Table of Contents
Related Manuals for Miele DA 262 i
Summary of Contents for Miele DA 262 i
-
Page 1: Operating Instructions
Operating instructions Cooker hoods DA 262 i DA 272 i DA 292 i ]ö In order to protect yourself and avoid damage to your machine, it is absolutely necessary to read the operating instructions prior to installation and operation. M.-Nr. 04 076 101... -
Page 2: Description Of The Appliance
Description of the appliance Description of the appliance DA 262 i DA 272 i / DA 292 i... - Page 3 The control panel can either - be fitted with an aluminium front - Slide switch for the fan m facia panel, available from Miele, This is used to switch the fan on and off. - be fitted with a lightshield from the...
-
Page 4: Table Of Contents
Contents Contents Description of the appliance ......... 2 Help to protect our environment. -
Page 5: Help To Protect Our Environment
Help to protect our environment Help to protect our environment Disposal of packaging Disposal of your old machine The transport and protective packing is Old machines contain materials which mostly manufactured from the following can be recycled. Please contact your re-usable materials: local authorities or scrap merchant about potential recycling schemes, be-... -
Page 6: Warning And Safety Instructions
Warning and Safety instructions Warning and Safety instructions Read these Operating Instructions carefully before installing or using the Exhaust Hood. Repairs on electrical appliances This appliance is intended for should only be performed by quali- residential use only. Use the ap- fied personnel. - Page 7 Warning and Safety instructions Never connect an exhaust hood to When connecting the hood to an ex- an active chimney, dryer vent, vent ternal vent, make sure that there is flue, or room ventilating ductwork. Seek adequate ventilation in the room professional advice before connecting where the exhaust hood is to be an exhaust hood vent to an existing, in-...
- Page 8 Warning and Safety instructions Warning and safety instructions Disposal of discarded appliances Before discarding an old appliance, dis- connect its power cord to prevent it from becoming a hazard. SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY Throughout the manual, important safety items will be highlighted in boxes and should be read in con- junction with these “Warning and...
-
Page 9: Operation
Operation Operation After cooking If, after finishing cooking, there are still cooking vapors in the kitchen, it is rec- ommended that the cooker hood be left on for some minutes longer. Then switch the cooker hood off by: moving the slide switch for the fan and the cooktop illumination switch to the ”0“... -
Page 10: Cleaning And Care
Cleaning and care Cleaning and care Before any cleaning or maintenance work, the extractor must be discon- nected from the mains supply (switch off at the wall socket and remove plug or the fuse). Cleaning To remove the grease filters push the The cooker hood housing may be filter holder retainers towards the cleaned using hot water to which a little... - Page 11 Cleaning and care Cleaning and care When removing the filters for clean- Release the light tube and the starter ing, also clean off any residues of oil by turning them and then lifting them or fat from the filter housing to pre- out of their holders.
-
Page 12: After Sales Service
In the event of any fault which you can- not correct yourself please contact Your Miele Dealer The Miele Service Department The address of the nearest Service De- partment is given on the back page. When contacting the Service Depart- ment, please quote the Model and Ser- ial No. -
Page 13: Electrical Connection
Electrical connection Electrical connection For CDN only: For USA only: The cooker hoods are supplied with a The cooker hoods are supplied with a 1.50 m power supply cable ready for 5 ft power supply cable ready for con- connection to an a.c. single phase nection to an a.c., single phase, 120 V / 60 Hz supply. -
Page 14: Technical Data
Technical data Technical data DA 262 i DA 272 i DA 292 i 225 W 223 W 235 W Total rated load 15 W 13 W 16 W Light 120 V 120 V 120 V Voltage 60 Hz 60 Hz... -
Page 15: Installation
– DA 262 i = 600 mm (23 5/8") The distance between the top of the cooktop and the bottom of the – DA 272 i = 700 mm (21 9/16") cooker hood should be at least: –... -
Page 16: Appliance Dimensions
Appliance dimensions Wall unit dimensions A: DA 262 i = 560; DA 272 i = 660; DA 292 i =860 B: DA 262 i = 595; DA 272 i = 695; DA 292 i =895 A: DA 262 i = 562-568 = 22 1/8" - 22 3/8"... -
Page 17: Building In
Installation Installation Building in Take the dividing wall out of the wall unit. Push the brackets into the slots on the sides of the cooker hood. 19 mm ( 3/4 ") thick side walls: Secure the support tracks to both interior walls of the unit using two 3,5 x 16 mm ( 5/8 ") screws, position as illustrated. -
Page 18: Depth Alignment
Pull the deflector plate out to its limit and remove the grease filters. 4 holes (DA 262 i / DA 272 i) or 6 holes (DA 292 i) are now visible. Use a sharp pointed instrument through these holes to gouge out the fixing holes. -
Page 19: Fitting The Light Tube Cover
Attach the spacer bar to the guide rail (2) located behind the light tube. Fitting the light tube cover – DA 262 i Pull off the transit strips on each side. Fitting the cover caps For cooker hoods without a front panel... - Page 20 Installation Installation Only use the template for lightshields with the following lengths: DA 262 i DA 272 i Da 292 i 598 mm 698 mm 898 mm 597 mm 697 mm 897 mm 596 mm 696 mm 896 mm 595 mm...
-
Page 21: Fitting The Front Facia Panel / Lightshield
Remove the screws now visible For lightshields with a Miele kitchen (DA 262 i / DA 272 i = 4; furniture programme use DA 292 i = 6) using a Philips screw- 3.5 x 16 mm ( 5/8 " ) screws supplied. -
Page 22: Air Extraction
1 cm per hood. metre (1/8" per foot) , to ensure no condensation drains into the ap- pliance. – If the exhaust air is to be ducted out- side, the installation of a Miele tele- scopic wall vent is recommended. - Page 23 Air extraction Air extraction Measure the total length of the ex- haust ducting to be used. Add the appropriate length of addi- tional piping to this figure (see table), according to the number and type of bends: Type Angle Radius of Length of bend additional...
-
Page 24: Air Recirculation
The following parts are necessary for this, available from your Miele Dealer or from the Miele Spare Parts Department: Conversion kit from extraction to re- circulation (Ø... - Page 28 Alteration rights reserved / 44 / 001 CDN, USA - 1998 This paper is made from 100% chlorine-free bleached cellulose and therefore protects the environment.