 0 is the broadcast address which all Modbus slave devices listen to. Addresses do not have to be sequential, but no two devices can have the same address or conflicts resulting in errors will occur.
Page 167 TIMEOUT: 120 s The F60 supports the Distributed Network Protocol (DNP) version 3.0. The F60 can be used as a DNP slave device con- nected to multiple DNP masters (usually an RTU or a SCADA master station). Since the F60 maintains two sets of DNP data change buffers and connection information, two DNP masters can actively communicate with the F60 at one time.
Page 168 DNP analog input points that are voltages will be returned with values 1000 times smaller (for example, a value of 72000 V on the F60 will be returned as 72). These settings are useful when analog input values must be adjusted to fit within cer- tain ranges in DNP masters.
Page 169 When the DNP data points (analog inputs and/or binary inputs) are configured for Ethernet-enabled relays, check the “DNP Points Lists” F60 web page to view the points lists. This page can be viewed with a web browser by enter- ing the F60 IP address to access the F60 “Main Menu”, then by selecting the “Device Information Menu” > “DNP NOTE Points Lists”...
Page 170 60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored. NOTE Changes to the DNP / IEC 60870-5-104 point lists will not take effect until the F60 is restarted. NOTE j) IEC 61850 PROTOCOL ...
Page 171 The F60 supports the Manufacturing Message Specification (MMS) protocol as specified by IEC 61850. MMS is supported over two protocol stacks: TCP/IP over Ethernet. The F60 operates as an IEC 61850 server. The Remote inputs and outputs section in this chapter describe the peer-to-peer GSSE/GOOSE message scheme.
Page 172 DESTINATION MAC address; the least significant bit of the first byte must be set. In F60 releases previous to 5.0x, the destination Ethernet MAC address was determined automatically by taking the sending MAC address (that is, the unique, local MAC address of the F60) and setting the multicast bit.
Page 173 The F60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station components.
Page 174 Configure the transmission dataset. Configure the GOOSE service settings. Configure the data. The general steps required for reception configuration are: Configure the reception dataset. Configure the GOOSE service settings. Configure the data. 5-42 F60 Feeder Protection System GE Multilin...
Page 175 MMXU1 HZ DEADBAND change greater than 45 mHz, from the previous MMXU1.MX.mag.f value, in the source frequency. The F60 must be rebooted (control power removed and re-applied) before these settings take effect. The following procedure illustrates the reception configuration. Configure the reception dataset by making the following changes in the ...
Page 176 IEC61850 GOOSE ANALOG INPUT 1 UNITS The GOOSE analog input 1 can now be used as a FlexAnalog value in a FlexElement or in other settings. The F60 must be rebooted (control power removed and re-applied) before these settings take effect.
Page 177 DNA and UserSt bit pairs that are included in GSSE messages. To set up a F60 to receive a configurable GOOSE dataset that contains two IEC 61850 single point status indications, the following dataset items can be selected (for example, for configurable GOOSE dataset 1): “GGIO3.ST.Ind1.stVal” and “GGIO3.ST.Ind2.stVal”.
Page 178 CPU resources. When server scanning is disabled, there is no updating of the IEC 61850 logical node status values in the F60. Clients are still able to connect to the server (F60 relay), but most data values are not updated. This set- ting does not affect GOOSE/GSSE operation.
Page 179 (_) character, and the first character in the prefix must be a letter. This conforms to the IEC 61850 standard. Changes to the logical node prefixes will not take effect until the F60 is restarted. The main menu for the IEC 61850 MMXU deadbands is shown below.
Page 180 The GGIO2 control configuration settings are used to set the control model for each input. The available choices are “0” (status only), “1” (direct control), and “2” (SBO with normal security). The GGIO2 control points are used to control the F60 virtual inputs.
Page 181 GGIO1 (binary status values). The settings allow the selection of FlexInteger values for each GGIO5 integer value point. It is intended that clients use GGIO5 to access generic integer values from the F60. Additional settings are provided to allow the selection of the number of integer values available in GGIO5 (1 to 16), and to assign FlexInteger values to the GGIO5 integer inputs.
Page 182 ITEM 64 attributes supported by the F60. Changes to the dataset will only take effect when the F60 is restarted. It is recommended to use reporting service from logical node LLN0 if a user needs some (but not all) data from already existing GGIO1, GGIO4, and MMXU4 points and their quantity is not greater than 64 minus the number items in this dataset.
Page 183 XCBR operating counter status attribute (OpCnt) increments with every operation. Frequent breaker operation can result in very large OpCnt values over time. This setting allows the OpCnt to be reset to “0” for XCBR1. GE Multilin F60 Feeder Protection System 5-51...
Page 184 Since GSSE/GOOSE messages are multicast Ethernet by specification, they are not usually be forwarded by net- work routers. However, GOOSE messages may be forwarded by routers if the router has been configured for VLAN functionality. NOTE 5-52 F60 Feeder Protection System GE Multilin...
Page 185 Menu”. Web pages are available showing DNP and IEC 60870-5-104 points lists, Modbus registers, event records, fault reports, and so on. First connect the UR and a computer to an Ethernet network, then enter the IP address of the F60 into the “Address”...
Page 186 ENABLED: No The F60 supports the IEC 60870-5-104 protocol. The F60 can be used as an IEC 60870-5-104 slave device connected to a maximum of two masters (usually either an RTU or a SCADA master station). Since the F60 maintains two sets of IEC 60870-5-104 data change buffers, no more than two masters should actively communicate with the F60 at one time.
Page 187 MESSAGE  CONFIGURATION The F60 Feeder Protection System is provided with optional Ethernet Global Data (EGD) communications capability. This feature is specified as a software option at the time of ordering. See the Ordering section of chapter 2 for additional details.
Page 188 MESSAGE (Modbus register address range) Fast exchanges (50 to 1000 ms) are generally used in control schemes. The F60 has one fast exchange (exchange 1) and two slow exchanges (exchange 2 and 3). The settings menu for the slow EGD exchanges is shown below: ...
Page 189: Modbus User Map
EXCH 1 DATA ITEM 1 to 20/50: These settings specify the data items that are part of this EGD exchange. Almost any data from the F60 memory map can be configured to be included in an EGD exchange. The settings are the starting Modbus register address for the data item in decimal format.
Page 190 The relay implements PTP according to IEEE Std 1588 2008 and the equivalent IEC 61588:2009(E), sometimes referred to as version 2 PTP. It does not support the previous version of the standard (version 1). NOTE 5-58 F60 Feeder Protection System GE Multilin...
Page 191 • Depending on the characteristics of the device to which the relay is directly linked, VLAN ID may have no effect. • This setting applies to all of the relay’s PTP capable ports. GE Multilin F60 Feeder Protection System 5-59...
Page 192 F60 clock is closely synchronized with the SNTP/ NTP server. It takes up to two minutes for the F60 to signal an SNTP self-test error if the server is offline.
Page 193 DST rules of the local time zone. DAYLIGHT SAVINGS TIME (DST) Note that when IRIG-B time synchronization is active, the local time in the IRIG-B signal contains any daylight savings time offset and so the DST settings are ignored. GE Multilin F60 Feeder Protection System 5-61...
Page 194: Fault Reports
MESSAGE Z0 ANGLE: 75° The F60 relay supports one fault report and an associated fault locator. The signal source and trigger condition, as well as the characteristics of the line or feeder, are entered in this menu. The fault report stores data, in non-volatile memory, pertinent to an event when triggered. The captured data contained in the FaultReport.txt file includes:...
Page 195 It should be kept in mind that grounding points in vicinity of the installation impact the system zero-sequence impedance (grounded loads, reactors, zig-zag transformers, shunt capacitor banks, etc.). GE Multilin F60 Feeder Protection System 5-63...
Page 196: Oscillography
64 samples per cycle; that is, it has no effect on the fundamental calculations of the device. When changes are made to the oscillography settings, all existing oscillography records will be CLEARED. NOTE 5-64 F60 Feeder Protection System GE Multilin...
Page 197 IB signal on terminal 2 of the CT/VT module in slot F. If there are no CT/VT modules and analog input modules, no analog traces will appear in the file; only the digital traces will appear. GE Multilin F60 Feeder Protection System 5-65...
Page 198: Data Logger
The relay automatically partitions the available memory between the channels in use. Exam- ple storage capacities for a system frequency of 60 Hz are shown in the following table. 5-66 F60 Feeder Protection System GE Multilin...
Page 199 – entering this number via the relay keypad will cause the corresponding parameter to be displayed. • DATA LOGGER CONFIG: This display presents the total amount of time the Data Logger can record the channels not selected to “Off” without over-writing old data. GE Multilin F60 Feeder Protection System 5-67...
Page 200: Demand
Start Demand Interval logic input pulses. Each new value of demand becomes available at the end of each pulse. Assign a FlexLogic operand to the setting to program the input for the new DEMAND TRIGGER demand interval pulses. 5-68 F60 Feeder Protection System GE Multilin...
Page 201: User-Programmable Leds
LEDs. This test checks for hardware failures that lead to more than one LED being turned off from a single logic point. This stage can be interrupted at any time. GE Multilin F60 Feeder Protection System 5-69...
Page 202 LEDs are being visually inspected. When finished, the pushbutton should be released. The relay will then automatically start stage 2. At this point forward, test may be aborted by pressing the pushbutton. 5-70 F60 Feeder Protection System GE Multilin...
Page 203: User-Programmable Self-Tests
Range: Disabled, Enabled. SFP MODULE FAIL MESSAGE FUNCTION: Disabled All major self-test alarms are reported automatically with their corresponding FlexLogic operands, events, and targets. Most of the minor alarms can be disabled if desired. GE Multilin F60 Feeder Protection System 5-71...
Page 204 ANY SELF-TEST mode, minor alarms continue to function along with other major and minor alarms. Refer to the Relay self-tests section in chapter 7 for additional information on major and minor self-test alarms. 5-72 F60 Feeder Protection System GE Multilin...
Page 205: Control Pushbuttons
The location of the control pushbuttons are shown in the following figures. Control pushbuttons 842813A1.CDR Figure 5–11: CONTROL PUSHBUTTONS (ENHANCED FACEPLATE) An additional four control pushbuttons are included on the standard faceplate when the F60 is ordered with the twelve user- programmable pushbutton option. STATUS EVENT CAUSE...
Page 206 SYSTEM SETUP/ BREAKERS/BREAKER 1/ BREAKER 1 PUSHBUTTON CONTROL Enabled=1 TIMER FLEXLOGIC OPERAND SYSTEM SETUP/ BREAKERS/BREAKER 2/ CONTROL PUSHBTN 1 ON 100 msec BREAKER 2 PUSHBUTTON CONTROL 842010A2.CDR Enabled=1 Figure 5–13: CONTROL PUSHBUTTON LOGIC 5-74 F60 Feeder Protection System GE Multilin...
Page 207: User-Programmable Pushbuttons
FlexLogic equations, protection elements, and control elements. Typical applications include breaker control, autorecloser blocking, and setting groups changes. The user-programmable pushbuttons are under the control level of password protection. The user-configurable pushbuttons for the enhanced faceplate are shown below. GE Multilin F60 Feeder Protection System 5-75...
Page 208 The pulse duration of the remote set, remote reset, or local pushbutton must be at least 50 ms to operate the push- button. This allows the user-programmable pushbuttons to properly operate during power cycling events and vari- ous system disturbances that may cause transient assertion of the operating signals. NOTE 5-76 F60 Feeder Protection System GE Multilin...
Page 209 PUSHBTN 1 SET PUSHBTN 1 RESET • PUSHBTN 1 LOCAL: This setting assigns the FlexLogic operand serving to inhibit pushbutton operation from the front panel pushbuttons. This locking functionality is not applicable to pushbutton autoreset. GE Multilin F60 Feeder Protection System 5-77...
Page 210 “Normal” if the setting is “High Priority” or “Normal”. PUSHBTN 1 MESSAGE • PUSHBUTTON 1 EVENTS: If this setting is enabled, each pushbutton state change will be logged as an event into event recorder. 5-78 F60 Feeder Protection System GE Multilin...
Page 211 Off = 0 SETTING SETTING Autoreset Delay Autoreset Function = Enabled = Disabled SETTING Drop-Out Timer TIMER FLEXLOGIC OPERAND 200 ms PUSHBUTTON 1 ON 842021A3.CDR Figure 5–16: USER-PROGRAMMABLE PUSHBUTTON LOGIC (Sheet 1 of 2) GE Multilin F60 Feeder Protection System 5-79...
Page 212: Flex State Parameters
PATH: SETTINGS PRODUCT SETUP FLEX STATE PARAMETERS Range: FlexLogic operand  FLEX STATE PARAMETER  PARAMETERS Range: FlexLogic operand PARAMETER MESSAGE Range: FlexLogic operand PARAMETER MESSAGE  Range: FlexLogic operand PARAMETER 256: MESSAGE 5-80 F60 Feeder Protection System GE Multilin...
Page 213: User-Definable Displays
INVOKE AND SCROLL play, not at the first user-defined display. The pulses must last for at least 250 ms to take effect. INVOKE AND SCROLL GE Multilin F60 Feeder Protection System 5-81...
Page 214 While viewing a user display, press the ENTER key and then select the ‘Yes” option to remove the display from the user display list. Use the MENU key again to exit the user displays menu. 5-82 F60 Feeder Protection System GE Multilin...
Page 215: Direct Inputs/Outputs
See page 5–89. MESSAGE   CRC ALARM CH2 See page 5–89. MESSAGE   UNRETURNED See page 5–90. MESSAGE  MESSAGES ALARM CH1  UNRETURNED See page 5–90. MESSAGE  MESSAGES ALARM CH2 GE Multilin F60 Feeder Protection System 5-83...
Page 216 Delivery time for direct input and output messages is approximately 0.2 of a power system cycle at 128 kbps and 0.4 of a power system cycle at 64 kbps, per each ‘bridge’. 5-84 F60 Feeder Protection System GE Multilin...
Page 217 The following application examples illustrate the basic concepts for direct input and output configuration. Please refer to the Inputs and outputs section in this chapter for information on configuring FlexLogic operands (flags, bits) to be exchanged. GE Multilin F60 Feeder Protection System 5-85...
Page 218 UR IED 1 BLOCK UR IED 4 UR IED 2 UR IED 3 842712A1.CDR Figure 5–19: SAMPLE INTERLOCKING BUSBAR PROTECTION SCHEME For increased reliability, a dual-ring configuration (shown below) is recommended for this application. 5-86 F60 Feeder Protection System GE Multilin...
Page 219 The complete application requires addressing a number of issues such as failure of both the communications rings, failure or out-of-service conditions of one of the relays, etc. Self-monitoring flags of the direct inputs and outputs feature would be primarily used to address these concerns. GE Multilin F60 Feeder Protection System 5-87...
Page 220 Inputs and outputs section. A blocking pilot-aided scheme should be implemented with more security and, ideally, faster message delivery time. This could be accomplished using a dual-ring configuration as shown below. 5-88 F60 Feeder Protection System GE Multilin...
Page 221 EVENTS: Disabled The F60 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The monitoring function counts all incoming messages, including messages that failed the CRC check.
Page 222 MESSAGE EVENTS: Disabled The F60 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unre- turned messages.
Page 223: Teleprotection
TERMINAL 1 ID NUMBER 5.2.19 INSTALLATION   PATH: SETTINGS PRODUCT SETUP INSTALLATION Range: Not Programmed, Programmed  INSTALLATION RELAY SETTINGS:  Not Programmed Range: up to 20 alphanumeric characters RELAY NAME: MESSAGE Relay-1 GE Multilin F60 Feeder Protection System 5-91...
Page 224 "Programmed" state. UNIT NOT PROGRAMMED setting allows the user to uniquely identify a relay. This name will appear on generated reports. RELAY NAME 5-92 F60 Feeder Protection System GE Multilin...
Page 225: Remote Resources Configuration
Bricks. Remote resources settings configure the point-to-point connection between specific fiber optic ports on the F60 process card and specific Brick. The relay is then configured to measure spe- cific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
Page 226: Ac Inputs
CTs will be adjusted to that created by a 1000:1 CT before summation. If a protection element is set up to act on SRC 1 cur- rents, then a pickup level of 1 pu will operate on 1000 A primary. The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5-94 F60 Feeder Protection System GE Multilin...
Page 227: Power System
 POWER SYSTEM NOMINAL FREQUENCY:  60 Hz Range: ABC, ACB PHASE ROTATION: MESSAGE Range: SRC 1, SRC 2 FREQUENCY AND PHASE MESSAGE REFERENCE: SRC 1 Range: Disabled, Enabled FREQUENCY TRACKING: MESSAGE Enabled GE Multilin F60 Feeder Protection System 5-95...
Page 228: Signal Sources
FREQUENCY TRACKING frequency applications. NOTE The frequency tracking feature functions only when the F60 is in the “Programmed” mode. If the F60 is “Not Pro- grammed”, then metering values are available but can exhibit significant errors. NOTE 5.4.3 SIGNAL SOURCES ...
Page 229 CTs will be summed together. When the F60 is equipped with a type 8Z CT/VT module for high impedance fault detection, the CT bank of this module should not be assigned to a source which will be used by any conventional protection element. The type 8Z module CT bank is used solely by the high impedance fault detection algorithm.
Page 230 UR Relay Figure 5–26: EXAMPLE USE OF SOURCES Y LV D HV SRC 1 SRC 2 SRC 3 Phase CT F1+F5 None Ground CT None None Phase VT None None Aux VT None None 5-98 F60 Feeder Protection System GE Multilin...
Page 231: Breakers
Range: 0.000 to 65.535 s in steps of 0.001 MANUAL CLOSE RECAL1 MESSAGE TIME: 0.000 s Range: FlexLogic operand BREAKER 1 OUT OF SV: MESSAGE Range: Disabled, Enabled BREAKER 1 EVENTS: MESSAGE Disabled GE Multilin F60 Feeder Protection System 5-99...
Page 232 1. The number of breaker control elements is dependent on the number of CT/VT modules specified with the F60. The follow- ing settings are available for each breaker control element.
Page 233 5 SETTINGS 5.4 SYSTEM SETUP Figure 5–27: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 1 of 2) IEC 61850 functionality is permitted when the F60 is in “Programmed” mode and not in the local control mode. NOTE GE Multilin F60 Feeder Protection System...
Page 234 Note that IEC 61850 commands are event-driven and dwell time for these is one protection pass only. If you want to main- tain the close/open command for a certain time, do so either on the contact outputs using the "Seal-in" setting or in Flex- Logic. 5-102 F60 Feeder Protection System GE Multilin...
Page 235: Disconnect Switches
For greater security in determination of the switch pole position, both the 89/a and 89/b auxiliary contacts are used with reporting of the discrepancy between them. The number of available disconnect switches depends on the number of the CT/VT modules ordered with the F60. •...
Page 236 SWITCH 1 ALARM DELAY: This setting specifies the delay interval during which a disagreement of status among the three-pole position tracking operands will not declare a pole disagreement. This allows for non-simultaneous operation of the poles. IEC 61850 functionality is permitted when the F60 is in “Programmed” mode and not in the local control mode. NOTE 5-104...
Page 237 5 SETTINGS 5.4 SYSTEM SETUP Figure 5–29: DISCONNECT SWITCH SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-105...
Page 238: Flexcurves
0.86 15.0 0.48 0.88 15.5 0.50 0.90 16.0 0.52 0.91 16.5 0.54 0.92 17.0 0.56 0.93 17.5 0.58 0.94 18.0 0.60 0.95 18.5 0.62 0.96 19.0 0.64 0.97 19.5 0.66 0.98 10.0 20.0 5-106 F60 Feeder Protection System GE Multilin...
Page 239 The multiplier and adder settings only affect the curve portion of the characteristic and not the MRT and HCT set- tings. The HCT settings override the MRT settings for multiples of pickup greater than the HCT ratio. NOTE GE Multilin F60 Feeder Protection System 5-107...
Page 240 EnerVista UR Setup software generates an error message and discards the proposed changes. NOTE e) STANDARD RECLOSER CURVES The standard recloser curves available for the F60 are displayed in the following graphs. 5-108 F60 Feeder Protection System...
Page 241 CURRENT (multiple of pickup) 842723A1.CDR Figure 5–33: RECLOSER CURVES GE101 TO GE106 GE142 GE138 GE120 GE113 0.05 7 8 9 10 12 CURRENT (multiple of pickup) 842725A1.CDR Figure 5–34: RECLOSER CURVES GE113, GE120, GE138 AND GE142 GE Multilin F60 Feeder Protection System 5-109...
Page 242 Figure 5–35: RECLOSER CURVES GE134, GE137, GE140, GE151 AND GE201 GE152 GE141 GE131 GE200 7 8 9 10 12 CURRENT (multiple of pickup) 842728A1.CDR Figure 5–36: RECLOSER CURVES GE131, GE141, GE152, AND GE200 5-110 F60 Feeder Protection System GE Multilin...
