Dell 1907FPc Service Manual 19” LCD MONITOR DELL 1907FPc THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY.EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OFTHIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR...
Dell 1907FPc Revision List Revision Release Date Revise history TPV model Remark T980KSCDKRDFUP T980KSCDKRDMUP Nov.-28-2005 Initial Release T980KGCHKRDGUP T980KGCHKRDEUP ROHS BOM Sold area in EU and attach the T980KSCHBRDGQP Dec.22-2005 corresponding BOM Mar.-28-2006 Add “Definition Of Pixel Defects” Add” Max Brightness measurement ” on...
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINGS Proper service and repair is important to the safe, reliable operation of all Dell Company** Equipment. The service procedures recommended by Dell and described in this service manual are effective methods of performing service operations.
165MHz (Max) Optimal preset resolution 1280 x 1024 at 60 Hz Highest preset resolution 1280 x 1024 at 75 Hz Plug & Play VESA DDC ON Mode (with Dell Sound bar and USB <65W EPA ENERGY ® active) STAR OFF Mode <3W...
Dell 1907FPc 2. LCD Monitor Description The LCD monitor will contain a main board, Power board, key board, and USB board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
Dell 1907FPc 3. Operation instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
Page 8
Use the Input Select button to select between two different video signals that may be connected to your monitor. NOTE: The floating 'Dell Self-test Feature Check' dialog appears on a black background If the monitor cannot sense a video signal. Depending upon the selected input, one of the dialogs shown below will scroll continually.
Page 9
Use to mount the monitor. (Behind attached base plate) Barcode serial number label Refer to this label if you need to contact Dell for technical support. Security lock slot Use a security lock with the slot to help secure your monitor.
Page 10
Dell 1907FPc Power connector Insert the power cable. Dell Soundbar power connector Connect the power cord for the Soundbar (optional). DVI connector Connect your computer DVI cable. VGA connector Connect your computer VGA cable. Connect the USB cable that came with your monitor to the monitor USB upstream connector and the computer.
Dell 1907FPc 3.3 Adjusting the Picture NOTE: If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor automatically saves those changes. The changes are also saved if you change the settings and then wait for the OSD menu to disappear.
Page 12
Dell 1907FPc Menu and Icon Description Submenus Select to exit the Main menu Exit Brightness adjusts the luminance of the backlight. Brightness/ Contrast Adjust Brightness first, then adjust Contrast only if further adjustment is necessary. Push the + button to increase luminance and push the - button to decrease luminance (min 0 ~ max 100).
Page 13
Dell 1907FPc NOTE: When using DVI source, the Positioning option is not available. Auto Adjust Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with your particular setup. Select to activate automatic setup and adjustment. The following dialog appears...
Page 14
Dell 1907FPc Blue Preset The color hue is most noticeable in areas of white. • Red Preset Blue Preset is selected to obtain a bluish tint. This color setting is typically used for text based applications (spreadsheets, programming, Normal text editors, etc.).
Page 15
Dell 1907FPc NOTE: When the OSD is locked, pressing the menu button takes the user directly to the OSD settings menu, with OSD Lock selected. Select No (-) to unlock and allow user access to all applicable settings. OSD Lock NOTE: You can also lock or unlock the OSD by pushing and holding the Menu button for 15 seconds.
Page 16
Dell 1907FPc NOTE: When the Dell Soundbar is not properly connected to the monitor, the audio menu is not available. Reset the OSD menu options to the factory-preset values. Factory Reset: Exit — Select to exit out of Reset to Factory Settings menu without resetting any OSD options.
Dell 1907FPc NOTE: The floating Dell Self-test Feature Check dialog appears on-screen if the monitor cannot sense a video signal. Occasionally, no warning message appears, but the screen is blank. This could also indicate that the monitor is not synchronizing with the computer.
Page 18
Dell 1907FPc 1. Turn off your computer and disconnect the power cable. 2. Connect either the white DVI or blue VGA cables to the connectors on the computer and the monitor. Connect the USB cable that was included with your monitor to the computer and the upstream USB connector on the monitor.
Dell 1907FPc 4. Input/Output Specification 4.1 Input Signal Connector 4.1.1 D-Sub Connector Signal Assignment Pin. Signal Assignment Red Video DDC +5V Green Video GND-Sync Blue Video DDC Data Self Test H-Sync R-Ground V-Sync G-Ground DDC Clock B-Ground VGA Connector layout 4.1.2 DVI Connector...
