Related Manuals for Miele DA 3060
Summary of Contents for Miele DA 3060
- Page 1 Operating and installation instructions Cooker hood DA 3060 To avoid the risk of accidents GiWOZ or damage to this appliance it is to read these instructions before it is installed and used for the first time. M.-Nr. 06 681 520...
- Page 2 ......... . 3 .
- Page 3 Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment. disposal, and can normally be They are, however, essential for the recycled.
- Page 4 This appliance complies with all Before connecting the appliance to relevant local and national safety the mains supply, make sure that requirements. Inappropriate use the voltage and frequency details given can, however, lead to personal injury on the data plate correspond with the and damage to property.
- Page 5 The appliance is only completely isolated from the electricity supply Never use an open flame beneath when: the cooker hood. To avoid the – it is switched off at the wall socket danger of fire, do not flambé or grill and the plug withdrawn, over an open flame under the cooker hood.
- Page 6 The filter should be regularly cleaned or changed as The appliance is only intended for appropriate. A saturated filter is a fire use by adults who have read these hazard. See "Cleaning and care". instructions. Keep children well away Do not use a steam-cleaner to from the appliance at all times and clean this appliance.
- Page 7 All ducting, pipework and fittings - 650 mm above gas hobs and cookers, must be of non-flammable material. - 650 mm above an open grill or deep These can be obtained from the Miele fat fryer. Spare Parts department or from builders’ merchants.
- Page 8 Harmful gases such as carbon monoxide could be drawn out of the chimney or extraction ducting back into the room, with potentially fatal consequences. In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the extractor and the heater are in operation simultaneously, an underpressure in the room of 0.04 mbar...
- Page 9 If the only way of ensuring adequate ventilation is via an open window, then Before discarding an old a window contact switch should be appliance, switch off and fitted. disconnect it from the power supply. The window contact switch ensures that Cut off and render any plug useless.
- Page 11 ø 150 mm ^ Pull out the deflector plate. ^ To switch on, slide the switch to the required setting. Depending on the intensity of the cooking vapours, levels "1" to "3" are usually sufficient for normal cooking. (extra accessory available to order For short periods of intensive cooking for recirculation mode) vapours, e.g.
- Page 12 Charcoal filters are available to order socket in the motor unit. through your Dealer or the Miele Spare Parts Department. (See back cover for Having a non-return flap fitted in the contact details and "Technical Data" for ducting ensures that air, once ducted to model number).
- Page 13 (in countries where this is applicable). A microfibre “E-Cloth” is available from (This infomation does not apply to the the Miele UK Spare Parts Department, controls). which is suitable for cleaning surfaces such as stainless steel, glass, plastic Stainless steel surfaces can be cleaned...
- Page 14 (optional accessory) Aluminium is affected by the way that light falls on it, by the surrounding environment and by the angle you observe it from. Aluminium surfaces may suffer discolouration or damage if soiling is ^ Grip the front of the deflector plate left on them for too long.
- Page 15 Miele Spare Parts department. prevent the risk of these catching fire. See back cover for contact details, and "Technical data" for type and reference number.
- Page 16 ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off. Do not touch the surface directly when changing a lamp, as grease particles from your fingers will...
- Page 17 The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows, unless a greater distance is specified by the manufacturer of your cooking appliance: - 450 mm above electric hobs and cookers, - 650 mm above gas hobs and cookers,...
- Page 19 for securing the vent ducting to the exhaust socket. for securing the cooker hood into the for exhaust ducting C125 mm. wall unit. for fitting into the exhaust socket on the motor unit (only for air extraction mode). for securing the cooker hood to the brackets.
- Page 21 = Depth of carcase minus depth of ^ Screw the spacer strip to the bottom appliance of the sides of the housing, flush with ^ The depth of appliance depends the rear wall. on the lightshield being used: – a Lightshield to match existing kitchen furniture –...
- Page 22 ^ Place the appliance on its back. Do not remove the protective film between the deflector plate and the casing until the hood has been placed in the housing unit. ^ Screw the brackets onto the right and left inside walls of the housing unit as shown.
- Page 23 Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the brackets, allowing the appliance to be removed from the unit. ^ Push the cooker hood back against the spacer strip. ^ Pull out the deflector plate. ^ Lift the appliance up into the housing from below, and engage in the brackets.
- Page 24 ^ Secure the front of the appliance to the floor of the housing unit from below using 4 screws. – Drill respective holes and screw the fixing brackets to the wall or the To avoid damaging the deflector plate cabinet rear wall. Tighten the screws when it is pulled out, care should be to the casing.
- Page 25 ^ Remove the protective strip around the edge of the grease filter. Replace the grease filter. ^ Attach the lightshield (if using). ^ To do this, pull the deflector plate out. A DML 300 installation kit, available as an optional accessory, is required for this.
- Page 26 For this, we recommend using the conversion kit available from your Miele dealer or the Miele Spare Parts Dept (see "Technical data"). You will also need a charcoal filter (see ^ If the on-site ventilation system does “Technical data”).
- Page 27 ^ Screw the exhaust grille to the top of the unit. When fitting the exhaust grille make sure that the slats in the grille point towards the centre of the room and not directly towards a wall or the ceiling. ^ Fit the charcoal filter (see “Cleaning and care”).
- Page 28 – Where ducting is horizontal, it must Important: To avoid the danger of be laid to slope away at at least 1 cm toxic fumes, please observe the per metre. Warning and Safety instructions. This is to ensure that condensate This is especially crucial when using cannot drain back into the cooker the cooker hood at the same time as...
- Page 29 If the exhaust ducting is to run through To achieve even further reductions in rooms, ceiling space etc. where there noise levels, a special silencer can be may be great variations in temperature fitted in the ducting system. between the different areas, the On extraction models, it can be fitted problem of condensation will need to nearest the ducting outlet to the outside...
- Page 30 be provided for all poles. All electrical work should be For extra safety it is advisable to install undertaken by a suitably qualified a residual current device (RCD) with a and competent person in strict trip current of 30 mA. accordance with current national and local safety regulations (BS 7671 in the UK).
- Page 31 In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer – The Miele Service Department (see back cover for address). When contacting your Dealer or the Service Department, please quote the model and serial number of your appliance.
- Page 32 Connected load....210 W Fan motor ....110 W Hob lighting ... . . 2 x 50 W Voltage UK, IRL, NZ .
- Page 36 Alteration rights reserved / 1006 M.-Nr. 06 681 520 / 02 en - GB...