Page 243 Figure 5–37: RECLOSER CURVES GE133, GE161, GE162, GE163, GE164 AND GE165 GE132 GE139 GE136 GE116 0.05 GE117 GE118 0.02 0.01 7 8 9 10 12 CURRENT (multiple of pickup) 842726A1.CDR Figure 5–38: RECLOSER CURVES GE116, GE117, GE118, GE132, GE136, AND GE139 GE Multilin F60 Feeder Protection System 5-111...
Page 244 Figure 5–39: RECLOSER CURVES GE107, GE111, GE112, GE114, GE115, GE121, AND GE122 GE202 GE135 GE119 7 8 9 10 12 CURRENT (multiple of pickup) 842727A1.CDR Figure 5–40: RECLOSER CURVES GE119, GE135, AND GE202 5-112 F60 Feeder Protection System GE Multilin...
Page 245: Phasor Measurement Unit
Synchrophasors from different locations within the power system are networked to a central location. The F60 offers PMU features over two communication standards, IEC61850-9-5 and IEEE C37.118. The figure shows complete Synchrophasor implementation.
Page 246 PMUS AGGREGATORS INPUTS D60, F60, G60, L30, L90, T60 Precise time input to the relay from the international time standard, via either IRIG-B or PTP, is vital for correct syn- chrophasor measurement and reporting. For IRIG-B, a DC level shift IRIG-B receiver must be used for the phasor measurement unit to output proper synchrophasor values.
Page 247 16 character name field provided within the Basic Configuration menu. Additionally, the names of the 16 binary points are implemented as numbered descriptions — d1, d2, d3, and so on. The number of descriptions are equal to the number of bits configured in the 16 bit digital status word. GE Multilin F60 Feeder Protection System 5-115...
Page 248 From each PMU the user selects the phasor information of interest that is mapped into the selected aggregator datset(s). For version 7.0 only FCDA data is supported. Figure 5–44: DATA SET CREATED FROM USER SELECTED INTERNAL ITEMS 5-116 F60 Feeder Protection System GE Multilin...
Page 249 CONFIGURATION EXAMPLE: CFG-2 BASED CONFIGURATION (USING IEC61850-90-5) The F60 is expected to send the CFG-2 file (IEEE C37.118 config. file) upon request from the upstream synchrophasor devices (e.g., P30) without stopping R-SV multicasting, see figure below. The primary domain controller (PDC) does not need to use a stop/start data stream command if the UR protocol is set to IEC61850-90-5 prior to requesting the configura- tion via CFG-2 (IEEE C37.118 config.
Page 250 See page 5-119.  UNIT 1  CONFIGURATION  PMU 1 See page 5-123. MESSAGE  CALIBRATION  PMU 1 See page 5-124. MESSAGE  TRIGGERING  PMU 1 See page 5-131. MESSAGE  RECORDING 5-118 F60 Feeder Protection System GE Multilin...
Page 251 Range: 1 to 65534 in steps of 1 PMU 1 IDCODE: MESSAGE Range: 32-character ASCII string truncated to 16 PMU 1 STN: MESSAGE characters if mapped into C37.118 Default: GE-UR-PMU GE-UR-PMU Range: Available signal sources PMU 1 SIGNAL SOURCE: MESSAGE SRC 1...
Page 252 For a system frequency of 60 Hz (50 Hz), the F60 generates a reporting mismatch message if the selected rate is not set as 10 Hz, 12 Hz, 15 Hz, 20 Hz, 30 Hz, 60 Hz, or 120 Hz (or 10 Hz, 25 Hz, 50 Hz or 100 Hz when the system frequency is 50 Hz) when entered via the keypad or software;...
Page 253 This setting complies with bit-1 of the FORMAT field of the IEEE C37.118 configuration frame. This setting applies to synchrophasors only; the user-selectable FlexAnalog channels are always transmitted as 16-bit integer values. GE Multilin F60 Feeder Protection System 5-121...
Page 254 As per IEC 61850-6 standard specification, the PMU LD Name is the concatenated combination (to total 64 charac- ters) of IED Name (specified in IEC 61850 Server Settings) appended with PMU X LDINST string. NOTE 5-122 F60 Feeder Protection System GE Multilin...
Page 255 VTs, CTs, and cabling. The setting values are effectively added to the measured angles. Therefore, enter a positive correction of the secondary signal lags the true signal; and negative value if the secondary signal leads the true signal. GE Multilin F60 Feeder Protection System 5-123...
Page 256 When receiving synchrophasor data at multiple locations, with possibly different reference nodes, it can be more beneficial to allow the central locations to perform the compensation of sequence voltages. This setting applies to PMU data only. The F60 calculates symmetrical voltages independently for protection and control purposes without applying this correction.
Page 257 DPO TIME: 1.00 s Range: FlexLogic operand PMU 1 FREQ TRIG BLK: MESSAGE Range: Self-Reset, Latched, Disabled PMU 1 FREQ TRIGGER MESSAGE TARGET: Self-Reset Range: Enabled, Disabled PMU 1 FREQ TRIGGER MESSAGE EVENTS: Disabled GE Multilin F60 Feeder Protection System 5-125...
Page 258 F60 standards. This element requires the frequency is above the minimum measurable value. If the frequency is below this value, such as when the circuit is de-energized, the trigger drops out.
Page 259 This element responds to elevated current. The trigger responds to the phase current signal of the phasor measurement unit (PMU) source. All current channel (A, B, and C) are processed independently and could trigger the recorder. GE Multilin F60 Feeder Protection System 5-127...
Page 260 VT ratio and the nominal primary current. For the three-phase power, 1 pu is three times that for a single-phase power in case of wye-connected VTs and times in case of delta-connected VTs. The comparator applies a 3% hys- teresis. 5-128 F60 Feeder Protection System GE Multilin...
Page 261 PMU 1 POWER TRIGGER DPO TIME: This setting could be used to extend the trigger after the situation returned to normal. This setting is of particular importance when using the recorder in the forced mode (recording as long as the triggering condition is asserted). Figure 5–51: POWER TRIGGER SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-129...
Page 262 PMU 1 df/dt TRIGGER DPO TIME: PMU 1 SIGNAL FLEXLOGIC OPERAND SOURCE: df/dt > RAISE PMU 1 ROCOF TRIGGER ROCOF, df/dt –df/dt > FALL 847000A1.CDR Figure 5–52: RATE OF CHANGE OF FREQUENCY TRIGGER SCHEME LOGIC 5-130 F60 Feeder Protection System GE Multilin...
Page 263 PMU AGGREGATOR 1 Default: 4712  CONFIGURATION TCP PORT: 4712 Range: 1 to 65534 PMU AGGREGATOR 1 MESSAGE Default: 4713 UDP PORT: 4713 Range: Disabled, Enabled PMU AGGREGATOR 1 MESSAGE Default: Disabled PDC CONTROL: Disabled GE Multilin F60 Feeder Protection System 5-131...
Page 264 AGTR2 PDC CNTRL 3 Phasor data concentrator asserts control bit 3 as received via the network.  as above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, as received via the network. 5-132 F60 Feeder Protection System GE Multilin...
Page 265 R-SV frames. If remote client control is disabled, a negative response is pro- vided to the client in response to a write attempt. A FlexLogic operand (SvEna) is provided for each Aggregator that GE Multilin F60 Feeder Protection System 5-133...
Page 266 MSVCB 1 Security: This setting selects the level of security and authentication used, as outlined in the following table, and is in the form of an enumeration as per standard. The range is 0 to 2. Shaded settings in the table are not supported in firmware 7.0. ENUMERATION AUTHENTICATION ENCRYPTION NOTE 5-134 F60 Feeder Protection System GE Multilin...
Page 267: Introduction To Flexlogic
Figure 5–54: UR ARCHITECTURE OVERVIEW The states of all digital signals used in the F60 are represented by flags (or FlexLogic operands, which are described later in this section). A digital “1” is represented by a 'set' flag. Any external contact change-of-state can be used to block an ele- ment from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output.
Page 268 Some types of operands are present in the relay in multiple instances; e.g. contact and remote inputs. These types of oper- ands are grouped together (for presentation purposes only) on the faceplate display. The characteristics of the different types of operands are listed in the table below. Table 5–13: F60 FLEXLOGIC OPERAND TYPES OPERAND TYPE STATE...
Page 269 5 SETTINGS 5.5 FLEXLOGIC The operands available for this relay are listed alphabetically by types in the following table. Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 1 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION CONTROL CONTROL PUSHBTN 1 ON Control pushbutton 1 is being pressed...
Page 270 5.5 FLEXLOGIC 5 SETTINGS Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 2 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT BRK RESTRIKE 1 OP Breaker restrike detected in any phase of the breaker control 1 element. Breaker restrike BRK RESTRIKE 1 OP A Breaker restrike detected in phase A of the breaker control 1 element.
Page 271 5 SETTINGS 5.5 FLEXLOGIC Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 3 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: FxE 1 PKP FlexElement 1 has picked up FlexElements FxE 1 OP FlexElement 1 has operated FxE 1 DPO FlexElement 1 has dropped out...
Page 272 5.5 FLEXLOGIC 5 SETTINGS Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 4 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: NEG SEQ TOC1 PKP Negative-sequence time overcurrent 1 has picked up Negative-sequence NEG SEQ TOC1 OP Negative-sequence time overcurrent 1 has operated...
Page 273 5 SETTINGS 5.5 FLEXLOGIC Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 5 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: PHASE TOC1 PKP At least one phase of phase time overcurrent 1 has picked up Phase time PHASE TOC1 OP...
Page 274 5.5 FLEXLOGIC 5 SETTINGS Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 6 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: SH STAT GND STG1 PKP Stage 1 of the sub-harmonic stator ground protection has picked up Sub-harmonic stator SH STAT GND STG1 DPO...
Page 275 5 SETTINGS 5.5 FLEXLOGIC Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 7 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: TELEPRO CH1 FAIL Channel 1 failed Teleprotection TELEPRO CH2 FAIL Channel 2 failed channel tests TELEPRO CH1 ID FAIL The ID check for a peer relay on channel 1 has failed...
Page 276 5.5 FLEXLOGIC 5 SETTINGS Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 8 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION INPUTS/OUTPUTS: Virt Ip 1 Flag is set, logic=1 Virtual inputs Virt Ip 2 Flag is set, logic=1 Virt Ip 3 Flag is set, logic=1 ...
Page 277 5 SETTINGS 5.5 FLEXLOGIC Table 5–14: F60 FLEXLOGIC OPERANDS (Sheet 9 of 9) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION SELF- ANY MAJOR ERROR Any of the major self-test errors generated (major error) DIAGNOSTICS ANY MINOR ERROR Any of the minor self-test errors generated (minor error)
Page 278: Flexlogic Rules
When making changes to settings, all FlexLogic equations are re-compiled whenever any new setting value is entered, so all latches are automatically reset. If it is necessary to re-initialize FlexLogic during testing, for example, it is suggested to power the unit down and then back up. 5-146 F60 Feeder Protection System GE Multilin...
Page 279: Flexlogic Example
DIGITAL ELEMENT 1 on Dropout State=Pickup (200 ms) DIGITAL ELEMENT 2 Timer 1 State=Operated Time Delay on Pickup (800 ms) CONTACT INPUT H1c State=Closed VIRTUAL OUTPUT 3 827026A2.VSD Figure 5–56: LOGIC EXAMPLE WITH VIRTUAL OUTPUTS GE Multilin F60 Feeder Protection System 5-147...
Page 280 Following the procedure outlined, start with parameter 99, as follows: 99: The final output of the equation is virtual output 3, which is created by the operator "= Virt Op n". This parameter is therefore "= Virt Op 3." 5-148 F60 Feeder Protection System GE Multilin...
Page 281 87: The input just below the upper input to OR #1 is operand “Virt Op 2 On". 86: The upper input to OR #1 is operand “Virt Op 1 On". 85: The last parameter is used to set the latch, and is operand “Virt Op 4 On". GE Multilin F60 Feeder Protection System 5-149...
Page 282 In the following equation, virtual output 3 is used as an input to both latch 1 and timer 1 as arranged in the order shown below: DIG ELEM 2 OP Cont Ip H1c On AND(2) 5-150 F60 Feeder Protection System GE Multilin...
Page 283: Flexlogic Equation Editor
TIMER 1 TYPE: This setting is used to select the time measuring unit. • TIMER 1 PICKUP DELAY: Sets the time delay to pickup. If a pickup delay is not required, set this function to "0". GE Multilin F60 Feeder Protection System 5-151...
Page 284: Flexelements
The element can be programmed to respond either to a signal level or to a rate-of-change (delta) over a pre-defined period of time. The output operand is asserted when the operating signal is higher than a threshold or lower than a threshold as per user's choice. 5-152 F60 Feeder Protection System GE Multilin...
Page 285 The FLEXELEMENT 1 DIRECTION following figure explains the application of the FLEXELEMENT 1 DIRECTION FLEXELEMENT 1 PICKUP FLEXELEMENT 1 HYS- settings. TERESIS GE Multilin F60 Feeder Protection System 5-153...
Page 286 DIRECTION = Under; FLEXELEMENT INPUT MODE = Signed; FlexElement 1 OpSig FLEXELEMENT 1 PKP FLEXELEMENT DIRECTION = Under; FLEXELEMENT INPUT MODE = Absolute; FlexElement 1 OpSig 842706A2.CDR Figure 5–64: FLEXELEMENT INPUT MODE SETTING 5-154 F60 Feeder Protection System GE Multilin...
Page 287 “Delta”. FLEXELEMENT 1 COMP MODE This setting specifies the pickup delay of the element. The setting FLEXELEMENT 1 PKP DELAY FLEXELEMENT 1 RST DELAY specifies the reset delay of the element. GE Multilin F60 Feeder Protection System 5-155...
Page 288: Non-Volatile Latches
LATCH N LATCH N LATCH N LATCH N TYPE RESET Reset Dominant Previous Previous State State Dominant Previous Previous State State Figure 5–65: NON-VOLATILE LATCH OPERATION TABLE (N = 1 to 16) AND LOGIC 5-156 F60 Feeder Protection System GE Multilin...
Page 289: Overview
Each of the six setting group menus is identical. Setting group 1 (the default active group) automatically becomes active if no other group is active (see the Control elements section for additional details). GE Multilin F60 Feeder Protection System 5-157...
Page 290: Load Encroachment
The element operates if the positive-sequence voltage is above a settable level and asserts its output signal that can be used to block selected protection elements such as distance or phase overcurrent. The following figure shows an effect of the load encroachment characteristics used to block the quadrilateral distance element. 5-158 F60 Feeder Protection System GE Multilin...
Page 291 If the voltage is below this threshold a blocking signal will not be asserted by the element. When selecting this setting one must remember that the F60 measures the phase-to-ground sequence voltages regardless of the VT connection.
Page 292: Phase Current
(2) phase directional overcurrent elements. b) INVERSE TIME OVERCURRENT CHARACTERISTICS The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t stan- dard curve shapes. This allows for simplified coordination with downstream devices.
Page 293 5.041 4.827 38.634 22.819 14.593 11.675 10.130 9.153 8.470 7.960 7.562 7.241 51.512 30.426 19.458 15.567 13.507 12.204 11.294 10.614 10.083 9.654 10.0 64.390 38.032 24.322 19.458 16.883 15.255 14.117 13.267 12.604 12.068 GE Multilin F60 Feeder Protection System 5-161...
Page 294 0.60 1.835 1.067 0.668 0.526 0.451 0.404 0.371 0.346 0.327 0.311 0.80 2.446 1.423 0.890 0.702 0.602 0.538 0.494 0.461 0.435 0.415 1.00 3.058 1.778 1.113 0.877 0.752 0.673 0.618 0.576 0.544 0.518 5-162 F60 Feeder Protection System GE Multilin...
Page 295 = characteristic constant, and T = reset time in seconds (assuming energy capacity is 100% RESET is “Timed”) RESET Table 5–23: GE TYPE IAC INVERSE TIME CURVE CONSTANTS IAC CURVE SHAPE IAC Extreme Inverse 0.0040 0.6379 0.6200 1.7872 0.2461...
Page 296 = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET RECLOSER CURVES: The F60 uses the FlexCurve feature to facilitate programming of 41 recloser curves. Please refer to the FlexCurve section in this chapter for additional details. 5-164...
Page 297 (Mvr) corresponding to the phase-phase voltages of the voltage restraint characteristic curve (see the figure below); the pickup level is calculated as ‘Mvr’ times the setting. If the voltage restraint feature PHASE TOC1 PICKUP is disabled, the pickup level always remains at the setting value. GE Multilin F60 Feeder Protection System 5-165...
Page 298 5.6 GROUPED ELEMENTS 5 SETTINGS Phase-Phase Voltage ÷ VT Nominal Phase-phase Voltage 818784A4.CDR Figure 5–69: PHASE TIME OVERCURRENT VOLTAGE RESTRAINT CHARACTERISTIC Figure 5–70: PHASE TIME OVERCURRENT 1 SCHEME LOGIC 5-166 F60 Feeder Protection System GE Multilin...
Page 299 The input current is the fundamental phasor magnitude. For timing curves, see the publication Instan- taneous Overcurrent Element Response to Saturated Waveforms in UR-Series Relays (GET-8400A). Figure 5–71: PHASE INSTANTANEOUS OVERCURRENT 1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-167...
Page 300 CTs and the line-line voltage from the VTs, based on the 90° or quadrature connection. If there is a requirement to supervise overcurrent elements for flows in opposite directions, such as can happen through a bus-tie breaker, two phase directional elements should be programmed with opposite element characteristic angle (ECA) settings. 5-168 F60 Feeder Protection System GE Multilin...
Page 301 10 ms must be added to all the instantaneous protection elements under the supervi- sion of the phase directional element. If current reversal is of a concern, a longer delay – in the order of 20 ms – may be needed. GE Multilin F60 Feeder Protection System 5-169...
Page 302: Neutral Current
 DIRECTIONAL OC1  NEUTRAL See page 5–173. MESSAGE  DIRECTIONAL OC2 The F60 Feeder Protection System has two (2) Neutral Time Overcurrent, two (2) Neutral Instantaneous Overcurrent, and two (2) Neutral Directional Overcurrent elements. 5-170 F60 Feeder Protection System GE Multilin...
Page 303 For example, if the element reset characteristic is set to “Instan- taneous” and the element is blocked, the time accumulator will be cleared immediately. Figure 5–74: NEUTRAL TIME OVERCURRENT 1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-171...
Page 304 The operating quantity depends on how test currents are injected into the relay (single-phase injection:   0.9375 I ; three-phase pure zero-sequence injection: injected injected Figure 5–75: NEUTRAL IOC1 SCHEME LOGIC 5-172 F60 Feeder Protection System GE Multilin...
Page 305     (EQ 5.17) – The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents resulting from: • System unbalances under heavy load conditions. GE Multilin F60 Feeder Protection System 5-173...
Page 306 1.5 of a power system cycle. The element is designed to emulate an electromechanical directional device. Larger operating and polarizing signals results in faster directional discrimination bringing more security to the element operation. 5-174 F60 Feeder Protection System GE Multilin...
Page 307 The low-side system impedance should be assumed minimal when checking for this condition. A similar sit- uation arises for a wye/delta/wye transformer, where current in one transformer winding neutral may reverse when faults on both sides of the transformer are considered. GE Multilin F60 Feeder Protection System 5-175...
Page 308 NEUTRAL DIR OC1 REV PICKUP: This setting defines the pickup level for the overcurrent unit of the element in the reverse direction. When selecting this setting it must be kept in mind that the design uses a positive-sequence restraint technique for the “Calculated 3I0” mode of operation. 5-176 F60 Feeder Protection System GE Multilin...
Page 309 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–77: NEUTRAL DIRECTIONAL OVERCURRENT LOGIC GE Multilin F60 Feeder Protection System 5-177...
Page 310: Wattmetric Ground Fault
VT connected to the auxiliary channel bank of the relay). When the latter selection is made, the auxiliary channel must be identified by the user as a neutral voltage under the VT bank settings. This element operates when the auxil- iary voltage is configured as neutral. 5-178 F60 Feeder Protection System GE Multilin...
Page 311   FlexCurve --------- - (EQ 5.20)   Again, the FlexCurve timer starts after the definite time timer expires. GE Multilin F60 Feeder Protection System 5-179...
Page 312 SETTING 1 FUNCTION: WATTMETRIC GND FLT 1 Enabled = 1 OC PKP DEL: WATT GND FLT 1 BLK: FLEXLOGIC OPERAND Off = 0 WATTMETRIC 1 PKP 837033A4.CDR Figure 5–79: WATTMETRIC ZERO-SEQUENCE DIRECTIONAL LOGIC 5-180 F60 Feeder Protection System GE Multilin...
Page 313: Ground Current
This channel may be also equipped with a sensitive input. The conversion range of a sensitive channel is from 0.002 to 4.6 times the CT rating. NOTE Figure 5–80: GROUND TOC1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-181...
Page 314 This channel may be equipped with a standard or sensitive input. The conversion range of a sensitive channel is from 0.002 to 4.6 times the CT rating. NOTE Figure 5–81: GROUND IOC1 SCHEME LOGIC 5-182 F60 Feeder Protection System GE Multilin...