Page 27
Dell 1907FPc 1) MCU Initializes. 2) Is the EEprom blank? 3) Program the EEprom by default values. 4) Get the PWM value of brightness from EEprom. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
Dell 1907FPc 8. Disassembly Flow Chart Tools: 2 Power screwdrivers (φ=5mm,L=60mm); 1 small cross screwdriver; turnbuckle driver; Setting: Power screwdriver torque A=11 kgF. Cm; torque B=6 kgF. Cm Note: Firstly, put the monitor on a soft, flat and clean surface, wear gloves.
Page 44
Dell 1907FPc 3. Take off the bezel Remove rear cover : Turn over the monitor as the Fig, hold the rear cover, and then slightly remove it. Remove the shield : 1. Remove the 4 screws by Torque B...
Page 45
Dell 1907FPc 2. Remove the USB2 board cover by Torque B or by manual 3. Remove the 5 screws by Torque B or by manual 4. Disconnect the wire harness between USB1 and USB2...
Page 46
Dell 1907FPc 5. Push the main shield as the arrowhead direction Disconnect the connector pin: Disconnect the connector pin between key and main boards Install: Lay the KEPC cable as the figure showed...
Page 47
Dell 1907FPc Remove USB and main board : 1. Remove the 7 screws by Torque B 2. Disconnect the connector wire...
Page 48
Dell 1907FPc 3. Disconnect the wire harness between main board and panel EVA washers Magnetism ring Cable hook Install: Fix the LVDS cable by black tape and cable hook Black tape...
Page 49
Dell 1907FPc 4. Disconnect the wire holder Install: Lay the cables as the line direction Remove the power board : Remove the 5 screws by Torque...
Page 50
Dell 1907FPc Disconnect wire harness : Disconnect the wire harness between power board and lamps Fix the CCFL connector by black tapes as the figure Remove USB board : Remove the 2 screws by Torque...
Page 51
Dell 1907FPc Remove the main frame : Remove the 4 screws (left and right) by manual or torque = 3kgF.Cm Cable hook Cable hook Samsung panel: The CCFL line can’t overtop dashed LG panel: The angle between CCFL line and vertical direction should be...
Dell 1907FPc 9. Maintainability 9.1 Equipments and Tools Requirement 1. Voltage meter 2. Oscilloscope 3. Pattern Generator 4. LCD Color Analyzer 5. Service Manual 6. User Manual...
Dell 1907FPc 9.2 Trouble shooting 9.2.1 Main Board Note: 1. If replace “Main-Board”, Please re-do “DDC-content” programmed & “White-Balance”. 2. If replace “Power Board” only, Please re-do “ White-Balance”. No power No power Press power key and look if the...
Page 54
Dell 1907FPc No picture (LED is orange) No picture Measure U601 PIN2=3.3V U602 PIN2=1.8V Replace U601, U602 X301 oscillate waveforms are normal Replace X301 Check if the sync signal from computer is output and video cable is connected normally Input the sync signal of...
Page 55
Dell 1907FPc White screen White screen Measure Q603 base X301 oscillate waveform is normal is high level? Replace X301 Check Q602, Q603 is broken Check reset circuit of or CN501 solder? U401 is normal Check Correspondent Check Correspondent component. component.
Page 56
Dell 1907FPc 9.2.2 Inverter/Power Board No Power No power Check AC line volt 110V or 220V Check AC line Check the voltage of C903(+) Check F901, bridge rectified circuit Check start voltage for the pin3 of IC901 Check R903, R04, R905...
Page 58
Dell 1907FPc 9.2.3 Key Board OSD is unstable or not working Is Keypad board connecting normally? Connect Keypad Board Is Button Switch normally? Replace Button Switch Is Keypad board normally? Replace Keypad Board Check main board...
Dell 1907FPc 10. White balance, Luminance adjustment Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment. Before started adjust white balance, please setting the Chroma-7120 MEM. Channel 3 to 6500 K colors, MEM. Channel 4 to 9300 K colors, MEM.
Page 60
Dell 1907FPc 18. Adjust the RED on OSD window until chroma 7120 indicator reached the value R=100 19. Adjust the GREEN on OSD, until chroma 7120 indicator reached G=100 20. Adjust the BLUE on OSD, until chroma 7120 indicator reached B=100 21.
