hit counter script
Dell Inspiron 15 3537 Owner's Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Laptop
  5. Inspiron 15 3537
  6. Owner's manual

Dell Inspiron 15 3537 Owner's Manual

Inspiron 15 3537 owner's manual
Hide thumbs Also See for Inspiron 15 3537:
Table of Contents

Advertisement

Quick Links

Inspiron 15/15R
Owner's Manual
Computer model: Inspiron 3521/5521/5537/3537
Regulatory model: P28F
Regulatory type: P28F001/P28F003

Advertisement

Table of Contents
loading

Related Manuals for Dell Inspiron 15 3537

Summary of Contents for Dell Inspiron 15 3537

  • Page 1 Inspiron 15/15R Owner’s Manual Computer model: Inspiron 3521/5521/5537/3537 Regulatory model: P28F Regulatory type: P28F001/P28F003...
  • Page 2 , and the Windows start button logo are either trademarks or registered ® trademarks of Microsoft Corporation in the United States and/or other countries; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license. 2013 - 06 Rev. A02...

  • Page 3: Table Of Contents

    Contents Before You Begin ......Safety Instructions ......Recommended Tools .
  • Page 4 Removing the Keyboard ....Prerequisites ......Procedure .
  • Page 5 Removing the Coin-Cell Battery ....Prerequisites ......Procedure .
  • Page 6 Removing the Display Bezel ....Prerequisites ......Procedure .

  • Page 7: Before You Begin

    Before You Begin CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. Save and close all open files and exit all open programs. Remove any media card and optical disc from your computer. Follow the instructions to shut down your computer based on the operating system installed on your computer.

  • Page 8: Safety Instructions

    For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. WARNING: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the computer, replace all covers, panels, and screws before connecting to the power source.

  • Page 9: After Working Inside Your Computer

    After Working Inside Your Computer After you complete the replacement procedures, ensure the following: • Replace all screws and ensure that no stray screws remain inside your computer. • Connect any external devices, cables, cards, and any other part(s) you removed before working on your computer.

  • Page 10: Removing The Battery

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Close the display and turn the computer over.

  • Page 11: Replacing The Battery

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the tabs on the battery with the slots on the battery bay and snap the battery into place.

  • Page 12: Removing The Memory Module(S)

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 13 Use your fingertips to carefully spread apart the securing clips on each end of the memory-module connector until the memory module pops up. Slide and remove the memory module from the memory-module connector. securing clips (2) memory-module connector memory module Removing the Memory Module(s)

  • Page 14: Replacing The Memory Module(S)

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the notch on the memory module with the tab on the memory-module connector.

  • Page 15: Removing The Optical-Drive Assembly

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 16 Remove the screws that secure the optical-drive bracket to the optical-drive assembly. Remove the optical-drive bracket from the optical-drive assembly. Carefully pry the optical-drive bezel and remove it from the optical-drive assembly. optical-drive bezel optical drive screws (2) optical-drive bracket Removing the Optical-Drive Assembly...

  • Page 17: Replacing The Optical-Drive Assembly

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the tabs on the optical-drive bezel with the slots on the optical drive and snap the optical-drive bezel into place.

  • Page 18: Removing The Hard-Drive Assembly

    Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. CAUTION: To avoid data loss, do not remove the hard drive while the computer is in Sleep or On state.
  • Page 19 Using the pull-tab, lift the hard-drive assembly out of the computer base. hard-drive assembly pull-tab Remove the screws that secure the hard-drive bracket to the hard drive. Lift the hard-drive bracket off the hard drive. screws (2) hard-drive bracket Removing the Hard-Drive Assembly...

  • Page 20: Replacing The Hard-Drive Assembly

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive.

  • Page 21: Removing The Keyboard

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 22 Lift the connector latch and disconnect the keyboard cable from the system board. Lift the keyboard off the palm-rest assembly. connector latch keyboard cable keyboard Removing the Keyboard...

  • Page 23: Replacing The Keyboard

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Slide the keyboard cable into the connector on the system board and press down on the connector latch to secure it.

  • Page 24: Removing The Palm Rest

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 25 Turn the computer over and open the display as far as possible. Lift the connector latches and, using the pull-tabs, disconnect the touchpad cable and the power-button cable from the system board. touchpad cable power-button cable connector latches (2) Removing the Palm Rest...
  • Page 26 Remove the screws that secure the palm-rest to the system board. CAUTION: Carefully separate the palm rest assembly from the display assembly to avoid damage to the display assembly. Using a plastic scribe, gently lift and release the tabs on palm rest from the slots on the computer base.

  • Page 27: Replacing The Palm Rest

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the screw holes on the palm rest with the screw holes on the computer base.

  • Page 28: Removing The Wireless Mini-Card

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 29 Slide and remove the wireless mini-card out of the mini-card connector. wireless mini-card mini-card connector Removing the Wireless Mini-Card...

  • Page 30: Replacing The Wireless Mini-Card

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure CAUTION: To avoid damage to the wireless mini-card, ensure that no cables are placed under the wireless mini-card.

  • Page 31: Removing The I/O Board

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.