Page 315: Negative-Sequence Current
MESSAGE  The F60 relay provides two (2) negative-sequence time overcurrent elements, two (2) negative-sequence instantaneous overcurrent elements, and two (2) negative-sequence directional overcurrent elements. For additional information on the negative sequence time overcurrent curves, refer to the Inverse Time Overcurrent Curves section earlier.
Page 316 For example, if the element reset characteristic is set to “Instanta- neous” and the element is blocked, the time accumulator is cleared immediately. Figure 5–82: NEGATIVE SEQUENCE TOC1 SCHEME LOGIC 5-184 F60 Feeder Protection System GE Multilin...
Page 317 The operating quantity depends on the way the test currents are injected into the relay (single-phase injection:  0.2917 I ; three-phase injection, opposite rotation: injected injected Figure 5–83: NEGATIVE SEQUENCE IOC1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-185...
Page 318 The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious negative-sequence and zero-sequence currents resulting from: • System unbalances under heavy load conditions. • Transformation errors of current transformers (CTs). • Fault inception and switch-off transients. 5-186 F60 Feeder Protection System GE Multilin...
Page 319 CT errors, since the current is low. The operating quantity depends on the way the test currents are injected into the F60. For single phase injection: = ⅓  (1 – K  I •...
Page 320 The element characteristic angle in the reverse direction is the angle set for the forward direction shifted by 180°. • NEG SEQ DIR OC1 FWD LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit angle for the forward direction. 5-188 F60 Feeder Protection System GE Multilin...
Page 321 When NEG SEQ DIR OC1 TYPE selecting this setting it must be kept in mind that the design uses a positive-sequence restraint technique. Figure 5–85: NEGATIVE SEQUENCE DIRECTIONAL OC1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-189...
Page 322: Breaker Failure
Range: 0.001 to 30.000 pu in steps of 0.001 BF1 N AMP HISET MESSAGE PICKUP: 1.050 pu Range: 0.001 to 30.000 pu in steps of 0.001 BF1 PH AMP LOSET MESSAGE PICKUP: 1.050 pu 5-190 F60 Feeder Protection System GE Multilin...
Page 323 This can also occur in breaker-and-a-half or ring bus configurations where the first breaker closes into a fault; the protection trips and attempts to initiate breaker failure for the second breaker, which is in the process of closing, but does not yet have current flowing through it. GE Multilin F60 Feeder Protection System 5-191...
Page 324 BREAKER FAILURE TIMER No. 2 (±1/8 cycle) INITIATE (1/8 cycle) BREAKER FAILURE CURRENT DETECTOR PICKUP (1/8 cycle) BREAKER FAILURE OUTPUT RELAY PICKUP (1/4 cycle) FAULT cycles OCCURS 827083A6.CDR Figure 5–86: BREAKER FAILURE MAIN PATH SEQUENCE 5-192 F60 Feeder Protection System GE Multilin...
Page 325 In microprocessor relays this time is not significant. In F60 relays, which use a Fourier transform, the calculated current magnitude will ramp-down to zero one power frequency cycle after the current is interrupted, and this lag should be included in the overall margin duration, as it occurs after current interruption.
Page 326 Upon operation of the breaker failure element for a single pole trip command, a three-pole trip command should be given via output operand BKR FAIL 1 TRIP OP 5-194 F60 Feeder Protection System GE Multilin...
Page 327 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–88: SINGLE-POLE BREAKER FAILURE, INITIATE GE Multilin F60 Feeder Protection System 5-195...
Page 328 5.6 GROUPED ELEMENTS 5 SETTINGS Figure 5–89: SINGLE-POLE BREAKER FAILURE, TIMERS 5-196 F60 Feeder Protection System GE Multilin...
Page 329 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–90: THREE-POLE BREAKER FAILURE, INITIATE GE Multilin F60 Feeder Protection System 5-197...
Page 330 5.6 GROUPED ELEMENTS 5 SETTINGS Figure 5–91: THREE-POLE BREAKER FAILURE, TIMERS 5-198 F60 Feeder Protection System GE Multilin...
Page 331: Voltage Elements
The time delay is adjustable from 0 to 600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay char- acteristic. GE Multilin F60 Feeder Protection System 5-199...
Page 332 V = secondary voltage applied to the relay = pickup level pickup % of voltage pickup 842788A1.CDR Figure 5–92: INVERSE TIME UNDERVOLTAGE CURVES At 0% of pickup, the operating time equals the UNDERVOLTAGE DELAY setting. NOTE 5-200 F60 Feeder Protection System GE Multilin...
Page 333 The minimum voltage setting selects the operating voltage below which the element is blocked (a setting of “0” will allow a dead source to be considered a fault condition). Figure 5–93: PHASE UNDERVOLTAGE1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-201...
Page 334 FLEXLOGIC OPERAND PHASE OV1 PKP 827066A7.CDR Figure 5–94: PHASE OVERVOLTAGE SCHEME LOGIC   If the source VT is wye-connected, then the phase overvoltage pickup condition is Pickup for V and V NOTE 5-202 F60 Feeder Protection System GE Multilin...
Page 335 “Definite time”. The source assigned to this element must be configured for a phase VT. NEUTRAL OV1 CURVE VT errors and normal voltage unbalance must be considered when setting this element. This function requires the VTs to be wye-connected. Figure 5–95: NEUTRAL OVERVOLTAGE1 SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-203...
Page 336 The negative-sequence overvoltage element may be used to detect loss of one or two phases of the source, a reversed phase sequence of voltage, or a non-symmetrical system voltage condition. Figure 5–96: NEGATIVE-SEQUENCE OVERVOLTAGE SCHEME LOGIC 5-204 F60 Feeder Protection System GE Multilin...
Page 337 AUX UV1 EVENTS: MESSAGE Disabled The F60 contains one auxiliary undervoltage element for each VT bank. This element is intended for monitoring undervolt- age conditions of the auxiliary voltage. The selects the voltage level at which the time undervoltage ele- AUX UV1 PICKUP ment starts timing.
Page 338 AUX OV1 EVENTS: MESSAGE Disabled The F60 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM ...
Page 339: Sensitive Directional Power
The operating quantity is displayed in the   actual ACTUAL VALUES METERING SENSITIVE DIRECTIONAL POWER 1(2) value. The element has two independent (as to the pickup and delay settings) stages for alarm and trip, respectively. GE Multilin F60 Feeder Protection System 5-207...
Page 340 RCA = 0 SMIN < 0 SMIN > 0 OPERATE RESTRAIN RESTRAIN OPERATE RCA = 90 RCA = 270 SMIN > 0 SMIN < 0 842702A1.CDR Figure 5–100: DIRECTIONAL POWER ELEMENT SAMPLE APPLICATIONS 5-208 F60 Feeder Protection System GE Multilin...
Page 341 DIR POWER 1 OP Three-phase reactive power (Q) DIR POWER 1 STG2 DPO DIR POWER 1 STG2 OP SETTING DIR POWER 1 STG2 DELAY: 100 ms 842003A3.CDR Figure 5–101: SENSITIVE DIRECTIONAL POWER SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-209...
Page 342: Overview
If more than one operate-type operand is required, it may be assigned directly from the trip bus menu. 5-210 F60 Feeder Protection System GE Multilin...
Page 343 TRIP BUS 1 PKP = Enabled TRIP BUS 1 BLOCK = Off SETTINGS TRIP BUS 1 LATCHING = Enabled TRIP BUS 1 RESET = Off FLEXLOGIC OPERAND RESET OP 842023A1.CDR Figure 5–103: TRIP BUS LOGIC GE Multilin F60 Feeder Protection System 5-211...
Page 344: Setting Groups
The setting groups menu controls the activation and deactivation of up to six possible groups of settings in the GROUPED settings menu. The faceplate Settings In Use LEDs indicate which active group (with a non-flashing energized ELEMENTS LED) is in service. 5-212 F60 Feeder Protection System GE Multilin...
Page 345 CONT IP 1 ON (H5A) OR (2) AND (3) = VIRT OP 1 (VO1) PHASE TOC1 PKP PHASE TOC2 PKP AND (3) = VIRT OP 1 (VO1) 842789A1.CDR Figure 5–104: EXAMPLE FLEXLOGIC CONTROL OF A SETTINGS GROUP GE Multilin F60 Feeder Protection System 5-213...
Page 346: Selector Switch
1 to the . If the control word is outside the range, an alarm is established SELECTOR FULL RANGE by setting the FlexLogic operand for 3 seconds. SELECTOR ALARM 5-214 F60 Feeder Protection System GE Multilin...
Page 347 SELECTOR 1 3BIT ACK: This setting specifies an acknowledging input for the three-bit control input. The pre- selected position is applied on the rising edge of the assigned FlexLogic operand. This setting is active only under the GE Multilin F60 Feeder Protection System 5-215...
Page 348 The selector position pre-selected via the stepping up control input has not been confirmed before the time out. SELECTOR 1 BIT ALARM The selector position pre-selected via the three-bit control input has not been confirmed before the time out. 5-216 F60 Feeder Protection System GE Multilin...
Page 349 3BIT A1 3BIT A2 POS 1 POS 2 POS 3 POS 4 POS 5 POS 6 POS 7 BIT 0 BIT 1 BIT 2 STP ALARM BIT ALARM ALARM 842737A1.CDR Figure 5–105: TIME-OUT MODE GE Multilin F60 Feeder Protection System 5-217...
Page 350 Make the following changes to selector switch element in the    SETTINGS CONTROL ELEMENTS SELECTOR SWITCH menu to assign control to user programmable pushbutton 1 and contact inputs 1 through 3: SELECTOR SWITCH 1 5-218 F60 Feeder Protection System GE Multilin...
Page 351 3-bit acknowledge SELECTOR 1 BIT ALARM 3-bit position out SELECTOR 1 ALARM SELECTOR 1 PWR ALARM SELECTOR 1 BIT 0 SELECTOR 1 BIT 1 SELECTOR 1 BIT 2 842012A2.CDR Figure 5–107: SELECTOR SWITCH LOGIC GE Multilin F60 Feeder Protection System 5-219...
Page 352: Underfrequency
For example, UNDERFREQ 1 PICKUP if the system frequency is 60 Hz and the load shedding is required at 59.5 Hz, the setting will be 59.50 Hz. Figure 5–108: UNDERFREQUENCY SCHEME LOGIC 5-220 F60 Feeder Protection System GE Multilin...
Page 353: Overfrequency
The setting selects OVERFREQ 1 SOURCE OVERFREQ 1 PICKUP the level at which the overfrequency element is to pickup. Figure 5–109: OVERFREQUENCY SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-221...
Page 354: Frequency Rate Of Change
FREQ RATE 1 OC SUPV PICKUP: This setting defines minimum current level required for operation of the element. The supervising function responds to the positive-sequence current. Typical application includes load shedding. Set the pickup threshold to zero if no overcurrent supervision is required. 5-222 F60 Feeder Protection System GE Multilin...
Page 355 SETTINGS FREQ RATE 1 PKP FREQ RATE 1 MIN FREQUENCY: FREQ RATE 1 MAX FREQUENCY: F > MIN & F < MAX Calculate df/dt 832023A2.CDR Figure 5–110: FREQUENCY RATE OF CHANGE SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-223...
Page 356: Synchrocheck
F. This time can be calculated by: ------------------------------- - (EQ 5.25) 360 ----------------- -  F 2   where: = phase angle difference in degrees; F = frequency difference in Hz. 5-224 F60 Feeder Protection System GE Multilin...
Page 357 (SOURCE Z) COMBINATION SOURCE Y SOURCE Z Phase VTs and Phase VTs and Phase Phase Auxiliary VT Auxiliary VT Phase VTs and Phase VT Phase Phase Auxiliary VT Phase VT Phase VT Phase Phase GE Multilin F60 Feeder Protection System 5-225...
Page 358 The relay will use the phase channel of a three-phase set of voltages if pro- grammed as part of that source. The relay will use the auxiliary voltage channel only if that channel is programmed as part of the Source and a three-phase set is not. 5-226 F60 Feeder Protection System GE Multilin...
Page 359 5 SETTINGS 5.7 CONTROL ELEMENTS Figure 5–111: SYNCHROCHECK SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-227...
Page 360: Autoreclose
4.000 s Range: FlexLogic operand AR1 ADD DELAY 1: MESSAGE Range: 0.00 to 655.35 s in steps of 0.01 AR1 DELAY 1: MESSAGE 0.000 s Range: FlexLogic operand AR1 ADD DELAY 2: MESSAGE 5-228 F60 Feeder Protection System GE Multilin...
Page 361 Scheme lockout blocks all phases of the reclosing cycle, preventing automatic reclosure, if any of the following occurs: • The maximum shot number was reached. • A ‘Block’ input is in effect (for instance; Breaker Failure, bus differential protection operated, etc.). GE Multilin F60 Feeder Protection System 5-229...
Page 362 ‘reclose-in-progress’ state. If all condi- tions allowing a breaker closure are not satisfied when this time expires, the scheme goes to “Lockout”. This timer must be set to a delay less than the reset timer. NOTE 5-230 F60 Feeder Protection System GE Multilin...
Page 363 5 SETTINGS 5.7 CONTROL ELEMENTS Figure 5–112: AUTORECLOSURE SCHEME LOGIC (Sheet 1 of 2) GE Multilin F60 Feeder Protection System 5-231...
Page 364 5.7 CONTROL ELEMENTS 5 SETTINGS Figure 5–113: AUTORECLOSURE SCHEME LOGIC (Sheet 2 of 2) 5-232 F60 Feeder Protection System GE Multilin...
Page 365 5 SETTINGS 5.7 CONTROL ELEMENTS Figure 5–114: SINGLE SHOT AUTORECLOSING SEQUENCE - PERMANENT FAULT GE Multilin F60 Feeder Protection System 5-233...
Page 366: Digital Elements
Some versions of the digital input modules include an active voltage monitor circuit connected across form-A contacts. The voltage monitor circuit limits the trickle current through the output circuit (see technical specifications for form-A). 5-234 F60 Feeder Protection System GE Multilin...
Page 367 The settings to use digital element 1 to monitor the breaker trip circuit are indicated below (EnerVista UR Setup example shown): The PICKUP DELAY setting should be greater than the operating time of the breaker to avoid nuisance alarms. NOTE GE Multilin F60 Feeder Protection System 5-235...
Page 368 “Off”. In this case, the settings are as follows (EnerVista UR Setup example shown). Figure 5–117: TRIP CIRCUIT EXAMPLE 2 The wiring connection for two examples above is applicable to both form-A contacts with voltage monitoring and solid-state contact with voltage monitoring. NOTE 5-236 F60 Feeder Protection System GE Multilin...
Page 369: Digital Counters
–2,147,483,648 counts, the counter will rollover to +2,147,483,647. • COUNTER 1 BLOCK: Selects the FlexLogic operand for blocking the counting operation. All counter operands are blocked. GE Multilin F60 Feeder Protection System 5-237...
Page 370 COUNTER 1 RESET: COUNTER 1 FROZEN: Off = 0 STORE DATE & TIME Date & Time SETTING COUNT1 FREEZE/RESET: Off = 0 827065A1.VSD SETTING COUNT1 FREEZE/COUNT: Off = 0 Figure 5–118: DIGITAL COUNTER SCHEME LOGIC 5-238 F60 Feeder Protection System GE Multilin...
Page 371: Monitoring Elements
HI-Z ARCING DET SOE MESSAGE RESET TIME: 0.0 s Range: 10 to 250 in steps of 1 HI-Z PHASE EVENT MESSAGE COUNT: Range: 10 to 500 in steps of 1 HI-Z GROUND EVENT MESSAGE COUNT: GE Multilin F60 Feeder Protection System 5-239...
Page 372 Captures triggered by loss of load and high arc confidence conditions are saved to a temporary capture table, and deleted if the event does not result in an Arcing or Downed Conductor condi- 5-240 F60 Feeder Protection System GE Multilin...
Page 373 Flag indicating the Spectral algorithm has found a match ThreePhaseFlag Flag indicating a three phase event was detected PhaseInfo[4] Phase specific information for the three phase currents and the neutral (see table below) GE Multilin F60 Feeder Protection System 5-241...
Page 374 Note that this is a minimum operating time; the actual operating time will depend on the fault characteristics and will likely be significantly longer than this setting. 5-242 F60 Feeder Protection System GE Multilin...
Page 375 “noise” on circuits with a moderate to high level of transient activ- ity. For the first three to five days after installation (or after being out-of-service for a significant period), the F60 may NOTE identify some of this noise as arcing.
Page 376 5.7 CONTROL ELEMENTS 5 SETTINGS Figure 5–119: HI-Z SCHEME LOGIC 5-244 F60 Feeder Protection System GE Multilin...
Page 377 • BKR 1 ARC AMP LIMIT: Selects the threshold value above which the output operand is set. GE Multilin F60 Feeder Protection System 5-245...
Page 378 Breaker Contacts Initiate Extinguished Part Total Area = Breaker Arcing Current (kA·cycle) Programmable 100 ms Start Delay Start Stop Integration Integration Figure 5–120: ARCING CURRENT MEASUREMENT Figure 5–121: BREAKER ARCING CURRENT SCHEME LOGIC 5-246 F60 Feeder Protection System GE Multilin...
Page 379 Breaker open, Voltage difference drop, and Measured flashover current through the breaker. Furthermore, the scheme is applicable for cases where either one or two sets of three-phase voltages are available across the breaker. GE Multilin F60 Feeder Protection System 5-247...
Page 380 This application does not require detection of breaker status via a 52a contact, as it uses a voltage difference larger than setting. However, monitoring the breaker contact will ensure scheme stability. BRK 1 FLSHOVR DIFF V PKP 5-248 F60 Feeder Protection System GE Multilin...
Page 381 BRK 1 FLSHOVR SPV A to BRK 1 FLSHOVR SPV C: These settings specify FlexLogic operands (per breaker pole) that supervise the operation of the element per phase. Supervision can be provided by operation of other protection GE Multilin F60 Feeder Protection System 5-249...
Page 382 BRK 1 FLSHOVR DIFF V SRC: PKP: SRC 1 SRC 2 SRC 6 , … , , none ΔVA > PKP Δ VA = VA - Va 842018A2.CDR Figure 5–122: BREAKER FLASHOVER SCHEME LOGIC 5-250 F60 Feeder Protection System GE Multilin...
Page 383 MESSAGE EVENTS: Disabled One breaker restrike element is provided in the F60. According to IEEE standard C37.100: IEEE Standard Definitions for Power Switchgear, restrike is defined as “a resumption of current between the contacts of a switching device during an opening operation after an interval of zero current of ¼...
Page 384 “1” when breaker is opened, either manually or from protection logic. • BRK RSTR 1 CLS CMD: This setting assigns a FlexLogic operand indicating a breaker close command. It must be logic “1” when breaker is closed. 5-252 F60 Feeder Protection System GE Multilin...
Page 385 Due to shortness of such spikes, they are not usually detected by the instantaneous protection of the feeder, which operates on the RMS or fundamental component of the phase current with a relatively high pickup. GE Multilin F60 Feeder Protection System 5-253...
Page 386 INCIPIENT FLT 1 TRIP COUNTS NUMBER: This setting selects the number of faults required to initiate a trip. • INCIPNT FLT 1 DETECT WINDOW: This setting specifies a time window for “Counts per window” mode of operation. 5-254 F60 Feeder Protection System GE Multilin...
Page 387 An additional condition is introduced to inhibit a fuse failure declaration when the monitored circuit is de-energized; positive- sequence voltage and current are both below threshold levels. setting enables and disables the fuse failure feature for each source. VT FUSE FAILURE 1 FUNCTION GE Multilin F60 Feeder Protection System 5-255...
Page 388 827093AQ.CDR Figure 5–128: VT FUSE FAIL SCHEME LOGIC Base voltage for this element is PHASE VT SECONDARY setting in the case of WYE VTs and (PHASE VT SECONDARY)/ in case of DELTA VTs. 5-256 F60 Feeder Protection System GE Multilin...
Page 389 • BROKEN CONDUCTOR 1 PKP DELAY: This setting specifies the pickup time delay for this function to operate after assertion of the broken conductor pickup FlexLogic operand. GE Multilin F60 Feeder Protection System 5-257...
Page 390 The cold curve characteristic is applied when the previous averaged load current over the last 5 cycles is less than 10% of the base current. If this current is greater or equal than 10% than the base current, then the hot curve characteristic is applied. 5-258 F60 Feeder Protection System GE Multilin...
Page 391     ---------------------------- -  (EQ 5.28)     – In the above equation, • τ = thermal protection trip time constant. • is a minimum reset time setting GE Multilin F60 Feeder Protection System 5-259...
Page 392 IEC255-8 cold curve or hot curve equations. op(In) • is the reset time calculated at index n as per the reset time equation. rst(In) • is the measured overload RMS current at index n. 5-260 F60 Feeder Protection System GE Multilin...
Page 393 30 minutes Busbar 60 minutes 20 minutes Underground cable 20 to 60 minutes 60 minutes The logic for the thermal overload protection element is shown below. Figure 5–131: THERMAL OVERLOAD PROTECTION SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-261...