Dell 1907FPc 12. ISP Instruction 12.1 Software requirement and connection Operating system requirement (1) Microsoft windows OS. (2) 100M free hard-drive space. (3) 1 free parallel port for DDC2BI communication. The hardware Connection 12V Input Link to Dell DVI connector...
Dell 1907FPc 12.2 Install the software (Gprobe 5.0) for ISP Writer A. Double-click the Install software Select the folder where you would like Genesis Gprobe 5 to be installed Completing the Genesis Gprobe 5 setup wizard Note: After finishing the installation, you must restart the PC.
Page 64
Dell 1907FPc B. Next, install the Update software Completing the update 1 for Genesis Gprobe 5.0 setup wizard C. Copy the to C: program files → GProbe5.0.0.15 → Genesis Microchip → GProbe 5 → ChipDB folder, Installation Finished.
Page 65
Dell 1907FPc 12.3 Run program After the installation, a short-cut icon will appear on your desktop, double click it will run the program. (1). Select the IC type (NOTE: If there is not this selection, please check the “ChipDB”): Note: Firstly, you can check the I²C normal or not by inputting the “test” in the position where to load MCU software.
Page 66
Dell 1907FPc Set the Connection Settings → Connection → Device to Parallel, click OK! (3). Select Commands → Batch:...
Page 67
19TLB4 (.txt) Click open. (4). Unplug the Dell AC power, until the LED indicator is off, press Enter or Execute button, when the .txt of MCU is in gray, for example , re-plug Dell AC power, Writer is in progress.
Dell 1907FPc 13. Check List 1) After replacing LCD Main board and panel, Check if white-balance is within the specs, then re-writing DDC is necessary. The white-balance value for each common color temperature: 9300 parameter is x=283±28, y=297±28, Y = 180 ±10 cd/m 6500 parameter is x =313±28, y=329±28, Y = 180 ±10 cd/m...
Page 69
Dell 1907FPc 7. Select Exit to the upper menu after completing the adjustment. Then press POWER OFF to exit and save it. 3) Steps for writing DDC: 1. Employ PC, and connect the DDC-writing instrument and the instrument that is ready for writing into DDC to the power of 12V.
Page 70
Dell 1907FPc Notes: 1. Make sure the system time of PC is in accordance with the real time before writing. 2. The schematic picture is just as an example for description; the exact content of the DDC is dependent on the serial number of the BARCORD of this model.
Dell 1907FPc 14. BOM List Different key Parts List Part NO Description Quantity Unit Remark 750GLG90E3T21Z D 19" TLB2 ZBD PANEL T980KGCHKRDEUP 750GLG90E3T41Z D LPL 19" TLB4 ZBD PANEL T980KGCHKRDGUP 750GLS90EX1 Z SEC 19" EX-L01-L00 PANEL T980KSCDKRDFUP 750GLS90X2111Z SEC 19" EX-L21-CL6 PANEL...
Page 72
Dell 1907FPc 40G 19N700 4A RATING LABEL 40G 581700 3A6813 CARTON LABEL 41G780070039A 41G780070043A 44G3231 12 A EVA WASHER 44G3947 1 EPS(L) 44G3947 2 EPS(R) 44G3947 3 EPS(M) 44G3947700 2A CARTON 45G 88609 26 EPE BAG FOR BASE 45G 88609 27...
Page 103
Dell 1907FPc CN705 88G 352 2 CL USB COW CN706 88G 352 2 CL USB COW CN707 95G8014 10 30 WAFER 10P RIGHT ANGLE P 19G 588 3 SPRING HOLDER 85G 724 1 B SHIELD COVER 12G6201 1 L TYPE RUBBER...
Page 104
Dell 1907FPc 15. Definition Of Pixel Defects Type 1. 750GLG90E3T21Z D LM190E03-TLB2 Dot Defect Bright Dot Dark Dot...
Page 105
Dell 1907FPc Total amount of Dot Defects -------------------------5 Max(Combination) Polarizer Defects Foreign Material Line Defect Bezel Appearance Others...
Page 106
Dell 1907FPc Type 2. 750GLG90E3T41Z D LM190E03-TLB4 Dot Defect Bright Dot Dark Dot Total amount of Dot Defects -------------------------5 Max(Combination) Polarizer Defects...
Page 107
Dell 1907FPc Foreign Material Line Defect Bezel Appearance Others Type 3. 750GLS90EX1 Z LTM190EX-L01...