IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death. Do not store or use gasoline or other Installation and service must be ...
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. www.GEAppliances.ca PROPER INSTALLATION This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting www.GEAppliances.ca, or call 1-800-561-3344.
Page 4
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! YOUR LAUNDRY AREA Keep the area underneath and around your Keep all laundry aids (such as detergents, bleaches, appliances free of combustible materials (lint, etc.) out of the reach of children, preferably in a paper, rags, etc.), gasoline, chemicals and other locked cabinet.
www.GEAppliances.ca WHEN USING YOUR DRYER (cont.) Never attempt to operate this appliance if it is You may wish to soften your laundered fabrics damaged, malfunctioning, partially disassembled, or reduce the static electricity in them by using or has missing or broken parts, including a a dryer-applied fabric softener or an anti-static damaged cord or plug.
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Throughout this manual, features and appearance may vary from your model. You can locate your model number at the top inside of the door opening. Models GFDN110/120/130, GFMN110/120/130, and GMMN120 Models GFDS140/145/150/155 and GFMS140/145/150/155...
About the dryer control panel. www.GEAppliances.ca Power Press to “wake up” the display. If the display is active, press to put the dryer in the standby mode. NOTE: Pressing Power does not disconnect the appliance from the power supply. Dry Cycles The dry cycle controls the length and tumble speed of the drying process.
Page 8
Sensor Dry “Level” The sensor continuously monitors the amount of moisture in the load. When the moisture in your clothes reaches your selected dry level, the dryer will stop. Note: Sensor dry “Level” only works for Normal Mixed Load, Cottons, Bulky Bedding, Easy Care, Delicates and Speed Dry.
About cycle options. NOTE: Not all features are available on all dryer models. www.GEAppliances.ca Extended Tumble The extended tumble time does not get Minimizes wrinkles by adding approximately added to the cycle time on the display 60 minutes of no-heat tumbling after clothes are dry.
About cycle options. NOTE: Not all features are available on all dryer models. Lock You can lock the controls to prevent any To lock the dryer, press and hold the lock icon selections from being made. You can also lock for 3 seconds.
Reversing the door swing. www.GEAppliances.ca IMPORTANT: Once you begin, do not move IMPORTANT NOTES: the cabinet until door-swing reversal is Read the instructions all the way completed. through before starting. These instructions are for changing the Handle parts carefully to avoid hinges from the right side to the left scratching paint.
Page 12
Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Remove Door Assembly 2. Open the door to approximately 130 degrees. 3. Remove the 4 screws starting from the bottom to the top. Make sure the door is supported while removing the screws. Remove Top Screw 4.
Page 13
www.GEAppliances.ca STEP-BY-STEP INSTRUCTIONS (cont.) Reinstall Hinge Assembly 7. Install the hinge assembly in the opposite side of the door as shown. Push the hinge assembly in place until the hinge holes align with the door holes. Machine screws 8. Hold the hinge and door on their side with one hand and fasten the 4 machine screws as shown.
Page 14
Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Outer Door Reassemble Door Assembly IMPORTANT: Make sure there is no dirt or any other foreign material in between the window panes. 11. Place the plastic outer door onto the inner door. Make sure that the handle part of the outer door is opposite the hinge as shown.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce Fabric Conditioner Dryer Sheets ® have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions.
The stainless steel used to make the dryer drum provides the highest reliability available in a GE dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode.
Venting the dryer. www.GEAppliances.ca For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the Installation Instructions. ...
Connecting Inlet Hoses. To produce steam, the dryer must connect to the cold water supply. Since the washer must also connect to the cold water, a “Y” connector is inserted to allow both inlet hoses to make that connection at the same time. NOTE: Use the new inlet hoses provided;...
Stacking. www.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT: Save these instructions for local Note to Consumer – Keep these instructions for electrical inspector’s use. future reference. IMPORTANT: Observe all governing codes and Installation must be performed by a qualified ordinances.
Page 20
Stacking. KIT CONTENTS (optional kit GE FL STACK) Right Hand Bracket 4 #12 x 1” Screws 4 Rubber Pads Left Hand Bracket 4 #8 x 1/2” Screws TOOLS YOU WILL NEED Phillips Screwdriver Gloves Pliers Open-Ended Wrench Level INSTALLATION PREPARATION Remove the packaging.
www.GEAppliances.ca INSTALLING THE STACK BRACKET KIT 1. Remove the Dryer Leveling Legs A. Carefully lay the dryer on its side. Use the packing material so you don’t scratch the finish on the dryer. B. Use an open-end wrench or pliers to remove the dryer leveling legs.
Page 22
Stacking. INSTALLING THE STACK BRACKET KIT (cont.) 4. Prepare the Washer and Dryer A. Place the washer in the approximate C. Reverse dryer door swing if desired. location. See dryer Installation Instructions for details. B. Make sure the washer is level. Refer to washer Installation NOTE: The washer door swing is not Instructions for details.
Before you call for service… www.GEAppliances.ca Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit www.GEAppliances.ca. You may not need to call for service. PROBLEM Possible Causes What To Do Dryer shakes or Some shaking/noise is normal. •...
Page 24
Before you call for service… PROBLEM Possible Causes What To Do Time Remaining The estimated time may change • This is normal. jumped to a when a smaller load than usual lower number is drying Cannot make a The DRYNESS Level, TEMP •...
Page 25
• Try a fabric softener. • Bounce Fabric Conditioner Dryer Sheets have been ® approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. Overdrying • Try a fabric softener. • Adjust setting to Less Dry or Damp.
Page 26
Before you call for service… PROBLEM Possible Causes What To Do Small amount of water Inadequate load size for steam • If using the Steam DeWrinkle cycle, manually reduce cycle on floor in front of dryer cycle selected, excess steam time.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service.
Page 29
Any part of the dryer which fails due to a defect in materials or workmanship. During this From the date of the limited one-year warranty, GE will also provide, free of charge, all labor and related service costs original purchase to replace the defective part.
Contact Us www.GEAppliances.com In the U.S.: If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations GE Appliances, Appliance Park Louisville, KY 40225 In Canada: www.GEAppliances.ca, or write to: Director, Consumer Relations, Mabe Canada Inc.