Page 394: Cold Load Pickup
The reset delay interval is intended to be set to a period until the ON-LOAD TIME BEFORE RESET feeder load has decayed to normal levels, after which other features may be used to switch setting groups. 5-262 F60 Feeder Protection System GE Multilin...
Page 395 5 SETTINGS 5.7 CONTROL ELEMENTS Figure 5–133: COLD LOAD PICKUP SCHEME LOGIC GE Multilin F60 Feeder Protection System 5-263...
Page 396: Contact Inputs
The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user- settable debounce time in order for the F60 to validate the new contact state. In the figure below, the debounce time is set at 2.5 ms;...
Page 397 Event Records menu, make the following settings changes: "Breaker Closed (52b)" CONTACT INPUT H5A ID: "Enabled" CONTACT INPUT H5A EVENTS: Note that the 52b contact is closed when the breaker is open and open when the breaker is closed. GE Multilin F60 Feeder Protection System 5-265...
Page 398: Virtual Inputs
FlexLogic equation, it will likely have to be lengthened NOTE in time. A FlexLogic timer with a delayed reset can perform this function. Figure 5–135: VIRTUAL INPUTS SCHEME LOGIC 5-266 F60 Feeder Protection System GE Multilin...
Page 399: Contact Outputs
The most dependable protection of the initiating contact is provided by directly measuring current in the tripping circuit, and using this parameter to control resetting of the initiating relay. This scheme is often called trip seal-in. This can be realized in the F60 using the FlexLogic operand to seal-in the contact output as follows: CONT OP 1 ION “Cont Op 1"...
Page 400 5 SETTINGS The F60 latching output contacts are mechanically bi-stable and controlled by two separate (open and close) coils. As such they retain their position even if the relay is not powered up. The relay recognizes all latching output contact cards and pop- ulates the setting menu accordingly.
Page 401: Virtual Outputs
Logic equations. Any change of state of a virtual output can be logged as an event if programmed to do so. For example, if Virtual Output 1 is the trip signal from FlexLogic and the trip relay is used to signal events, the settings would be programmed as follows: GE Multilin F60 Feeder Protection System 5-269...
Page 402: Remote Devices
The remote input/output facility provides for 32 remote inputs and 64 remote outputs. b) LOCAL DEVICES: ID OF DEVICE FOR TRANSMITTING GSSE MESSAGES In a F60 relay, the device ID that represents the IEC 61850 GOOSE application ID (GoID) name string sent as part of each GOOSE message is programmed in the ...
Page 403: Remote Inputs
This setting identifies the Ethernet application identification in the GOOSE message. It should match the corre- sponding settings on the sending device. setting provides for the choice of the F60 fixed (DNA/UserSt) dataset (that is, containing REMOTE DEVICE 1 DATASET DNA and UserSt bit pairs), or one of the configurable datasets.
Page 404: Remote Double-Point Status Inputs
REMOTE OUTPUTS DNA BIT PAIRS REMOTE OUTPUTS DNA- 1(32) BIT PAIR Range: FlexLogic operand  REMOTE OUTPUTS DNA- 1 OPERAND:  DNA- 1 BIT PAIR Range: Disabled, Enabled DNA- 1 EVENTS: MESSAGE Disabled 5-272 F60 Feeder Protection System GE Multilin...
Page 405: Resetting
RESET OP to identify the source of the command. The setting RESET OP (PUSHBUTTON) RESET OP (COMMS) RESET OP (OPERAND) shown above selects the operand that will create the operand. RESET OP (OPERAND) GE Multilin F60 Feeder Protection System 5-273...
Page 406: Direct Inputs And Outputs
FlexLogic operand that determines the state of this direct output. c) APPLICATION EXAMPLES The examples introduced in the earlier Direct inputs and outputs section (part of the Product Setup section) are continued below to illustrate usage of the direct inputs and outputs. 5-274 F60 Feeder Protection System GE Multilin...
Page 407 5 SETTINGS 5.8 INPUTS/OUTPUTS EXAMPLE 1: EXTENDING INPUT/OUTPUT CAPABILITIES OF A F60 RELAY Consider an application that requires additional quantities of digital inputs or output contacts or lines of programmable logic that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED, such as the C30, to satisfy the additional inputs/outputs and programmable logic requirements.
Page 408 "3" (effectively, this is a message from IED 1) DIRECT INPUT 6 BIT NUMBER: UR IED 2: "1" DIRECT INPUT 5 DEVICE ID: "2" DIRECT INPUT 5 BIT NUMBER: "3" DIRECT INPUT 6 DEVICE ID: "2" DIRECT INPUT 6 BIT NUMBER: 5-276 F60 Feeder Protection System GE Multilin...
Page 409: Teleprotection Inputs And Outputs
Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-1 MESSAGE DEFAULT: Off Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-2 MESSAGE DEFAULT: Off  Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-16 MESSAGE DEFAULT: Off GE Multilin F60 Feeder Protection System 5-277...
Page 410 (teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel failure between any pair of relays. 5-278 F60 Feeder Protection System GE Multilin...
Page 411: Iec 61850 Goose Analogs
GOOSE ANALOG 1 PU: This setting specifies the per-unit base factor when using the GOOSE analog input FlexAna- log values in other F60 features, such as FlexElements. The base factor is applied to the GOOSE analog input FlexAn- alog quantity to normalize it to a per-unit quantity. The base units are described in the following table.
Page 412: Iec 61850 Goose Integers
= maximum primary RMS value of all the sources related to the +IN and –IN inputs BASE (Max Delta Volts) The GOOSE analog input FlexAnalog values are available for use in other F60 functions that use FlexAnalog values. 5.8.13 IEC 61850 GOOSE INTEGERS ...
Page 413: Dcma Inputs
–20 to +180 MW; in this case the value would be “–20” and the DCMA INPUT H1 MIN VALUE DCMA INPUT H1 MAX value “180”. Intermediate values between the min and max values are scaled linearly. VALUE GE Multilin F60 Feeder Protection System 5-281...
Page 414: Rtd Inputs
1.5 pu. FlexElement operands are available to FlexLogic for further interlocking or to operate an output contact directly. Refer to the following table for reference temperature values for each RTD type. 5-282 F60 Feeder Protection System GE Multilin...
Page 415 15.61 168.47 280.77 233.97 16.00 172.46 291.96 243.30 16.39 175.84 303.46 252.88 16.78 179.51 315.31 262.76 17.17 183.17 327.54 272.94 17.56 186.82 340.14 283.45 17.95 190.45 353.14 294.28 18.34 194.08 366.53 305.44 18.73 GE Multilin F60 Feeder Protection System 5-283...
Page 416: Dcma Outputs
– MAX VAL MIN VAL MAX VAL < 0.1 pu. The resulting characteristic is illustrated in the following figure. DRIVING SIGNAL MIN VAL MAX VAL 842739A1.CDR Figure 5–142: DCMA OUTPUT CHARACTERISTIC 5-284 F60 Feeder Protection System GE Multilin...
Page 417 The CT ratio is 5000:5 and the maximum load current is 4200 A. The current should be monitored from 0 A upwards, allow- ing for 50% overload. The phase current with the 50% overload margin is: GE Multilin F60 Feeder Protection System 5-285...
Page 418 254.03 kV 1.27 kV – • ±0.5% of reading For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is 0.005 x 230.94 kV + 1.27 kV = 2.42 kV. 5-286 F60 Feeder Protection System GE Multilin...
Page 419: Test Mode
TEST MODE FORCING: MESSAGE The F60 provides a test facility to verify the functionality of contact inputs and outputs, some communication channels and the phasor measurement unit (where applicable), using simulated conditions. The test mode is indicated on the relay face- plate by a Test Mode LED indicator.
Page 420: Force Contact Inputs
Following a restart, power up, settings TEST MODE FUNCTION upload, or firmware upgrade, the test mode will remain at the last programmed value. This allows a F60 that has been placed in isolated mode to remain isolated during testing and maintenance activities. On restart, the TEST MODE FORCING setting and the force contact input and force contact output settings all revert to their default states.
Page 421: Force Contact Outputs
PUSHBUTTON 1 FUNCTION input 1 to initiate the Test mode, make the following changes in the menu:   SETTINGS TESTING TEST MODE “Enabled” and “ ” TEST MODE FUNCTION: TEST MODE INITIATE: GE Multilin F60 Feeder Protection System 5-289...
Page 422: Phasor Measurement Unit Test Values
The relay must be in test mode to use the PMU test mode. That is, the  setting must be TESTING TEST MODE FUNCTION “Enabled” and the  initiating signal must be “On”. TESTING TEST MODE INITIATE 5-290 F60 Feeder Protection System GE Multilin...
Page 423 In test mode, the following actions take place: a. The Data Invalid / Test Mode bit (bit 15 in the STAT word) is set. b. The Sim bit in all output datasets is set. GE Multilin F60 Feeder Protection System 5-291...
Page 424 5.10 TESTING 5 SETTINGS 5-292 F60 Feeder Protection System GE Multilin...
Page 425: Actual Values Menu
  DIRECT DEVICES See page 6-10.  STATUS  IEC 61850 See page 6-10.  GOOSE UINTEGERS  EGD PROTOCOL See page 6-10.  STATUS  TELEPROT CH TESTS See page 6-11.  GE Multilin F60 Feeder Protection System...
Page 426  RTD INPUTS  ACTUAL VALUES  FAULT REPORTS See page 6-26.  RECORDS   EVENT RECORDS See page 6-26.   OSCILLOGRAPHY See page 6-27.   DATA LOGGER See page 6-27.  F60 Feeder Protection System GE Multilin...
Page 427  RECORDS  MAINTENANCE See page 6-28.   HIZ RECORDS See page 6-29.   ACTUAL VALUES  MODEL INFORMATION See page 6-30.  PRODUCT INFO   FIRMWARE REVISIONS See page 6-30.  GE Multilin F60 Feeder Protection System...
Page 428: Contact Inputs
The state displayed will be that of the remote point unless the remote device has been established to be “Offline” in which case the value shown is the programmed default state for the remote input. F60 Feeder Protection System GE Multilin...
Page 429: Remote Double-Point Status Inputs
The present state of the contact outputs is shown here. The first line of a message display indicates the ID of the contact output. For example, ‘Cont Op 1’ refers to the contact output in terms of the default name-array index. The second line of the display indicates the logic state of the contact output. GE Multilin F60 Feeder Protection System...
Page 430: Virtual Outputs
The present state of the programmed remote devices is shown here. The message indicates ALL REMOTE DEVICES ONLINE whether or not all programmed remote devices are online. If the corresponding state is "No", then at least one required remote device is not online. F60 Feeder Protection System GE Multilin...
Page 431: Digital Counters
Range: Current Position / 7 SELECTOR SWITCH 2 MESSAGE POSITION: 0/7 The display shows both the current position and the full range. The current position only (an integer from 0 through 7) is the actual value. GE Multilin F60 Feeder Protection System...
Page 432: Flex States
PTP grandmaster, this actual value is zero. The grandmasterIdentity code is specified by PTP to be globally unique, so one can always know which clock is grandmaster in a system with multiple grandmaster-capable clocks. F60 Feeder Protection System GE Multilin...
Page 433: Hi-Z Status
MESSAGE CH1: 0 AVG MSG RETURN MESSAGE TIME CH2: 0 ms UNRETURNED MSG MESSAGE COUNT CH2: 0 CRC FAIL COUNT MESSAGE CH2: 0 DIRECT INPUT MESSAGE DIRECT INPUT MESSAGE  DIRECT INPUT 32: MESSAGE GE Multilin F60 Feeder Protection System...
Page 434: Direct Devices Status
UINT INPUT 16 MESSAGE The F60 Feeder Protection System is provided with optional IEC 61850 communications capability. This feature is specified as a software option at the time of ordering. Refer to the Ordering section of chapter 2 for additional details.
Page 435: Teleprotection Channel Tests
PH A FAULTS: 0 Range: 0 to 65535 in steps of 1 INCIPIENT FAULT 1 MESSAGE PH B FAULTS: 0 Range: 0 to 65535 in steps of 1 INCIPIENT FAULT 1 MESSAGE PH C FAULTS: 0 GE Multilin F60 Feeder Protection System 6-11...
Page 436: Remaining Connection Status
LAN ID in the frame do not match). is a counter for total messages received with an error on Port B (PRP frame, but port received through MISMATCHES PORT B and LAN ID in the frame do not match). 6-12 F60 Feeder Protection System GE Multilin...
Page 437: Metering Conventions
PF = Lag WATTS = Negative VARS = Positive PF = Lead PF = Lag PF = Lead Current UR RELAY 827239AC.CDR S=VI Generator Figure 6–1: FLOW DIRECTION OF SIGNED VALUES FOR WATTS AND VARS GE Multilin F60 Feeder Protection System 6-13...
Page 438 -- - V   -- - V   -- - V   -- - V   -- - V   The above equations apply to currents as well. 6-14 F60 Feeder Protection System GE Multilin...
Page 439 The power system voltages are phase-referenced – for simplicity – to VAG and VAB, respectively. This, however, is a relative matter. It is important to remember that the F60 displays are always referenced as specified under SETTINGS ...
Page 440: Sources
0.000 SRC 1 RMS Ib: MESSAGE 0.000 SRC 1 RMS Ic: MESSAGE 0.000 SRC 1 RMS In: MESSAGE 0.000 SRC 1 PHASOR Ia: MESSAGE 0.000 0.0° SRC 1 PHASOR Ib: MESSAGE 0.000 0.0° 6-16 F60 Feeder Protection System GE Multilin...
Page 441 0.0° SRC 1 PHASOR Vbg: MESSAGE 0.000 0.0° SRC 1 PHASOR Vcg: MESSAGE 0.000 0.0° SRC 1 RMS Vab: MESSAGE 0.00 SRC 1 RMS Vbc: MESSAGE 0.00 SRC 1 RMS Vca: MESSAGE 0.00 GE Multilin F60 Feeder Protection System 6-17...
Page 442 REACTIVE PWR MESSAGE 3: 0.000 SRC 1 REACTIVE PWR MESSAGE a: 0.000 SRC 1 REACTIVE PWR MESSAGE b: 0.000 SRC 1 REACTIVE PWR MESSAGE c: 0.000 SRC 1 APPARENT PWR MESSAGE 3: 0.000 6-18 F60 Feeder Protection System GE Multilin...
Page 443 DMD IA:  SRC 1 0.000 SRC 1 DMD IA MAX: MESSAGE 0.000 SRC 1 DMD IA DATE: MESSAGE 2001/07/31 16:30:07 SRC 1 DMD IB: MESSAGE 0.000 SRC 1 DMD IB MAX: MESSAGE 0.000 GE Multilin F60 Feeder Protection System 6-19...
Page 444 The signal used for frequency estimation is low-pass filtered. The SYSTEM SETUP POWER SYSTEM final frequency measurement is passed through a validation filter that eliminates false readings due to signal distortions and transients. 6-20 F60 Feeder Protection System GE Multilin...
Page 445 The harmonics are a percentage of the fundamental signal obtained as a ratio of harmonic amplitude to fundamental ampli- tude multiplied by 100%. The total harmonic distortion (THD) is the ratio of the total harmonic content to the fundamental:  (EQ 6.2) GE Multilin F60 Feeder Protection System 6-21...
Page 446: Sensitive Directional Power
6.3 METERING 6 ACTUAL VALUES Voltage harmonics are not available on F60 relays configured with the high-impedance fault detection (Hi-Z) fea- ture. NOTE Voltage harmonics are calculated only for Wye connected phase VTs. Ensure the   SYSTEM SETUP AC INPUTS ...
Page 447: Frequency Rate Of Change
= maximum nominal primary RMS value of the +IN and –IN inputs BASE SYNCHROCHECK = maximum primary RMS value of all the sources related to the +IN and –IN inputs BASE (Max Delta Volts) GE Multilin F60 Feeder Protection System 6-23...
Page 448: Iec 61580 Goose Analog Values
ANALOG INPUT 32 MESSAGE 0.000 The F60 Feeder Protection System is provided with optional IEC 61850 communications capability. This feature is specified as a software option at the time of ordering. Refer to the Ordering section of chapter 2 for additional details.
Page 449: Pmu Aggregator
RTD INPUT xx  -50 °C Actual values for each RTD input channel that is enabled are displayed with the top line as the programmed channel ID and the bottom line as the value. GE Multilin F60 Feeder Protection System 6-25...
Page 450: Fault Reports
If all 1024 event records have been filled, the oldest record will be removed as a new record is added. Each event record shows the event identifier/sequence number, cause, and date/time stamp associated with the event trigger. Refer to the menu for clearing event records.  COMMANDS CLEAR RECORDS 6-26 F60 Feeder Protection System GE Multilin...
Page 451: Oscillography
It counts up at the defined sampling rate. If the data logger channels are defined, then both values are static. Refer to the  menu for clearing data logger records. COMMANDS CLEAR RECORDS GE Multilin F60 Feeder Protection System 6-27...
Page 452: Phasor Measurement Unit Records
BKR 1 ARCING AMP  menu for clearing breaker arcing current records. The COMMANDS CLEAR RECORDS BREAKER OPERATING TIME defined as the slowest operating time of breaker poles that were initiated to open. 6-28 F60 Feeder Protection System GE Multilin...
Page 453: Hi-Z Records
If the element is triggered by high impedance fault detection arcing algorithm, then the records are dis- RMS 4 played in the actual values. Refer to High impedance fault detection section in chapter 5 for more information. HIZ 1 HIZ 4 GE Multilin F60 Feeder Protection System 6-29...
Page 454: Model Information
6.5PRODUCT INFORMATION 6.5.1 MODEL INFORMATION   PATH: ACTUAL VALUES PRODUCT INFO MODEL INFORMATION Range: standard GE Multilin order code format;  MODEL INFORMATION ORDER CODE LINE 1: example order code shown  F60-E00-HCH-F8F-H6A Range: standard GE Multilin order code format...
Page 455: Virtual Inputs
The states of up to 64 virtual inputs are changed here. The first line of the display indicates the ID of the virtual input. The second line indicates the current or selected status of the virtual input. This status will be a state off (logic 0) or on (logic 1). GE Multilin F60 Feeder Protection System...
Page 456: Clear Records
“Yes” and pressing the ENTER key. After clearing data, the command setting automatically reverts to “No”. 7.1.4 SET DATE AND TIME  PATH: COMMANDS SET DATE AND TIME (YYYY/MM/DD HH:MM:SS)  COMMANDS SET DATE AND TIME:  SET DATE AND TIME 2000/01/14 13:47:03 F60 Feeder Protection System GE Multilin...
Page 457: Relay Maintenance
Various self-checking diagnostics are performed in the background while the F60 is running, and diagnostic information is stored on the non-volatile memory from time to time based on the self-checking result. Although the diagnostic information is cleared before the F60 is shipped from the factory, the user may want to clear the diagnostic information for themselves under certain circumstances.
Page 458 PMU and not to the absolute UTC time. Therefore a simple IRIG-B genera- tor could be used instead. Also, the test set does not have to support GPS synchronization. Any stable signal source can F60 Feeder Protection System GE Multilin...
Page 459: Security
Operator Logoff: Selecting ‘Yes’ allows the Supervisor to forcefully logoff an operator session. • Clear Security Data: Selecting ‘Yes’ allows the Supervisor to forcefully clear all the security logs and clears all the operands associated with the self-tests. GE Multilin F60 Feeder Protection System...
Page 460: Targets Menu
The critical fail relay on the power supply module is de-energized. • All other output relays are de-energized and are prevented from further operation. • The faceplate In Service LED indicator is turned off. • event is recorded. RELAY OUT OF SERVICE F60 Feeder Protection System GE Multilin...
Page 461 Contact Factory (xxx) • Latched target message: Yes. • Description of problem: One or more installed hardware modules is not compatible with the F60 order code. • How often the test is performed: Module dependent. • What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed mod- ule (for example, F8L).
Page 462 • What to do: Verify that all the items in the GOOSE data set are supported by the F60. The EnerVista UR Setup soft- ware will list the valid items. An IEC61850 client will also show which nodes are available for the F60.
Page 463 • How often the test is performed: Upon initiation of a contact output state change. • What to do: Verify the state of the output contact and contact the factory if the problem persists. GE Multilin F60 Feeder Protection System...
Page 464 Description of problem: The ambient temperature is greater than the maximum operating temperature (+80°C). • How often the test is performed: Every hour. • What to do: Remove the F60 from service and install in a location that meets operating temperature standards. UNEXPECTED RESTART: Press “RESET” key •...
Page 465 If this message appears, contact the factory and supply the failure code noted in the display. Text in the message identifies the failed module (for example, H81). If operated on a Process Card failure, the Module Fail self-test seals-in (latches) till the UR-series device is restarted. GE Multilin F60 Feeder Protection System 7-11...
Page 466 Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the faceplate reset key if the command has ended, however the output may still be non-functional. 7-12 F60 Feeder Protection System GE Multilin...