  • Page 32: Replacing The I/O Board

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Gently slide the I/O board below the tab that secures it and snap the I/O board into place.

  • Page 33: Removing The System Board

    Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in system setup after you replace the system board. For more information, see "Entering the Service Tag in system setup"...

  • Page 34: Procedure

    Procedure Peel off the tape that secures the display cable to the system board. Disconnect the display cable from the system board. Disconnect the power-adapter port cable, speaker cable, and the I/O-board cable from the system board. display cable tape power-adapter port cable speaker cable I/O-board cable...
  • Page 35 Remove the screw that secures the system board to the computer base. Lift the system board off the computer base. system board screw Removing the System Board...

  • Page 36: Replacing The System Board

    Entering the Service Tag in system setup Turn on the computer. Press <F2> when you see the Dell logo to enter system setup. Navigate to the Main tab and type your computer’s Service Tag in the Service Tag Input field.

  • Page 37: Removing The Coin-Cell Battery

    Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. WARNING: The coin-cell battery may explode if installed incorrectly. Replace the coin-cell battery only with the same or equivalent type. Discard used coin-cell batteries according to the manufacturer’s instructions.

  • Page 38: Procedure

    Procedure Turn the system board over and place it on a flat surface. Using a plastic scribe, gently pry out the coin-cell battery out of the battery socket on the system board. plastic scribe coin-cell battery Removing the Coin-Cell Battery...

  • Page 39: Procedure

    Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. WARNING: The battery may explode if installed incorrectly. Replace the battery only with the same or equivalent type. Discard used batteries according to the manufacturer’s instructions.

  • Page 40: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 41 Procedure Turn the system board over and place it on a flat surface. In sequential order (indicated on the heat sink), remove the screws that secure the heat sink to the system board. Lift the heat sink off the system board. heat sink screws (6) Removing the Heat Sink...

  • Page 42: Procedure

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Clean the thermal grease from the bottom of the heat sink and reapply it.
  • Page 43 7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.

  • Page 44: Procedure

    Procedure Turn the system board over and place it on a flat surface. Disconnect the fan cable from the system board. Remove the screw that secures the fan to the system board. Lift the fan off the system board. screw fan cable Removing the Fan...

  • Page 45: Procedure

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the screw hole on the fan with the screw hole on the system board.

  • Page 46: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 47 Remove the system board. See "Removing the System Board" on page 33. Note the speaker-cable routing and remove the cable from the routing guides on the computer base. Lift the speakers, along with the speaker cable, off the computer base. speaker cable routing speakers (2) Removing the Speakers...

  • Page 48: Procedure

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the speakers using the alignment posts and place the speakers on the computer base.

  • Page 49: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 50 Move the power-adapter port cable away from the screws on the display hinge. Remove the screws that secure the display assembly to the computer base. Lift the display assembly off the computer base. display assembly screws (3) power-adapter port cable Removing the Display Assembly...

  • Page 51: Procedure

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Place the display assembly on the computer base and align the screw holes on the display assembly with the screw holes on the computer base.

  • Page 52: Removing The Display Bezel

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.

  • Page 53: Procedure

    Procedure Press and lift the hinge covers to remove them from the display assembly. hinge covers (2) CAUTION: It is recommended to use fingertips to pry the display bezel, to avoid damaging the display panel. Using your fingertips, carefully pry up the inside edges of the display bezel. Lift the display bezel off the display back-cover.

  • Page 54: Postrequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the display bezel with the display back-cover and gently snap the display bezel into place.

  • Page 55: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 56 Procedure Remove the screws that secure the display hinges to the display back-cover. Lift the display hinges off the display back-cover. screws (8) display hinges (2) display back-cover Removing the Display Hinges...
  • Page 57 7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Align the screw holes on the display hinges with the screw holes on the display back-cover.

  • Page 58: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.
  • Page 59 Procedure Remove the screws that secure the display panel to the display back-cover. Gently lift the display panel and turn it over. display back-cover display panel screws (4) Removing the Display Panel...
  • Page 60 Peel off the tape that secures the display cable to the display panel. Disconnect the display cable from the display panel. display cable tape Removing the Display Panel...

  • Page 61: Postrequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Connect the display cable to the display panel.

  • Page 62: Prerequisites

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Prerequisites Remove the battery. See "Removing the Battery" on page 10.

  • Page 63: Procedure

    Procedure Remove the screw that secures the camera module to the display back-cover. Disconnect the camera cable from the camera module. Peel off the tape that secures the camera module to the display back-cover. Lift the camera module off the display back-cover. screw camera module tape...

  • Page 64: Procedure

    7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance. Procedure Place the camera module on the display back-cover.

  • Page 65: Flashing The Bios

    You may need to flash (update) the BIOS when an update is available or when you replace the system board. To flash the BIOS: Turn on the computer. Go to dell.com/support. If you have your computer's Service Tag, type your computer's Service Tag and click Submit.

This manual is also suitable for:

Inspiron 3521Inspiron 5537Inspiron 5521Inspiron 3537Inspiron 15Inspiron 15r

Table of Contents