Page 467: Description
50 Hz system, it consists of a sum of the 25, 75, 125,..., 625 Hz components. If the Energy Algorithm detects a sudden, sustained increase in one of these component energies, it reports this to the Expert Arc Detector algorithm, resets itself, and continues to monitor for another sudden increase. GE Multilin F60 Feeder Protection System...
Page 468: Randomness Algorithm
F60 Feeder Protection System GE Multilin...
Page 469: Load Analysis Algorithm
The duration over which the algorithm inhibits the setting of the overcurrent flag(s) is from the time the even-harmonic level (as a percentage of RMS) increases above the threshold until one second after it falls back below the threshold. GE Multilin F60 Feeder Protection System...
Page 470: Hi-Z Voltage Supervision Algorithm
If one phase voltage shows a dip, the block is applied for all phases. Also the High Impedance Oscillography will record that a voltage dip was experienced. The Oscillography record is phase specific. F60 Feeder Protection System GE Multilin...
Page 471: Fault Type Determination
Depending on the fault type, appropriate voltage and current signals are selected from the phase quantities before applying the two equations above (the superscripts denote phases, the subscripts denote stations). For AG faults:  (EQ 8.7) GE Multilin F60 Feeder Protection System...
Page 472 -- - V (EQ 8.14) – – SYS0   Z -- - V – – SYS0 where Z is the equivalent zero-sequence impedance behind the relay as entered under the fault report setting menu. SYS0 F60 Feeder Protection System GE Multilin...
Page 473 FAULT TYPE FAULT FAULT LOCATION 3I_0 LOCATOR 1 FAULT# RECLOSE SHOT VA or VAB VB or VBC VC or VCA Vn or V_0 SHOT # FROM 827094A5.CDR AUTO RECLOSURE Figure 8–2: FAULT LOCATOR SCHEME GE Multilin F60 Feeder Protection System...
Page 474 8.2 FAULT LOCATOR 8 THEORY OF OPERATION F60 Feeder Protection System GE Multilin...
Page 475: Testing Underfrequency And Overfrequency Elements
Injection to a particular F60 frequency element must be to its configured source and to the channels the source uses for fre- quency measurement.
Page 476 1 second from test set time reading of ramp start to relay operation. Note that the F60 event records only show the “pickup delay” component, a definite time timer. This is exclusive of the time taken by the frequency responding component to pickup.
Page 477: Replace A Module
The enhanced faceplate can be opened to the left, once the thumb screw has been removed, as shown below. This allows for easy accessibility of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and allows easy access to all modules in the F60. 842812A1.CDR Figure 10–1: UR MODULE WITHDRAWAL AND INSERTION (ENHANCED FACEPLATE)
Page 478 The new CT/VT modules can only be used with new CPUs; similarly, old CT/VT modules can only be used with old CPUs. In the event that there is a mismatch between the CPU and CT/VT module, the relay does not function and error displays. NOTE DSP ERROR HARDWARE MISMATCH 10-2 F60 Feeder Protection System GE Multilin...
Page 479: Replace Battery
10. Reinstall the battery clip and the metal cover, and reinsert the power supply module into the unit. 11. Power on the unit. 12. Dispose of the old battery as outlined in the next section. GE Multilin F60 Feeder Protection System 10-3...
Page 480: Dispose Of Battery
La batterie est marqué de ce symbole, qui comprennent les indications cadmium (Cd), plomb (Pb), ou mercure (Hg). Pour le recyclage, retourner la batterie à votre fournisseur ou à un point de collecte. Pour plus d'informations, voir: www.recyclethis.info. 10-4 F60 Feeder Protection System GE Multilin...
Page 481 Baterija je označena s tem simbolom, ki lahko vključuje napise, ki označujejo kadmij (Cd), svinec (Pb) ali živo srebro (Hg). Za ustrezno recikliranje baterijo vrnite dobavitelju ali jo odstranite na določenem zbirališču. Za več informacij obiščite spletno stran: www.recyclethis.info. GE Multilin F60 Feeder Protection System 10-5...
Page 482 North America 905-294-6222 Latin America +55 11 3614 1700 Europe, Middle East, Africa +(34) 94 485 88 00 Asia +86-21-2401-3208 India +91 80 41314617 From GE Part Number 1604-0021-A1, GE Publication Number GEK-113574 10-6 F60 Feeder Protection System GE Multilin...
Page 483: A.1.1 Flexanalog Items
Source 1 positive-sequence current magnitude 6174 SRC 1 I_1 Angle Amps Source 1 positive-sequence current angle 6175 SRC 1 I_2 Mag Degrees Source 1 negative-sequence current magnitude 6177 SRC 1 I_2 Angle Amps Source 1 negative-sequence current angle GE Multilin F60 Feeder Protection System...
Page 484 Source 1 auxiliary voltage RMS 6688 SRC 1 Vx Mag Volts Source 1 auxiliary voltage magnitude 6690 SRC 1 Vx Angle Degrees Source 1 auxiliary voltage angle 6691 SRC 1 V_0 Mag Volts Source 1 zero-sequence voltage magnitude F60 Feeder Protection System GE Multilin...
Page 485 Source 1 phase C apparent power 7192 SRC 1 PF Source 1 three-phase power factor 7193 SRC 1 Phase A PF Source 1 phase A power factor 7194 SRC 1 Phase B PF Source 1 phase B power factor GE Multilin F60 Feeder Protection System...
Page 486 Volts Source 1 phase A voltage fourteenth harmonic 8078 SRC 1 Va Harm[13] Volts Source 1 phase A voltage fifteenth harmonic 8079 SRC 1 Va Harm[14] Volts Source 1 phase A voltage sixteenth harmonic F60 Feeder Protection System GE Multilin...
Page 487 Volts Source 1 phase C voltage eleventh harmonic 8125 SRC 1 Vc Harm[10] Volts Source 1 phase C voltage twelfth harmonic 8126 SRC 1 Vc Harm[11] Volts Source 1 phase C voltage thirteenth harmonic GE Multilin F60 Feeder Protection System...
Page 488 Volts Source 2 phase B voltage eighth harmonic 8172 SRC 2 Vb Harm[7] Volts Source 2 phase B voltage ninth harmonic 8173 SRC 2 Vb Harm[8] Volts Source 2 phase B voltage tenth harmonic F60 Feeder Protection System GE Multilin...
Page 489 HIZ Neutral Arc Conf High impedance fault detection neutral arc confidence 9024 Prefault Ia Mag [0] Amps Fault 1 pre-fault phase A current magnitude 9026 Prefault Ia Ang [0] Degrees Fault 1 pre-fault phase A current angle GE Multilin F60 Feeder Protection System...
Page 490 Volts Phasor measurement unit 1 positive-sequence voltage magnitude 9550 PMU 1 V1 Angle Degrees Phasor measurement unit 1 positive-sequence voltage angle 9551 PMU 1 V2 Mag Volts Phasor measurement unit 1 negative-sequence voltage magnitude F60 Feeder Protection System GE Multilin...
Page 491 Amps Source 1 phase A current twenty-fifth harmonic 10273 SRC 1 Ib THD Source 1 phase B current total harmonic distortion 10274 SRC 1 Ib Harm[0] Amps Source 1 phase B current second harmonic GE Multilin F60 Feeder Protection System...
Page 492 Source 1 phase C current twenty-second harmonic 10328 SRC 1 Ic Harm[21] Amps Source 1 phase C current twenty-third harmonic 10329 SRC 1 Ic Harm[22] Amps Source 1 phase C current twenty-fourth harmonic A-10 F60 Feeder Protection System GE Multilin...
Page 493 Source 2 phase B current nineteenth harmonic 10391 SRC 2 Ib Harm[18] Amps Source 2 phase B current twentieth harmonic 10392 SRC 2 Ib Harm[19] Amps Source 2 phase B current twenty-first harmonic GE Multilin F60 Feeder Protection System A-11...
Page 494 14 actual value 13532 DCMA Inputs 15 Value dcmA input 15 actual value 13534 DCMA Inputs 16 Value dcmA input 16 actual value 13536 DCMA Inputs 17 Value dcmA input 17 actual value A-12 F60 Feeder Protection System GE Multilin...
Page 495 RTD input 37 actual value 13589 RTD Inputs 38 Value RTD input 38 actual value 13590 RTD Inputs 39 Value RTD input 39 actual value 13591 RTD Inputs 40 Value RTD input 40 actual value GE Multilin F60 Feeder Protection System A-13...
Page 496 45602 GOOSE Analog In 10 IEC 61850 GOOSE analog input 10 45604 GOOSE Analog In 11 IEC 61850 GOOSE analog input 11 45606 GOOSE Analog In 12 IEC 61850 GOOSE analog input 12 A-14 F60 Feeder Protection System GE Multilin...
Page 497 HZ Ig Harmonics[23] Volts HIZ Ig harmonics 23 63291 HZ Ig Harmonics[24] Volts HIZ Ig harmonics 24 63292 HZ Ig Harmonics[25] Volts HIZ Ig harmonics 25 63293 HZ Ig Harmonics[26] Volts HIZ Ig harmonics 26 GE Multilin F60 Feeder Protection System A-15...
Page 498: A.1.2 Flexinteger Items
FLEXINTEGER NAME UNITS DESCRIPTION 9968 GOOSE UInt Input 1 IEC61850 GOOSE UInteger input 1 9970 GOOSE UInt Input 2 IEC61850 GOOSE UInteger input 2 9972 GOOSE UInt Input 3 IEC61850 GOOSE UInteger input 3 A-16 F60 Feeder Protection System GE Multilin...
Page 499 IEC61850 GOOSE UInteger input 13 9994 GOOSE UInt Input 14 IEC61850 GOOSE UInteger input 14 9996 GOOSE UInt Input 15 IEC61850 GOOSE UInteger input 15 9998 GOOSE UInt Input 16 IEC61850 GOOSE UInteger input 16 GE Multilin F60 Feeder Protection System A-17...
Page 500 A.1 PARAMETER LISTS APPENDIX A A-18 F60 Feeder Protection System GE Multilin...
Page 501: B.1.1 Introduction
Broadcast mode is only recognized when associated with function code 05h. For any other function code, a packet with broadcast mode slave address 0 will be ignored. GE Multilin F60 Feeder Protection System...
Page 502: B.1.4 Crc-16 Algorithm
No: go to 8; Yes: G (+) A --> A and continue. Is j = 8? No: go to 5; Yes: continue i + 1 --> i Is i = N? No: go to 3; Yes: continue A --> CRC F60 Feeder Protection System GE Multilin...
Page 503: B.2.1 Supported Function Codes
125. See the Modbus memory map table for exact details on the data registers. Since some PLC implementations of Modbus only support one of function codes 03h and 04h. The F60 interpretation allows either function code to be used for reading one or more consecutive data registers.
Page 504: B.2.3 Execute Operation (Function Code 05H)
DATA STARTING ADDRESS - low DATA STARTING ADDRESS - low DATA - high DATA - high DATA - low DATA - low CRC - low CRC - low CRC - high CRC - high F60 Feeder Protection System GE Multilin...
Page 505: B.2.5 Store Multiple Settings (Function Code 10H)
PACKET FORMAT EXAMPLE (HEX) SLAVE ADDRESS SLAVE ADDRESS FUNCTION CODE FUNCTION CODE CRC - low order byte ERROR CODE CRC - high order byte CRC - low order byte CRC - high order byte GE Multilin F60 Feeder Protection System...
Page 506: B.3.1 Obtaining Relay Files Via Modbus
Cleared Date to the present date and time. To read binary COMTRADE oscillography files, read the following filenames: OSCnnnn.CFG and OSCnnn.DAT Replace “nnn” with the desired oscillography trigger number. For ASCII format, use the following file names OSCAnnnn.CFG and OSCAnnn.DAT F60 Feeder Protection System GE Multilin...
Page 507 READING FAULT REPORT FILES Fault report data has been available via the F60 file retrieval mechanism since UR firmware version 2.00. The file name is faultReport#####.htm. The ##### refers to the fault report record number. The fault report number is a counter that indicates how many fault reports have ever occurred.
Page 508: B.3.2 Modbus Password Operation
When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 509: B.4.1 Modbus Memory Map
0 (Off) 0413 Virtual Input 20 State 0 to 1 F108 0 (Off) 0414 Virtual Input 21 State 0 to 1 F108 0 (Off) 0415 Virtual Input 22 State 0 to 1 F108 0 (Off) GE Multilin F60 Feeder Protection System...
Page 511 0 to 65535 F500 1605 Field shared input test states 0 to 65535 F500 1606 Field shared output operand states 0 to 65535 F500 1607 Field latching output open operand states 0 to 65535 F500 GE Multilin F60 Feeder Protection System B-11...
Page 512 Source 1 Phase B Current Angle -359.9 to 0 degrees F002 180E Source 1 Phase C Current Magnitude 0 to 999999.999 0.001 F060 1810 Source 1 Phase C Current Angle -359.9 to 0 degrees F002 B-12 F60 Feeder Protection System GE Multilin...
Page 513 -359.9 to 0 degrees F002 1A2C Reserved (20 items) F001 1A40 ...Repeated for Source 2 1A80 ...Repeated for Source 3 1AC0 ...Repeated for Source 4 1B00 ...Repeated for Source 5 1B40 ...Repeated for Source 6 GE Multilin F60 Feeder Protection System B-13...
Page 514 Frequency for Source 6 2 to 90 0.001 F003 Source Demand (Read Only) (6 modules) 1E00 Source 1 Demand Ia 0 to 999999.999 0.001 F060 1E02 Source 1 Demand Ib 0 to 999999.999 0.001 F060 B-14 F60 Feeder Protection System GE Multilin...
Page 515 0 to 4294967295 F300 21AA Breaker flashover 1 block 0 to 4294967295 F300 21AC Breaker flashover 1 events 0 to 1 F102 0 (Disabled) 21AD Breaker flashover 1 target 0 to 2 F109 0 (Self-Reset) GE Multilin F60 Feeder Protection System B-15...
Page 516 Hi-Z (High Impedance Fault Detection) RMS Records (Read Only) (4 modules) 2270 Hi-Z RMS Capture 1 Trigger Type 0 to 6 F188 0 (NONE) 2271 Hi-Z RMS Capture 1 Time 0 to 1 F050 B-16 F60 Feeder Protection System GE Multilin...
Page 517 6 (H1a) 2461 Field Raw Data Freeze 0 to 1 F102 0 (Disabled) Phasor Measurement Unit actual values (Read Only) (4 modules) 2540 PMU 1 Phase A Voltage Magnitude 0 to 999999.999 0.001 F060 GE Multilin F60 Feeder Protection System B-17...
Page 518 IEC 61850 GGIO5 uinteger input 4 operand F612 26B4 IEC 61850 GGIO5 uinteger input 5 operand F612 26B5 IEC 61850 GGIO5 uinteger input 6 operand F612 26B6 IEC 61850 GGIO5 uinteger input 7 operand F612 B-18 F60 Feeder Protection System GE Multilin...
Page 519 Oscillography Commands (Read/Write Command) 3005 Oscillography Force Trigger 0 to 1 F126 0 (No) 3011 Oscillography Clear Data 0 to 1 F126 0 (No) 3012 Oscillography Number of Triggers 0 to 32767 F001 GE Multilin F60 Feeder Protection System B-19...
Page 520 Settings Lock Alarm 0 to 1 F102 1 (Enabled) 3338 Bypass Access 0 to 1 F628 0 (Disabled) 3339 Encryption 0 to 1 F102 1 (Enabled) 333A Serial Inactivity Timeout 1 to 9999 F001 B-20 F60 Feeder Protection System GE Multilin...
Page 521 -32768 to 32767 °C F002 34F9 RTD Input 10 Value -32768 to 32767 °C F002 34FA RTD Input 11 Value -32768 to 32767 °C F002 34FB RTD Input 12 Value -32768 to 32767 °C F002 GE Multilin F60 Feeder Protection System B-21...
Page 522 0 to 65535 F001 1813 373F Undefined F619 0 (EAP-TTLS) 3740 Undefined 1 to 65535 F001 2910 3741 Undefined 0 to 9999 F001 3742 Undefined 0 to 9999 F001 3743 Undefined F002 (none) B-22 F60 Feeder Protection System GE Multilin...
Page 523 Remote Phase CT 1 Secondary 0 to 1 F123 0 (1 A) 3897 Remote Ground CT 1 Primary 1 to 65000 F001 3898 Remote Ground CT 1 Secondary 0 to 1 F123 0 (1 A) GE Multilin F60 Feeder Protection System B-23...
Page 525 Field Shared Output 1 Unit Dest 1 0 to 8 F256 0 (none) 3E39 Field Shared Output 1 Channel Dest 1 0 to 15 F001 3E3A Field Shared Output 1 Unit Dest 2 0 to 8 F256 0 (none) GE Multilin F60 Feeder Protection System B-25...
Page 527 DNP Client Addresses (2 items) 0 to 4294967295 F003 40A3 TCP Port Number for the Modbus protocol 0 to 65535 F001 40A4 TCP/UDP Port Number for the DNP Protocol 0 to 65535 F001 20000 GE Multilin F60 Feeder Protection System B-27...
Page 528 PRT1 GOOSE Enabled 0 to 1 F102 1 (Enabled) 4115 PRT2 GOOSE Enabled 0 to 1 F102 1 (Enabled) 4116 PRT3 GOOSE Enabled 0 to 1 F102 1 (Enabled) 4119 PRT2 PRP Mcst Addr F072 B-28 F60 Feeder Protection System GE Multilin...
Page 529 0 (No) Oscillography (Read/Write Setting) 41C0 Oscillography Number of Records 3 to 64 F001 41C1 Oscillography Trigger Mode 0 to 1 F118 0 (Auto. Overwrite) 41C2 Oscillography Trigger Position 0 to 100 F001 GE Multilin F60 Feeder Protection System B-29...
Page 531 Auxiliary VT 1 Connection 0 to 6 F166 1 (Vag) 4505 Auxiliary VT 1 Secondary 25 to 240 F001 4506 Auxiliary VT 1 Ratio 1 to 24000 F060 4508 ...Repeated for VT Bank 2 GE Multilin F60 Feeder Protection System B-31...
Page 532 0 to 4294967295 F300 47F0 Breaker 1 phase C opened 0 to 4294967295 F300 47F2 Breaker 1 operate time 0 to 65.535 0.001 F001 47F3 Breaker 1 events 0 to 1 F102 0 (Disabled) B-32 F60 Feeder Protection System GE Multilin...
Page 533 F002 4E15 Raw Field Data AC8 Mag 0 to 0.001 0.001 F003 4E17 Raw Field Data AC8 Angle 0 to 0.01 degree F002 4E18 Raw Field Data DC1 0 to 0.001 0.001 F002 GE Multilin F60 Feeder Protection System B-33...
Page 536 5B05 Neutral Time Overcurrent 1 Multiplier 0 to 600 0.01 F001 5B06 Neutral Time Overcurrent 1 Reset 0 to 1 F104 0 (Instantaneous) 5B07 Neutral Time Overcurrent 1 Block 0 to 4294967295 F300 B-36 F60 Feeder Protection System GE Multilin...
Page 537 Ground Instantaneous Overcurrent 1 Reset Delay 0 to 600 0.01 F001 5DA5 Ground Instantaneous Overcurrent 1 Block 0 to 4294967295 F300 5DA7 Ground Instantaneous Overcurrent 1 Target 0 to 2 F109 0 (Self-reset) GE Multilin F60 Feeder Protection System B-37...
Page 538 Autoreclose 1 Dead Time Shot 4 0 to 655.35 0.01 F001 6215 Autoreclose 1 Reset Lockout Delay 0 to 655.35 0.01 F001 6000 6216 Autoreclose 1 Reset Time 0 to 655.35 0.01 F001 6000 B-38 F60 Feeder Protection System GE Multilin...
Page 539 0 to 1 F102 0 (Disabled) 6471 Overfrequency 1 Block 0 to 4294967295 F300 6473 Overfrequency 1 Source 0 to 5 F167 0 (SRC 1) 6474 Overfrequency 1 Pickup 20 to 65 0.01 F001 6050 GE Multilin F60 Feeder Protection System B-39...
Page 541 Neg Seq Directional Overcurrent 1 Reverse Limit Angle 40 to 90 degrees F001 7267 Neg Sequence Directional Overcurrent 1 Reverse Pickup 0.015 to 30 0.05 F001 7268 Negative Sequence Directional Overcurrent 1 Target 0 to 2 F109 0 (Self-reset) GE Multilin F60 Feeder Protection System B-41...
Page 542 77B6 ...Repeated for Broken Conductor 2 Ohm Inputs (Read/Write Setting) (2 modules) 77F8 Ohm Inputs 1 Function 0 to 1 F102 0 (Disabled) 77F9 Ohm Inputs 1 ID F205 "Ohm Ip 1 " B-42 F60 Feeder Protection System GE Multilin...
Page 543 0 to 400000000 F050 Phasor Measurement Unit Network Reporting Configuration (Read/Write Setting) 7914 PMU Network Reporting Function 0 to 1 F102 0 (Disabled) 7915 PMU Network Reporting ID Code 1 to 65534 F001 GE Multilin F60 Feeder Protection System B-43...
Page 544 F001 7A0A Hi-Z Phase Rate of Change 1 to 999 A/2cycle F001 7A0B Hi-Z Neutral Rate of Change 1 to 999 A/2cycle F001 7A0C Hi-Z Loss of Load Threshold 5 to 100 F001 B-44 F60 Feeder Protection System GE Multilin...
Page 546 0 to 4294967295 F003 EGD Fast Production Status (Read Only Non-Volatile) 83E0 EGD Fast Producer Exchange 1 Signature 0 to 65535 F001 83E1 EGD Fast Producer Exchange 1 Configuration Time 0 to 4294967295 F003 B-46 F60 Feeder Protection System GE Multilin...
Page 547 F300 8629 Breaker Failure 1 Breaker Status 2 Phase B 0 to 4294967295 F300 862B Breaker Failure 1 Breaker Status 2 Phase C 0 to 4294967295 F300 862D ...Repeated for Breaker Failure 2 GE Multilin F60 Feeder Protection System B-47...
Page 552 On Load Time Before Reset 1 0 to 1000000 0.001 F003 100000 A008 Cold Load Pickup 1 Source 0 to 5 F167 0 (SRC 1) A009 Cold Load Pickup 1 Reserved 0 to 65535 F001 B-52 F60 Feeder Protection System GE Multilin...
Page 555 0 to 65534 F206 (none) AD2B IEC 61850 logical node MMXUx name prefix (6 items) 0 to 65534 F206 (none) AD3D IEC 61850 logical node GGIOx name prefix (5 items) 0 to 65534 F206 (none) GE Multilin F60 Feeder Protection System B-55...
Page 556 IEC 61850 GSSE ID F209 “GSSEOut” B03F IEC 61850 GOOSE Function (GoEna) 0 to 1 F102 0 (Disabled) B040 IEC 61850 GSSE Destination MAC Address F072 B043 IEC 61850 Standard GOOSE ID F209 “GOOSEOut” B-56 F60 Feeder Protection System GE Multilin...
Page 558 Wattmetric ground fault x Reserved 0 to 1 F001 B312 ...Repeated for wattmetric ground fault 2 B324 ...Repeated for wattmetric ground fault 3 B336 ...Repeated for wattmetric ground fault 4 B348 ...Repeated for wattmetric ground fault 5 B-58 F60 Feeder Protection System GE Multilin...
Page 559 Contact Input 1 Name F205 “Cont Ip 1“ BB06 Contact Input 1 Events 0 to 1 F102 0 (Disabled) BB07 Contact Input 1 Debounce Time 0 to 16 F001 BB08 ...Repeated for Contact Input 2 GE Multilin F60 Feeder Protection System B-59...
Page 564 Force VFD and LED 0 to 1 F126 0 (No) C432 Test Mode Initiate 0 to 4294967295 F300 Clear commands (read/write) C434 Clear All Relay Records Command 0 to 1 F126 0 (No) B-64 F60 Feeder Protection System GE Multilin...
Page 570 IEC 61850 GGIO2.CF.SPCSO11.ctlModel Value 0 to 2 F001 D32B IEC 61850 GGIO2.CF.SPCSO12.ctlModel Value 0 to 2 F001 D32C IEC 61850 GGIO2.CF.SPCSO13.ctlModel Value 0 to 2 F001 D32D IEC 61850 GGIO2.CF.SPCSO14.ctlModel Value 0 to 2 F001 B-70 F60 Feeder Protection System GE Multilin...
Page 571 0 to 2 F001 Remote Device Status (Read Only) (32 modules) D380 Remote Device 1 StNum 0 to 4294967295 F003 D382 Remote Device 1 SqNum 0 to 4294967295 F003 D384 ...Repeated for Remote Device 2 GE Multilin F60 Feeder Protection System B-71...
Page 572 Contact Output 1 Name F205 “Cont Op 1" DC96 Contact Output 1 Operation 0 to 4294967295 F300 DC98 Contact Output 1 Seal In 0 to 4294967295 F300 DC9A Latching Output 1 Reset 0 to 4294967295 F300 B-72 F60 Feeder Protection System GE Multilin...
Page 574 PMU Aggregator 1 PDC Network Control 0 to 1 F102 0 (Disabled) E247 Aggregator 1 Include PMU1 0 to 1 F126 0 (No) E248 Aggregator 1 Include PMU2 0 to 1 F126 0 (No) B-74 F60 Feeder Protection System GE Multilin...
Page 575 EC0E Synchrocheck 1 Block 0 to 4294967295 F300 EC10 Synchrocheck 1 Frequency Hysteresis 0 to 0.1 0.01 F001 EC11 ...Repeated for Synchrocheck 2 EC22 ...Repeated for Synchrocheck 3 EC33 ...Repeated for Synchrocheck 4 GE Multilin F60 Feeder Protection System B-75...
Page 576 Last settings change date 0 to 4294967295 F050 ED09 Template bitmask (750 items) 0 to 65535 F001 Phasor Measurement Unit Records (Read Only) EFFF PMU Recording Number of Triggers 0 to 65535 samples F001 B-76 F60 Feeder Protection System GE Multilin...
Page 577: B.4.2 Data Formats
0 = 1 & 3 Pole, 1 = 1 Pole, 2 = 3 Pole-A, 3 = 3 Pole-B Positive values indicate lagging power factor; negative values indicate leading. F083 ENUMERATION: SELECTOR MODES 0 = Time-Out, 1 = Acknowledge GE Multilin F60 Feeder Protection System B-77...
Page 578 0 = Disabled, 1 = Input 1, 2 = Input 2 3 = FlexCurve C 0 = 172 cycles, 1 = 336 cycles, 2 = 718 cycles, 3 = 159 cycles F117 ENUMERATION: NUMBER OF OSCILLOGRAPHY RECORDS B-78 F60 Feeder Protection System GE Multilin...
Page 579 Ground Instantaneous Overcurrent 1 0 = 1 A, 1 = 5 A Ground Instantaneous Overcurrent 2 Ground Instantaneous Overcurrent 3 Ground Instantaneous Overcurrent 4 Ground Instantaneous Overcurrent 5 Ground Instantaneous Overcurrent 6 Ground Instantaneous Overcurrent 7 GE Multilin F60 Feeder Protection System B-79...
Page 580 Non-volatile Latch 12 Autoreclose (three-pole) 1 Non-volatile Latch 13 Autoreclose (three-pole) 2 Non-volatile Latch 14 Autoreclose (three-pole) 3 Non-volatile Latch 15 Autoreclose (three-pole) 4 Non-volatile Latch 16 Autoreclose (three-pole) 5 Frequency Rate of Change 1 B-80 F60 Feeder Protection System GE Multilin...
Page 581 RTD Input 30 Digital Element 38 RTD Input 31 Digital Element 39 RTD Input 32 Digital Element 40 RTD Input 33 Digital Element 41 RTD Input 34 Digital Element 42 RTD Input 35 GE Multilin F60 Feeder Protection System B-81...
Page 582 0 = 31 x 8 cycles, 1 = 15 x 16 cycles, 2 = 7 x 32 cycles 3 = 3 x 64 cycles, 4 = 1 x 128 cycles F125 ENUMERATION: ACCESS LEVEL 0 = Restricted; 1 = Command, 2 = Setting, 3 = Factory Service B-82 F60 Feeder Protection System GE Multilin...
Page 583 A bit value of 0 = no error, 1 = error Brick Trouble Field RTD Trouble F144 Field TDR Trouble ENUMERATION: FORCED CONTACT INPUT STATE Remote Device Offline 0 = Disabled, 1 = Open, 2 = Closed Direct Device Offline GE Multilin F60 Feeder Protection System B-83...
Page 584 System Integrity Recovery System Integrity Recovery 06 System Integrity Recovery 07 F155 ENUMERATION: REMOTE DEVICE STATE 0 = Offline, 1 = Online F147 ENUMERATION: LINE LENGTH UNITS 0 = km, 1 = miles B-84 F60 Feeder Protection System GE Multilin...
Page 585 0 = A, 1 = B, 2 = C ENUMERATION: AUXILIARY VT CONNECTION TYPE 0 = Vn, 1 = Vag, 2 = Vbg, 3 = Vcg, 4 = Vab, 5 = Vbc, 6 = Vca GE Multilin F60 Feeder Protection System B-85...
Page 586 0 = Phase to Ground, 1 = Phase to Phase ENUMERATION: HI-Z STATE bitmask definition F187 LOSS OF LOAD ENUMERATION: HI-Z STATES ARCING SUSPECTED ARCING bitmask Hi-Z State OVERCURRENT NORMAL DOWNED CONDUCTOR COORDINAT ION TIMEOUT EXTERNAL ARMED ARCING DOWNED CONDUCTOR B-86 F60 Feeder Protection System GE Multilin...
Page 587 F191 TEXT12: 12-CHARACTER ASCII TEXT ENUMERATION: HI-Z ENERGY/RANDOM STATE bitmask HI-Z Energy/Random State F206 REINSTATE TEXT6: 6-CHARACTER ASCII TEXT INITSTATE NORMALSTATE F207 EVENTSTATE TEXT4: 4-CHARACTER ASCII TEXT SERIOUSSTATE F208 TEXT2: 2-CHARACTER ASCII TEXT GE Multilin F60 Feeder Protection System B-87...
Page 588 0 = None, 1 = Keypad, 2 = Front Port, 3 = COM1, 4 = COM2, 5 = MMXU1.MX.W.phsC.cVal.mag.f Ethernet MMXU1.MX.VAr.phsA.cVal.mag.f MMXU1.MX.VAr.phsB.cVal.mag.f F230 MMXU1.MX.VAr.phsC.cVal.mag.f ENUMERATION: DIRECTIONAL POLARIZING MMXU1.MX.VA.phsA.cVal.mag.f 0 = Voltage, 1 = Current, 2 = Dual, 3 = Dual-V, 4 = Dual-I MMXU1.MX.VA.phsB.cVal.mag.f MMXU1.MX.VA.phsC.cVal.mag.f MMXU1.MX.PF.phsA.cVal.mag.f MMXU1.MX.PF.phsB.cVal.mag.f B-88 F60 Feeder Protection System GE Multilin...
Page 589 MMXU4.MX.PhV.phsB.cVal.ang.f MMXU2.MX.PF.phsC.cVal.mag.f MMXU4.MX.PhV.phsC.cVal.mag.f MMXU3.MX.TotW.mag.f MMXU4.MX.PhV.phsC.cVal.ang.f MMXU3.MX.TotVAr.mag.f MMXU4.MX.A.phsA.cVal.mag.f MMXU3.MX.TotVA.mag.f MMXU4.MX.A.phsA.cVal.ang.f MMXU3.MX.TotPF.mag.f MMXU4.MX.A.phsB.cVal.mag.f MMXU3.MX.Hz.mag.f MMXU4.MX.A.phsB.cVal.ang.f MMXU3.MX.PPV.phsAB.cVal.mag.f MMXU4.MX.A.phsC.cVal.mag.f MMXU3.MX.PPV.phsAB.cVal.ang.f MMXU4.MX.A.phsC.cVal.ang.f MMXU3.MX.PPV.phsBC.cVal.mag.f MMXU4.MX.A.neut.cVal.mag.f MMXU3.MX.PPV.phsBC.cVal.ang.f MMXU4.MX.A.neut.cVal.ang.f MMXU3.MX.PPV.phsCA.cVal.mag.f MMXU4.MX.W.phsA.cVal.mag.f MMXU3.MX.PPV.phsCA.cVal.ang.f MMXU4.MX.W.phsB.cVal.mag.f MMXU3.MX.PhV.phsA.cVal.mag.f MMXU4.MX.W.phsC.cVal.mag.f MMXU3.MX.PhV.phsA.cVal.ang.f MMXU4.MX.VAr.phsA.cVal.mag.f MMXU3.MX.PhV.phsB.cVal.mag.f MMXU4.MX.VAr.phsB.cVal.mag.f MMXU3.MX.PhV.phsB.cVal.ang.f MMXU4.MX.VAr.phsC.cVal.mag.f GE Multilin F60 Feeder Protection System B-89...
Page 590 GGIO4.MX.AnIn10.mag.f MMXU5.MX.VA.phsA.cVal.mag.f GGIO4.MX.AnIn11.mag.f MMXU5.MX.VA.phsB.cVal.mag.f GGIO4.MX.AnIn12.mag.f MMXU5.MX.VA.phsC.cVal.mag.f GGIO4.MX.AnIn13.mag.f MMXU5.MX.PF.phsA.cVal.mag.f GGIO4.MX.AnIn14.mag.f MMXU5.MX.PF.phsB.cVal.mag.f GGIO4.MX.AnIn15.mag.f MMXU5.MX.PF.phsC.cVal.mag.f GGIO4.MX.AnIn16.mag.f MMXU6.MX.TotW.mag.f GGIO4.MX.AnIn17.mag.f MMXU6.MX.TotVAr.mag.f GGIO4.MX.AnIn18.mag.f MMXU6.MX.TotVA.mag.f GGIO4.MX.AnIn19.mag.f MMXU6.MX.TotPF.mag.f GGIO4.MX.AnIn20.mag.f MMXU6.MX.Hz.mag.f GGIO4.MX.AnIn21.mag.f MMXU6.MX.PPV.phsAB.cVal.mag.f GGIO4.MX.AnIn22.mag.f MMXU6.MX.PPV.phsAB.cVal.ang.f GGIO4.MX.AnIn23.mag.f MMXU6.MX.PPV.phsBC.cVal.mag.f GGIO4.MX.AnIn24.mag.f MMXU6.MX.PPV.phsBC.cVal.ang.f GGIO4.MX.AnIn25.mag.f MMXU6.MX.PPV.phsCA.cVal.mag.f GGIO4.MX.AnIn26.mag.f B-90 F60 Feeder Protection System GE Multilin...
Page 591 ENUMERATION: CONFIGURABLE GOOSE DATASET ITEMS GGIO3.ST.UIntIn3.stVal FOR RECEPTION GGIO3.ST.UIntIn4.q value GOOSE dataset item GGIO3.ST.UIntIn4.stVal None GGIO3.ST.UIntIn5.q GGIO3.ST.Ind1.q GGIO3.ST.UIntIn5.stVal GGIO3.ST.Ind1.stVal GGIO3.ST.UIntIn6.q GGIO3.ST.Ind2.q GGIO3.ST.UIntIn6.stVal GGIO3.ST.Ind2.stVal GGIO3.ST.UIntIn7.q   GGIO3.ST.UIntIn7.stVal GGIO1.ST.Ind64q GGIO3.ST.UIntIn8.q GGIO1.ST.Ind64.stVal GGIO3.ST.UIntIn8.stVal GGIO3.MX.AnIn1.mag.f GGIO3.ST.UIntIn9.q GE Multilin F60 Feeder Protection System B-91...
Page 592 ENUMERATION: REAL TIME CLOCK MONTH Value Function value month Disabled January Isolated February Forcible March April F254 ENUMERATION: INCIPIENT CABLE FAULT MODE June July Value Function August Number of Counts September Counts per Window October November December B-92 F60 Feeder Protection System GE Multilin...
Page 593 17 to 32 (if required) The third register indicates [4] VIRTUAL INPUTS (1 to 32) input/output state with bits 0 to 15 corresponding to input/output [6] VIRTUAL OUTPUTS (1 to 64 GE Multilin F60 Feeder Protection System B-93...
Page 594 F523 BITFIELD: 3-PHASE SIMPLE ELEMENT STATE ENUMERATION: DNP OBJECTS 20, 22, AND 23 DEFAULT VARIATION 0 = Operate, 1 = Operate A, 2 = Operate B, 3 = Operate C bitmask default variation B-94 F60 Feeder Protection System GE Multilin...
Page 595 Only certain values may be used as Flex- 0 = None, 1 = Symm-3-Point, 2 = Symm-5-Point, Analogs (basically all metering quantities used in protection). 3 = Symm-7-Point, 4 = Class M, 5 = Class P GE Multilin F60 Feeder Protection System B-95...
Page 596 IEC 61850 report dataset items PIOC12.ST.Op.general None PIOC13.ST.Str.general PDIF1.ST.Str.general PIOC13.ST.Op.general PDIF1.ST.Op.general PIOC14.ST.Str.general PDIF2.ST.Str.general PIOC14.ST.Op.general PDIF2.ST.Op.general PIOC15.ST.Str.general PDIF3.ST.Str.general PIOC15.ST.Op.general PDIF3.ST.Op.general PIOC16.ST.Str.general PDIF4.ST.Str.general PIOC16.ST.Op.general PDIF4.ST.Op.general PIOC17.ST.Str.general PDIS1.ST.Str.general PIOC17.ST.Op.general PDIS1.ST.Op.general PIOC18.ST.Str.general PDIS2.ST.Str.general PIOC18.ST.Op.general PDIS2.ST.Op.general PIOC19.ST.Str.general PDIS3.ST.Str.general PIOC19.ST.Op.general B-96 F60 Feeder Protection System GE Multilin...
Page 597 PIOC64.ST.Op.general PIOC38.ST.Op.general PIOC65.ST.Str.general PIOC39.ST.Str.general PIOC65.ST.Op.general PIOC39.ST.Op.general PIOC66.ST.Str.general PIOC40.ST.Str.general PIOC66.ST.Op.general PIOC40.ST.Op.general PIOC67.ST.Str.general PIOC41.ST.Str.general PIOC67.ST.Op.general PIOC41.ST.Op.general PIOC68.ST.Str.general PIOC42.ST.Str.general PIOC68.ST.Op.general PIOC42.ST.Op.general PIOC69.ST.Str.general PIOC43.ST.Str.general PIOC69.ST.Op.general PIOC43.ST.Op.general PIOC70.ST.Str.general PIOC44.ST.Str.general PIOC70.ST.Op.general PIOC44.ST.Op.general PIOC71.ST.Str.general PIOC45.ST.Str.general PIOC71.ST.Op.general PIOC45.ST.Op.general PIOC72.ST.Str.general PIOC46.ST.Str.general PIOC72.ST.Op.general GE Multilin F60 Feeder Protection System B-97...
Page 598 PTUV5.ST.Op.general PTOC19.ST.Op.general PTUV6.ST.Str.general PTOC20.ST.Str.general PTUV6.ST.Op.general PTOC20.ST.Op.general PTUV7.ST.Str.general PTOC21.ST.Str.general PTUV7.ST.Op.general PTOC21.ST.Op.general PTUV8.ST.Str.general PTOC22.ST.Str.general PTUV8.ST.Op.general PTOC22.ST.Op.general PTUV9.ST.Str.general PTOC23.ST.Str.general PTUV9.ST.Op.general PTOC23.ST.Op.general PTUV10.ST.Str.general PTOC24.ST.Str.general PTUV10.ST.Op.general PTOC24.ST.Op.general PTUV11.ST.Str.general PTOV1.ST.Str.general PTUV11.ST.Op.general PTOV1.ST.Op.general PTUV12.ST.Str.general PTOV2.ST.Str.general PTUV12.ST.Op.general PTOV2.ST.Op.general PTUV13.ST.Str.general PTOV3.ST.Str.general PTUV13.ST.Op.general B-98 F60 Feeder Protection System GE Multilin...
Page 599 CSWI11.ST.Pos.stVal RBRF19.ST.OpIn.general CSWI12.ST.Loc.stVal RBRF20.ST.OpEx.general CSWI12.ST.Pos.stVal RBRF20.ST.OpIn.general CSWI13.ST.Loc.stVal RBRF21.ST.OpEx.general CSWI13.ST.Pos.stVal RBRF21.ST.OpIn.general CSWI14.ST.Loc.stVal RBRF22.ST.OpEx.general CSWI14.ST.Pos.stVal RBRF22.ST.OpIn.general CSWI15.ST.Loc.stVal RBRF23.ST.OpEx.general CSWI15.ST.Pos.stVal RBRF23.ST.OpIn.general CSWI16.ST.Loc.stVal RBRF24.ST.OpEx.general CSWI16.ST.Pos.stVal RBRF24.ST.OpIn.general CSWI17.ST.Loc.stVal RFLO1.MX.FltDiskm.mag.f CSWI17.ST.Pos.stVal RFLO2.MX.FltDiskm.mag.f CSWI18.ST.Loc.stVal RFLO3.MX.FltDiskm.mag.f CSWI18.ST.Pos.stVal RFLO4.MX.FltDiskm.mag.f CSWI19.ST.Loc.stVal RFLO5.MX.FltDiskm.mag.f CSWI19.ST.Pos.stVal GE Multilin F60 Feeder Protection System B-99...
Page 600 GGIO1.ST.Ind68.stVal GGIO1.ST.Ind16.stVal GGIO1.ST.Ind69.stVal GGIO1.ST.Ind17.stVal GGIO1.ST.Ind70.stVal GGIO1.ST.Ind18.stVal GGIO1.ST.Ind71.stVal GGIO1.ST.Ind19.stVal GGIO1.ST.Ind72.stVal GGIO1.ST.Ind20.stVal GGIO1.ST.Ind73.stVal GGIO1.ST.Ind21.stVal GGIO1.ST.Ind74.stVal GGIO1.ST.Ind22.stVal GGIO1.ST.Ind75.stVal GGIO1.ST.Ind23.stVal GGIO1.ST.Ind76.stVal GGIO1.ST.Ind24.stVal GGIO1.ST.Ind77.stVal GGIO1.ST.Ind25.stVal GGIO1.ST.Ind78.stVal GGIO1.ST.Ind26.stVal GGIO1.ST.Ind79.stVal GGIO1.ST.Ind27.stVal GGIO1.ST.Ind80.stVal GGIO1.ST.Ind28.stVal GGIO1.ST.Ind81.stVal GGIO1.ST.Ind29.stVal GGIO1.ST.Ind82.stVal GGIO1.ST.Ind30.stVal GGIO1.ST.Ind83.stVal GGIO1.ST.Ind31.stVal GGIO1.ST.Ind84.stVal B-100 F60 Feeder Protection System GE Multilin...
Page 601 MMXU2.MX.PPV.phsBC.cVal.ang.f GGIO1.ST.Ind122.stVal MMXU2.MX.PPV.phsCA.cVal.mag.f GGIO1.ST.Ind123.stVal MMXU2.MX.PPV.phsCA.cVal.ang.f GGIO1.ST.Ind124.stVal MMXU2.MX.PhV.phsA.cVal.mag.f GGIO1.ST.Ind125.stVal MMXU2.MX.PhV.phsA.cVal.ang.f GGIO1.ST.Ind126.stVal MMXU2.MX.PhV.phsB.cVal.mag.f GGIO1.ST.Ind127.stVal MMXU2.MX.PhV.phsB.cVal.ang.f GGIO1.ST.Ind128.stVal MMXU2.MX.PhV.phsC.cVal.mag.f MMXU1.MX.TotW.mag.f MMXU2.MX.PhV.phsC.cVal.ang.f MMXU1.MX.TotVAr.mag.f MMXU2.MX.A.phsA.cVal.mag.f MMXU1.MX.TotVA.mag.f MMXU2.MX.A.phsA.cVal.ang.f MMXU1.MX.TotPF.mag.f MMXU2.MX.A.phsB.cVal.mag.f MMXU1.MX.Hz.mag.f MMXU2.MX.A.phsB.cVal.ang.f MMXU1.MX.PPV.phsAB.cVal.mag.f MMXU2.MX.A.phsC.cVal.mag.f MMXU1.MX.PPV.phsAB.cVal.ang.f MMXU2.MX.A.phsC.cVal.ang.f MMXU1.MX.PPV.phsBC.cVal.mag.f MMXU2.MX.A.neut.cVal.mag.f MMXU1.MX.PPV.phsBC.cVal.ang.f MMXU2.MX.A.neut.cVal.ang.f GE Multilin F60 Feeder Protection System B-101...
Page 602 MMXU5.MX.TotPF.mag.f MMXU3.MX.W.phsA.cVal.mag.f MMXU5.MX.Hz.mag.f MMXU3.MX.W.phsB.cVal.mag.f MMXU5.MX.PPV.phsAB.cVal.mag.f MMXU3.MX.W.phsC.cVal.mag.f MMXU5.MX.PPV.phsAB.cVal.ang.f MMXU3.MX.VAr.phsA.cVal.mag.f MMXU5.MX.PPV.phsBC.cVal.mag.f MMXU3.MX.VAr.phsB.cVal.mag.f MMXU5.MX.PPV.phsBC.cVal.ang.f MMXU3.MX.VAr.phsC.cVal.mag.f MMXU5.MX.PPV.phsCA.cVal.mag.f MMXU3.MX.VA.phsA.cVal.mag.f MMXU5.MX.PPV.phsCA.cVal.ang.f MMXU3.MX.VA.phsB.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.mag.f MMXU3.MX.VA.phsC.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.ang.f MMXU3.MX.PF.phsA.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.mag.f MMXU3.MX.PF.phsB.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.ang.f MMXU3.MX.PF.phsC.cVal.mag.f MMXU5.MX.PhV.phsC.cVal.mag.f MMXU4.MX.TotW.mag.f MMXU5.MX.PhV.phsC.cVal.ang.f MMXU4.MX.TotVAr.mag.f MMXU5.MX.A.phsA.cVal.mag.f MMXU4.MX.TotVA.mag.f MMXU5.MX.A.phsA.cVal.ang.f MMXU4.MX.TotPF.mag.f MMXU5.MX.A.phsB.cVal.mag.f B-102 F60 Feeder Protection System GE Multilin...
Page 603 XSWI2.ST.Pos.stVal MMXU6.MX.A.phsB.cVal.ang.f XSWI3.ST.Loc.stVal MMXU6.MX.A.phsC.cVal.mag.f XSWI3.ST.Pos.stVal MMXU6.MX.A.phsC.cVal.ang.f XSWI4.ST.Loc.stVal MMXU6.MX.A.neut.cVal.mag.f XSWI4.ST.Pos.stVal MMXU6.MX.A.neut.cVal.ang.f XSWI5.ST.Loc.stVal MMXU6.MX.W.phsA.cVal.mag.f XSWI5.ST.Pos.stVal MMXU6.MX.W.phsB.cVal.mag.f XSWI6.ST.Loc.stVal MMXU6.MX.W.phsC.cVal.mag.f XSWI6.ST.Pos.stVal MMXU6.MX.VAr.phsA.cVal.mag.f XSWI7.ST.Loc.stVal MMXU6.MX.VAr.phsB.cVal.mag.f XSWI7.ST.Pos.stVal MMXU6.MX.VAr.phsC.cVal.mag.f XSWI8.ST.Loc.stVal MMXU6.MX.VA.phsA.cVal.mag.f XSWI8.ST.Pos.stVal MMXU6.MX.VA.phsB.cVal.mag.f XSWI9.ST.Loc.stVal MMXU6.MX.VA.phsC.cVal.mag.f XSWI9.ST.Pos.stVal MMXU6.MX.PF.phsA.cVal.mag.f XSWI10.ST.Loc.stVal MMXU6.MX.PF.phsB.cVal.mag.f XSWI10.ST.Pos.stVal GE Multilin F60 Feeder Protection System B-103...
Page 604 GGIO1.ST.Ind24.q GGIO1.ST.Ind24.stVal GGIO1.ST.Ind25.q F616 GGIO1.ST.Ind25.stVal ENUMERATION: IEC 61850 GOOSE DATASET ITEMS GGIO1.ST.Ind26.q Enumeration GOOSE dataset items GGIO1.ST.Ind26.stVal None GGIO1.ST.Ind27.q GGIO1.ST.Ind1.q GGIO1.ST.Ind27.stVal GGIO1.ST.Ind1.stVal GGIO1.ST.Ind28.q GGIO1.ST.Ind2.q GGIO1.ST.Ind28.stVal GGIO1.ST.Ind2.stVal GGIO1.ST.Ind29.q GGIO1.ST.Ind3.q GGIO1.ST.Ind29.stVal GGIO1.ST.Ind3.stVal GGIO1.ST.Ind30.q GGIO1.ST.Ind4.q GGIO1.ST.Ind30.stVal B-104 F60 Feeder Protection System GE Multilin...
Page 605 GGIO1.ST.Ind75.stVal GGIO1.ST.Ind49.stVal GGIO1.ST.Ind76.q GGIO1.ST.Ind50.q GGIO1.ST.Ind76.stVal GGIO1.ST.Ind50.stVal GGIO1.ST.Ind77.q GGIO1.ST.Ind51.q GGIO1.ST.Ind77.stVal GGIO1.ST.Ind51.stVal GGIO1.ST.Ind78.q GGIO1.ST.Ind52.q GGIO1.ST.Ind78.stVal GGIO1.ST.Ind52.stVal GGIO1.ST.Ind79.q GGIO1.ST.Ind53.q GGIO1.ST.Ind79.stVal GGIO1.ST.Ind53.stVal GGIO1.ST.Ind80.q GGIO1.ST.Ind54.q GGIO1.ST.Ind80.stVal GGIO1.ST.Ind54.stVal GGIO1.ST.Ind81.q GGIO1.ST.Ind55.q GGIO1.ST.Ind81.stVal GGIO1.ST.Ind55.stVal GGIO1.ST.Ind82.q GGIO1.ST.Ind56.q GGIO1.ST.Ind82.stVal GGIO1.ST.Ind56.stVal GGIO1.ST.Ind83.q GGIO1.ST.Ind57.q GGIO1.ST.Ind83.stVal GE Multilin F60 Feeder Protection System B-105...
Page 606 GGIO1.ST.Ind128.stVal GGIO1.ST.Ind102.stVal MMXU1.MX.TotW.mag.f GGIO1.ST.Ind103.q MMXU1.MX.TotVAr.mag.f GGIO1.ST.Ind103.stVal MMXU1.MX.TotVA.mag.f GGIO1.ST.Ind104.q MMXU1.MX.TotPF.mag.f GGIO1.ST.Ind104.stVal MMXU1.MX.Hz.mag.f GGIO1.ST.Ind105.q MMXU1.MX.PPV.phsAB.cVal.mag.f GGIO1.ST.Ind105.stVal MMXU1.MX.PPV.phsAB.cVal.ang.f GGIO1.ST.Ind106.q MMXU1.MX.PPV.phsBC.cVal.mag.f GGIO1.ST.Ind106.stVal MMXU1.MX.PPV.phsBC.cVal.ang.f GGIO1.ST.Ind107.q MMXU1.MX.PPV.phsCA.cVal.mag.f GGIO1.ST.Ind107.stVal MMXU1.MX.PPV.phsCA.cVal.ang.f GGIO1.ST.Ind108.q MMXU1.MX.PhV.phsA.cVal.mag.f GGIO1.ST.Ind108.stVal MMXU1.MX.PhV.phsA.cVal.ang.f GGIO1.ST.Ind109.q MMXU1.MX.PhV.phsB.cVal.mag.f GGIO1.ST.Ind109.stVal MMXU1.MX.PhV.phsB.cVal.ang.f GGIO1.ST.Ind110.q MMXU1.MX.PhV.phsC.cVal.mag.f B-106 F60 Feeder Protection System GE Multilin...
Page 607 MMXU3.MX.VA.phsA.cVal.mag.f MMXU2.MX.PhV.phsC.cVal.ang.f MMXU3.MX.VA.phsB.cVal.mag.f MMXU2.MX.A.phsA.cVal.mag.f MMXU3.MX.VA.phsC.cVal.mag.f MMXU2.MX.A.phsA.cVal.ang.f MMXU3.MX.PF.phsA.cVal.mag.f MMXU2.MX.A.phsB.cVal.mag.f MMXU3.MX.PF.phsB.cVal.mag.f MMXU2.MX.A.phsB.cVal.ang.f MMXU3.MX.PF.phsC.cVal.mag.f MMXU2.MX.A.phsC.cVal.mag.f MMXU4.MX.TotW.mag.f MMXU2.MX.A.phsC.cVal.ang.f MMXU4.MX.TotVAr.mag.f MMXU2.MX.A.neut.cVal.mag.f MMXU4.MX.TotVA.mag.f MMXU2.MX.A.neut.cVal.ang.f MMXU4.MX.TotPF.mag.f MMXU2.MX.W.phsA.cVal.mag.f MMXU4.MX.Hz.mag.f MMXU2.MX.W.phsB.cVal.mag.f MMXU4.MX.PPV.phsAB.cVal.mag.f MMXU2.MX.W.phsC.cVal.mag.f MMXU4.MX.PPV.phsAB.cVal.ang.f MMXU2.MX.VAr.phsA.cVal.mag.f MMXU4.MX.PPV.phsBC.cVal.mag.f MMXU2.MX.VAr.phsB.cVal.mag.f MMXU4.MX.PPV.phsBC.cVal.ang.f MMXU2.MX.VAr.phsC.cVal.mag.f MMXU4.MX.PPV.phsCA.cVal.mag.f MMXU2.MX.VA.phsA.cVal.mag.f MMXU4.MX.PPV.phsCA.cVal.ang.f GE Multilin F60 Feeder Protection System B-107...
Page 608 MMXU6.MX.W.phsB.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.mag.f MMXU6.MX.W.phsC.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.ang.f MMXU6.MX.VAr.phsA.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.mag.f MMXU6.MX.VAr.phsB.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.ang.f MMXU6.MX.VAr.phsC.cVal.mag.f MMXU5.MX.PhV.phsC.cVal.mag.f MMXU6.MX.VA.phsA.cVal.mag.f MMXU5.MX.PhV.phsC.cVal.ang.f MMXU6.MX.VA.phsB.cVal.mag.f MMXU5.MX.A.phsA.cVal.mag.f MMXU6.MX.VA.phsC.cVal.mag.f MMXU5.MX.A.phsA.cVal.ang.f MMXU6.MX.PF.phsA.cVal.mag.f MMXU5.MX.A.phsB.cVal.mag.f MMXU6.MX.PF.phsB.cVal.mag.f MMXU5.MX.A.phsB.cVal.ang.f MMXU6.MX.PF.phsC.cVal.mag.f MMXU5.MX.A.phsC.cVal.mag.f GGIO4.MX.AnIn1.mag.f MMXU5.MX.A.phsC.cVal.ang.f GGIO4.MX.AnIn2.mag.f MMXU5.MX.A.neut.cVal.mag.f GGIO4.MX.AnIn3.mag.f MMXU5.MX.A.neut.cVal.ang.f GGIO4.MX.AnIn4.mag.f MMXU5.MX.W.phsA.cVal.mag.f GGIO4.MX.AnIn5.mag.f MMXU5.MX.W.phsB.cVal.mag.f GGIO4.MX.AnIn6.mag.f B-108 F60 Feeder Protection System GE Multilin...
Page 609 PIOC2.ST.Op.general GGIO5.ST.UIntIn6.stVal PIOC3.ST.Str.general GGIO5.ST.UIntIn7.q PIOC3.ST.Op.general GGIO5.ST.UIntIn7.stVal PIOC4.ST.Str.general GGIO5.ST.UIntIn8.q PIOC4.ST.Op.general GGIO5.ST.UIntIn8.stVal PIOC5.ST.Str.general GGIO5.ST.UIntIn9.q PIOC5.ST.Op.general GGIO5.ST.UIntIn9.stVal PIOC6.ST.Str.general GGIO5.ST.UIntIn10.q PIOC6.ST.Op.general GGIO5.ST.UIntIn10.stVal PIOC7.ST.Str.general GGIO5.ST.UIntIn11.q PIOC7.ST.Op.general GGIO5.ST.UIntIn11.stVal PIOC8.ST.Str.general GGIO5.ST.UIntIn12.q PIOC8.ST.Op.general GGIO5.ST.UIntIn12.stVal PIOC9.ST.Str.general GGIO5.ST.UIntIn13.q PIOC9.ST.Op.general GGIO5.ST.UIntIn13.stVal PIOC10.ST.Str.general GGIO5.ST.UIntIn14.q PIOC10.ST.Op.general GE Multilin F60 Feeder Protection System B-109...
Page 610 PIOC55.ST.Op.general PIOC29.ST.Op.general PIOC56.ST.Str.general PIOC30.ST.Str.general PIOC56.ST.Op.general PIOC30.ST.Op.general PIOC57.ST.Str.general PIOC31.ST.Str.general PIOC57.ST.Op.general PIOC31.ST.Op.general PIOC58.ST.Str.general PIOC32.ST.Str.general PIOC58.ST.Op.general PIOC32.ST.Op.general PIOC59.ST.Str.general PIOC33.ST.Str.general PIOC59.ST.Op.general PIOC33.ST.Op.general PIOC60.ST.Str.general PIOC34.ST.Str.general PIOC60.ST.Op.general PIOC34.ST.Op.general PIOC61.ST.Str.general PIOC35.ST.Str.general PIOC61.ST.Op.general PIOC35.ST.Op.general PIOC62.ST.Str.general PIOC36.ST.Str.general PIOC62.ST.Op.general PIOC36.ST.Op.general PIOC63.ST.Str.general PIOC37.ST.Str.general PIOC63.ST.Op.general B-110 F60 Feeder Protection System GE Multilin...
Page 611 PTRC2.ST.Op.general PTOC10.ST.Op.general PTRC3.ST.Tr.general PTOC11.ST.Str.general PTRC3.ST.Op.general PTOC11.ST.Op.general PTRC4.ST.Tr.general PTOC12.ST.Str.general PTRC4.ST.Op.general PTOC12.ST.Op.general PTRC5.ST.Tr.general PTOC13.ST.Str.general PTRC5.ST.Op.general PTOC13.ST.Op.general PTRC6.ST.Tr.general PTOC14.ST.Str.general PTRC6.ST.Op.general PTOC14.ST.Op.general PTUV1.ST.Str.general PTOC15.ST.Str.general PTUV1.ST.Op.general PTOC15.ST.Op.general PTUV2.ST.Str.general PTOC16.ST.Str.general PTUV2.ST.Op.general PTOC16.ST.Op.general PTUV3.ST.Str.general PTOC17.ST.Str.general PTUV3.ST.Op.general PTOC17.ST.Op.general PTUV4.ST.Str.general PTOC18.ST.Str.general PTUV4.ST.Op.general GE Multilin F60 Feeder Protection System B-111...
Page 612 CSWI2.ST.Pos.stVal RBRF10.ST.OpIn.general CSWI3.ST.Loc.stVal RBRF11.ST.OpEx.general CSWI3.ST.Pos.stVal RBRF11.ST.OpIn.general CSWI4.ST.Loc.stVal RBRF12.ST.OpEx.general CSWI4.ST.Pos.stVal RBRF12.ST.OpIn.general CSWI5.ST.Loc.stVal RBRF13.ST.OpEx.general CSWI5.ST.Pos.stVal RBRF13.ST.OpIn.general CSWI6.ST.Loc.stVal RBRF14.ST.OpEx.general CSWI6.ST.Pos.stVal RBRF14.ST.OpIn.general CSWI7.ST.Loc.stVal RBRF15.ST.OpEx.general CSWI7.ST.Pos.stVal RBRF15.ST.OpIn.general CSWI8.ST.Loc.stVal RBRF16.ST.OpEx.general CSWI8.ST.Pos.stVal RBRF16.ST.OpIn.general CSWI9.ST.Loc.stVal RBRF17.ST.OpEx.general CSWI9.ST.Pos.stVal RBRF17.ST.OpIn.general CSWI10.ST.Loc.stVal RBRF18.ST.OpEx.general CSWI10.ST.Pos.stVal B-112 F60 Feeder Protection System GE Multilin...
Page 613 CSWI30.ST.Loc.stVal 1000 XCBR2.ST.Pos.stVal CSWI30.ST.Pos.stVal 1001 XCBR3.ST.Loc.stVal XSWI1.ST.Loc.stVal 1002 XCBR3.ST.Pos.stVal XSWI1.ST.Pos.stVal 1003 XCBR4.ST.Loc.stVal XSWI2.ST.Loc.stVal 1004 XCBR4.ST.Pos.stVal XSWI2.ST.Pos.stVal 1005 XCBR5.ST.Loc.stVal XSWI3.ST.Loc.stVal 1006 XCBR5.ST.Pos.stVal XSWI3.ST.Pos.stVal 1007 XCBR6.ST.Loc.stVal XSWI4.ST.Loc.stVal 1008 XCBR6.ST.Pos.stVal XSWI4.ST.Pos.stVal XSWI5.ST.Loc.stVal XSWI5.ST.Pos.stVal XSWI6.ST.Loc.stVal XSWI6.ST.Pos.stVal XSWI7.ST.Loc.stVal GE Multilin F60 Feeder Protection System B-113...
Page 614 Mode 4 (3 Pole - B) rity on local access, remoted access, or both) Enumeration Item F623 Disabled ENUMERATION: RTC SYNCHRONIZING SOURCE CONFIGU- Local and Remote RATION Local Enumeration Item Remote None PP/IRIG-B/PTP/SNTP IRIG-B/PP/PTP/SNTP PP/PTP/IRIG-B/SNTP B-114 F60 Feeder Protection System GE Multilin...
Page 615: C.1.1 Introduction
LAN environment. Actual MMS protocol services are mapped to IEC 61850 abstract ser- vices in IEC 61850-8-1. The F60 relay supports IEC 61850 server services over TCP/IP. The TCP/IP profile requires the F60 to have an IP address to establish communications. These addresses are located in the ...
Page 616: C.2.1 Overview
C.2.2 GGIO1: DIGITAL STATUS VALUES The GGIO1 logical node is available in the F60 to provide access to as many 128 digital status points and associated time- stamps and quality flags. The data content must be configured before the data can be used. GGIO1 provides digital status points for access by clients.
Page 617: C.2.6 Mmxu: Analog Measured Values
A limited number of measured analog values are available through the MMXU logical nodes. Each MMXU logical node provides data from a F60 current and voltage source. There is one MMXU available for each con- figurable source (programmed in the ...
Page 618 The protection elements listed above contain start (pickup) and operate flags. For example, the start flag for PIOC1 is PIOC1.ST.Str.general. The operate flag for PIOC1 is PIOC1.ST.Op.general. For the F60 protection elements, these flags take their values from the pickup and operate FlexLogic operands for the corresponding element.
Page 619: C.3.1 Buffered/Unbuffered Reporting
C.3.4 LOGICAL DEVICE NAME The logical device name is used to identify the IEC 61850 logical device that exists within the F60. This name is composed of two parts: the IED name setting and the logical device instance. The complete logical device name is the combination of the two character strings programmed in the settings.
Page 620: C.3.6 Logical Node Name Prefixes
A built-in TCP/IP connection timeout of two minutes is employed by the F60 to detect ‘dead’ connections. If there is no data traffic on a TCP connection for greater than two minutes, the connection will be aborted by the F60. This frees up the con- nection to be used by other clients.
Page 621: C.4.1 Overview
MAC address for GSSE messages. If GSSE DESTINATION MAC ADDRESS a valid multicast Ethernet MAC address is not entered (for example, 00 00 00 00 00 00), the F60 will use the source Ether- net MAC address as the destination, with the multicast bit set.
Page 622 The F60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station components.
Page 623 REMOTE IN 1 ITEM item to remote input 1. Remote input 1 can now be used in FlexLogic equations or other settings. The F60 must be rebooted (control power removed and re-applied) before these settings take effect. The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value in the sending device.
Page 624: C.4.5 Ethernet Mac Address For Gsse/Goose
GSSE and GOOSE messages must have multicast destination MAC addresses. By default, the F60 is configured to use an automated multicast MAC scheme. If the F60 destination MAC address setting is not a valid multicast address (that is, the least significant bit of the first byte is not set), the address used as the destina- tion MAC will be the same as the local MAC address, but with the multicast bit set.
Page 625: C.5.1 Overview
An ICD file is generated for the F60 by the EnerVista UR Setup software that describe the capabilities of the IED. The ICD file is then imported into a system configurator along with other ICD files for other IEDs (from GE or other ven- dors) for system configuration.
Page 626: C.5.2 Configuring Iec 61850 Settings
Transmission GOOSE dataset may be added or deleted, or prefixes of some logical nodes may be changed. While all new configurations will be mapped to the F60 settings file when importing an SCD file, all unchanged settings will preserve the same values in the new settings file.
Page 627: C.5.3 About Icd Files
Although configurable transmission GOOSE can also be created and altered by some third-party system con- figurators, we recommend configuring transmission GOOSE for GE Multilin IEDs before creating the ICD, and strictly within EnerVista UR Setup software or the front panel display (access through the Settings > Product Setup > Com- munications >...
Page 628 Furthermore, it defines the capabilities of an IED in terms of communication services offered and, together with its LNType, instantiated data (DO) and its default or configuration values. There should be only one IED section in an ICD since it only describes one IED. C-14 F60 Feeder Protection System GE Multilin...
Page 629 RptEnabled Other ReportControl elements DOI (name) SDI (name) DAI (name) Text Other DOI elements SDI (name) DAI (name) Text Other LN elements Other LDevice elements 842797A1.CDR Figure C–4: ICD FILE STRUCTURE, IED NODE GE Multilin F60 Feeder Protection System C-15...
Page 630 BDA (name, bType, type) Other BDA elements Other BDA elements Other DAType elements Other DAType elements EnumType (id) Text EnumVal (ord) Other EnumVal elements Other EnumType elements 842798A1.CDR Figure C–5: ICD FILE STRUCTURE, DATATYPETEMPLATES NODE C-16 F60 Feeder Protection System GE Multilin...
Page 631: C.5.4 Creating An Icd File With Enervista Ur Setup
The EnerVista UR Setup will prompt to save the file. Select the file path and enter the name for the ICD file, then click OK to generate the file. The time to create an ICD file from the offline F60 settings file is typically much quicker than create an ICD file directly from the relay.
Page 632 Like ICD files, the Header node identifies the SCD file and its version, and specifies options for the mapping of names to signals. The Substation node describes the substation parameters: Substation PowerSystemResource EquipmentContainer Power Transformer GeneralEquipment EquipmentContainer VoltageLevel Voltage PowerSystemResource Function SubFunction GeneralEquipment 842792A1.CDR Figure C–7: SCD FILE STRUCTURE, SUBSTATION NODE C-18 F60 Feeder Protection System GE Multilin...
Page 633 IdInst is the instance identification of the logical device within the IED on which the control block is located, and cbName is the name of the control block. GE Multilin F60 Feeder Protection System C-19...
Page 634: C.5.6 Importing An Scd File With Enervista Ur Setup
Figure C–9: SCD FILE STRUCTURE, IED NODE C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP The following procedure describes how to update the F60 with the new configuration from an SCD file with the EnerVista UR Setup software. Right-click anywhere in the files panel and select the Import Contents From SCD File item.
Page 635 The software will open the SCD file and then prompt the user to save a UR-series settings file. Select a location and name for the URS (UR-series relay settings) file. If there is more than one GE Multilin IED defined in the SCD file, the software prompt the user to save a UR-series set- tings file for each IED.
Page 636: C.6.1 Acsi Basic Conformance Statement
Setting group control REPORTING Buffered report control M7-1 sequence-number M7-2 report-time-stamp M7-3 reason-for-inclusion M7-4 data-set-name M7-5 data-reference M7-6 buffer-overflow M7-7 entryID M7-8 BufTm M7-9 IntgPd M7-10 Unbuffered report control M8-1 sequence-number M8-2 report-time-stamp M8-3 reason-for-inclusion C-22 F60 Feeder Protection System GE Multilin...
Page 637: C.6.3 Acsi Services Conformance Statement
SERVER/ UR FAMILY PUBLISHER SERVER (CLAUSE 7) ServerDirectory APPLICATION ASSOCIATION (CLAUSE 8) Associate Abort Release LOGICAL DEVICE (CLAUSE 9) LogicalDeviceDirectory LOGICAL NODE (CLAUSE 10) LogicalNodeDirectory GetAllDataValues DATA (CLAUSE 11) GetDataValues SetDataValues GetDataDirectory GetDataDefinition GE Multilin F60 Feeder Protection System C-23...
Page 638 LOGGING (CLAUSE 17) LOG CONTROL BLOCK GetLCBValues SetLCBValues QueryLogByTime QueryLogByEntry GetLogStatusValues GENERIC SUBSTATION EVENT MODEL (GSE) (CLAUSE 18, ANNEX C) GOOSE-CONTROL-BLOCK (CLAUSE 18) SendGOOSEMessage GetReference GetGOOSEElementNumber GetGoCBValues SetGoCBValues GSSE-CONTROL-BLOCK (ANNEX C) SendGSSEMessage GetReference GetGSSEElementNumber GetGsCBValues C-24 F60 Feeder Protection System GE Multilin...
Page 639 (QueryLogByTime or QueryLogAfter) c8: shall declare support for at least one (SendGOOSEMessage or SendGSSEMessage) NOTE c9: shall declare support if TP association is available c10: shall declare support for at least one (SendMSVMessage or SendUSVMessage) GE Multilin F60 Feeder Protection System C-25...
Page 640: C.7.1 Logical Nodes Table
GGIO: Generic process I/O GLOG: Generic log GSAL: Generic security application I: LOGICAL NODES FOR INTERFACING AND ARCHIVING IARC: Archiving IHMI: Human machine interface ISAF: Safety alarm function ITCI: Telecontrol interface ITMI: Telemonitoring interface C-26 F60 Feeder Protection System GE Multilin...
Page 641 PRTR: Rotor protection PSCH: Protection scheme PSDE: Sensitive directional earth fault PTEF: Transient earth fault PTOC: Time overcurrent PTOF: Overfrequency PTOV: Overvoltage PTRC: Protection trip conditioning PTTR: Thermal overload PTUC: Undercurrent PTUF: Underfrequency PTUV: Undervoltage GE Multilin F60 Feeder Protection System C-27...
Page 642 T: LOGICAL NODES FOR INSTRUMENT TRANSFORMERS TANG: Angle TAXD: Axial displacement TCTR: Current transformer TDST: Distance TFLW: Liquid flow TFRQ: Frequency TGSN: Generic sensor THUM: Humidity TLVL: Media level TMGF: Magnetic field TMVM: Movement sensor C-28 F60 Feeder Protection System GE Multilin...
Page 643 ZLIN: Power overhead line ZMOT: Motor ZREA: Reactor ZRES: Resistor ZRRC: Rotating reactive component ZSAR: Surge arrestor ZSCR: Semi-conductor controlled rectifier ZSMC: Synchronous machine ZTCF: Thyristor controlled frequency converter ZTRC: Thyristor controlled reactive component GE Multilin F60 Feeder Protection System C-29...
Page 644 C.7 LOGICAL NODES APPENDIX C C-30 F60 Feeder Protection System GE Multilin...
Page 645: D.1.1 Interoperability Document
Balanced Transmission Not Present (Balanced Transmission Only)   Unbalanced Transmission One Octet  Two Octets  Structured  Unstructured Frame Length (maximum length, number of octets): Not selectable in companion IEC 60870-5-104 standard GE Multilin F60 Feeder Protection System...
Page 646  <18> := Packed start events of protection equipment with time tag M_EP_TB_1  <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1  <20> := Packed single-point information with status change detection M_SP_NA_1 F60 Feeder Protection System GE Multilin...
Page 647  <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1  <104> := Test command C_TS_NA_1  <105> := Reset process command C_RP_NA_1  <106> := Delay acquisition command C_CD_NA_1  <107> := Test command with time tag CP56Time2a C_TS_TA_1 GE Multilin F60 Feeder Protection System...
Page 648 •Blank boxes indicate functions or ASDU not used. •‘X’ if only used in the standard direction TYPE IDENTIFICATION CAUSE OF TRANSMISSION MNEMONIC <1> M_SP_NA_1 <2> M_SP_TA_1 <3> M_DP_NA_1 <4> M_DP_TA_1 <5> M_ST_NA_1 <6> M_ST_TA_1 <7> M_BO_NA_1 <8> M_BO_TA_1 <9> M_ME_NA_1 F60 Feeder Protection System GE Multilin...
Page 649 <34> M_ME_TD_1 <35> M_ME_TE_1 <36> M_ME_TF_1 <37> M_IT_TB_1 <38> M_EP_TD_1 <39> M_EP_TE_1 <40> M_EP_TF_1 <45> C_SC_NA_1 <46> C_DC_NA_1 <47> C_RC_NA_1 <48> C_SE_NA_1 <49> C_SE_NB_1 <50> C_SE_NC_1 <51> C_BO_NA_1 <58> C_SC_TA_1 <59> C_DC_TA_1 <60> C_RC_TA_1 GE Multilin F60 Feeder Protection System...
Page 650 <120> F_FR_NA_1 <121> F_SR_NA_1 <122> F_SC_NA_1 <123> F_LS_NA_1 <124> F_AF_NA_1 <125> F_SG_NA_1 <126> F_DR_TA_1*) BASIC APPLICATION FUNCTIONS Station Initialization:  Remote initialization Cyclic Data Transmission:  Cyclic data transmission Read Procedure:  Read procedure F60 Feeder Protection System GE Multilin...
Page 651  Mode B: Local freeze with counter interrogation  Mode C: Freeze and transmit by counter-interrogation commands  Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously  Counter read  Counter freeze without reset GE Multilin F60 Feeder Protection System...
Page 652 Maximum number of outstanding I-format APDUs k and latest acknowledge APDUs (w): PARAMETER DEFAULT REMARKS SELECTED VALUE VALUE 12 APDUs Maximum difference receive sequence number to send state variable 12 APDUs 8 APDUs 8 APDUs Latest acknowledge after receiving I-format APDUs F60 Feeder Protection System GE Multilin...
Page 653: D.1.2 Iec 60870-5-104 Point List
D.1.2 IEC 60870-5-104 POINT LIST The IEC 60870-5-104 data points are configured through the    SETTINGS PRODUCT SETUP COMMUNICATIONS DNP / menu. Refer to the Communications section of Chapter 5 for additional details. IEC104 POINT LISTS GE Multilin F60 Feeder Protection System...
Page 654 D.1 IEC 60870-5-104 APPENDIX D D-10 F60 Feeder Protection System GE Multilin...
Page 655: E.1.1 Dnp V3.00 Device Profile
2048 Maximum Data Link Re-tries: Maximum Application Layer Re-tries:  None  None  Fixed at 3  Configurable  Configurable Requires Data Link Layer Confirmation:  Never  Always  Sometimes  Configurable GE Multilin F60 Feeder Protection System...
Page 656 FlexLogic. The On/Off times and Count value are ignored. “Pulse Off” and “Latch Off” operations put the appropriate Virtual Input into the “Off” state. “Trip” and “Close” operations both put the appropriate Virtual Input into the “On” state. F60 Feeder Protection System GE Multilin...
Page 657  16 Bits (Counter 8) Default Variation: 1  32 Bits (Counters 0 to 7, 9)  Point-by-point list attached  Other Value: _____  Point-by-point list attached Sends Multi-Fragment Responses:  Yes  No GE Multilin F60 Feeder Protection System...
Page 658: E.1.2 Implementation Table
Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F60 is not restarted, but the DNP process is restarted. F60 Feeder Protection System GE Multilin...
Page 659 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F60 is not restarted, but the DNP process is restarted. GE Multilin F60 Feeder Protection System...
Page 660 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F60 is not restarted, but the DNP process is restarted. F60 Feeder Protection System GE Multilin...
Page 661 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F60 is not restarted, but the DNP process is restarted. GE Multilin F60 Feeder Protection System...
Page 662: E.2.1 Binary Input Points
Change Event Variation reported when variation 0 requested: 2 (Binary Input Change with Time), Configurable Change Event Scan Rate: 8 times per power system cycle Change Event Buffer Size: 500 Default Class for All Points: 1 F60 Feeder Protection System GE Multilin...
Page 663: E.2.2 Binary And Control Relay Output
Virtual Input 27 Virtual Input 59 Virtual Input 28 Virtual Input 60 Virtual Input 29 Virtual Input 61 Virtual Input 30 Virtual Input 62 Virtual Input 31 Virtual Input 63 Virtual Input 32 Virtual Input 64 GE Multilin F60 Feeder Protection System...
Page 664: E.2.3 Counters
Events Since Last Clear A counter freeze command has no meaning for counters 8 and 9. F60 Digital Counter values are represented as 32-bit inte- gers. The DNP 3.0 protocol defines counters to be unsigned integers. Care should be taken when interpreting negative counter values.
Page 665: E.2.4 Analog Inputs
Change Event Variation reported when variation 0 requested: 1 (Analog Change Event without Time) Change Event Scan Rate: defaults to 500 ms Change Event Buffer Size: 256 Default Class for all Points: 2 GE Multilin F60 Feeder Protection System E-11...
Page 666 E.2 DNP POINT LISTS APPENDIX E E-12 F60 Feeder Protection System GE Multilin...
Page 667: F.1.1 Radius Server Configuration
Set up the RADIUS client on the UR as follows. Access Device > Settings > Product Setup > Security. Configure the IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the CLIENTS.CONF file.
Page 668 F.1 RADIUS SERVER CONFIGURATION APPENDIX F F60 Feeder Protection System GE Multilin...
Page 669: G.1.1 Revision History
31 August 2007 URX-246 1601-0093-R3 5.4x 17 October 2007 URX-251 1601-0093-S1 5.5x 7 December 2007 URX-253 1601-0093-S2 5.5x 22 February 2008 URX-258 1601-0093-S3 5.5x 12 March 2008 URX-260 1601-0093-T1 5.6x 27 June 2008 08-0390 GE Multilin F60 Feeder Protection System...
Page 670: G.1.2 Changes To The F60 Manual
12-3601 1601-0109-Z1 7.1x 30 March 2013 13-0126 1601-0109-Z2 7.1x 22 September 2013 13-0469 G.1.2 CHANGES TO THE F60 MANUAL Table G–1: MAJOR UPDATES FOR F60 MANUAL REVISION Z2 PAGE PAGE CHANGE DESCRIPTION (Z1) (Z2) Update General revision throughout document 5-115...
Page 671 Updated Table 2-8 Order Codes for vertical unit replacement modules to indicate that modules 8L and 8N cannot be ordered with module 8Z Update Updated Figure 3-10 Rear Terminal View Table G–5: MAJOR UPDATES FOR F60 MANUAL REVISION Y1 (Sheet 1 of 2) PAGE PAGE CHANGE...
Page 672 G.1 CHANGE NOTES APPENDIX G Table G–5: MAJOR UPDATES FOR F60 MANUAL REVISION Y1 (Sheet 2 of 2) PAGE PAGE CHANGE DESCRIPTION (X2) (Y1) 5-99 Added Figure: Data Set Created From User Selected Internal Items 5-100 Added Figure: Example Of Aggregator Data Sets...
Page 673: G.2.1 Standard Abbreviations
MTA ....Maximum Torque Angle FAIL....Failure MTR ....Motor FD ....Fault Detector MVA ....MegaVolt-Ampere (total 3-phase) FDH....Fault Detector high-set MVA_A....MegaVolt-Ampere (phase A) FDL ....Fault Detector low-set MVA_B....MegaVolt-Ampere (phase B) FLA....Full Load Current GE Multilin F60 Feeder Protection System...
Page 674 WRT....With Respect To RSTR ..... Restrained RTD ....Resistance Temperature Detector X ....Reactance RTU ....Remote Terminal Unit XDUCER..Transducer RX (Rx) ..Receive, Receiver XFMR..... Transformer s ..... second Z..... Impedance, Zone S..... Sensitive F60 Feeder Protection System GE Multilin...
Page 675: G.3.1 Ge Multilin Warranty
24 months from date of shipment from factory. In the event of a failure covered by warranty, GE Multilin will undertake to repair or replace the relay providing the warrantor determined that it is defective and it is returned with all transportation charges prepaid to an authorized service centre or the factory.
Page 676 G.3 WARRANTY APPENDIX G F60 Feeder Protection System GE Multilin...
Page 678 CRITICAL FAILURE RELAY ........2-24, 3-10 Modbus registers ............B-48 CSA APPROVAL .............. 2-28 settings ................ 5-234 CT BANKS DIGITAL OUTPUTS settings ................. 5-94 see entry for CONTACT OUTPUTS CT INPUTS ............3-12, 5-6, 5-94 DIMENSIONS ............. 3-1, 3-2 F60 Feeder Protection System GE Multilin...
Page 679 ELEMENTS ............... 5-4 FIRMWARE REVISION ............. 6-30 ENERGY ALOGRITHM FOR HI-Z ........8-1 FIRMWARE UPGRADES ............ 4-2 ENERGY METERING FLASH MESSAGES ............5-23 actual values ..............6-19 Modbus registers ............B-14 specifications ..............2-21 GE Multilin F60 Feeder Protection System...
Page 680 FLEX STATE PARAMETERS actual values ............6-8, 6-23 Modbus registers ..........B-19, B-48 settings ................. 5-80 G.703 ............ 3-30, 3-31, 3-32, 3-35 specifications..............2-19 GE TYPE IAC CURVES ..........5-163 FLEXCURVES GROUND CURRENT METERING ........6-17 equation ..............5-164 GROUND IOC Modbus registers ............B-54 FlexLogic operands ............
Page 681 LANGUAGE ..............5-23 MODIFICATION FILE NUMBER ........6-30 LASER MODULE ............. 3-29 MODULE FAILURE ERROR ..........7-7 LATCHING OUTPUTS application example ........... 5-268, 5-269 error messages ............... 7-9 settings ............... 5-267 specifications ..............2-23 GE Multilin F60 Feeder Protection System...
Page 682 OVERVOLTAGE FlexLogic operands ............5-140 auxiliary .............. 2-18, 5-206 logic ................5-203 negative sequence ............5-204 Modbus registers ............B-46 negative-sequence ............2-18 settings ............... 5-203 neutral ..............2-18, 5-203 specifications..............2-18 phase ..............2-17, 5-202 F60 Feeder Protection System GE Multilin...
Page 685 TROUBLE INDICATOR ..........1-19, 7-6 VOLTAGE ELEMENTS ........... 5-199 VOLTAGE HARMONICS ........... 6-21 VOLTAGE METERING Modbus registers ............B-13 specifications ..............2-21 values ................6-17 UL APPROVAL ..............2-28 VOLTAGE RESTRAINT CHARACTERISTIC ..... 5-165 GE Multilin F60 Feeder Protection System...
Page 686 Modbus registers ..........B-58, B-59 VTFF settings ................ 5-178 FlexLogic operands ............5-142 specifications ..............2-17 see VT FUSE FAILURE WEB SERVER PROTOCOL ..........5-53 WEBSITE ................1-2 WARNINGS ............... 1-1 WARRANTY ..............G-7 ZERO SEQUENCE CORE BALANCE .........3-12 F60 Feeder Protection System GE Multilin...

GE F60 Instruction Manual

1 Getting Started

2 Product Description

3 Hardware

4 Human Interfaces

5 Settings

Quick Links

Related Manuals for GE F60

Summary of Contents for GE F60