Advertisement
Quick Links
OPERATING
iNSTRUCTIONS
AND
PARTS
L|ST
FOR
9 raNCH BENCH
SAVe/
Model
103.22181
MITER
PROTRACTOR
LOCK KNOB
FENCE
FENCE SLIDE BAR
CONTROL
KNOB
FIGURE
I
This
9-1nch Tilting
Arbor
Bench
Saw
will
produce
quality
work
satisfying
the
demands
of
the
most
exacting
craftsman.
To increase
the versatility
of this
saw beyond
the
normal
range
of Bench Saw operations,
various
ac-
cessories
are readily
available°
See Page 5o
To prevent damage
in shipping,
some of the parts
were
disassembled
from
the tool.
These
parts
are
listed below.
Be sure they are all accounted
for before
discarding
any of the packing
material.
1.
Fence; item
106.
2.
Miter
gage assembly;
item 114.
3.
Insert with
clips; items 15, 16 and
17o
4.
Motor
pulley;
item 66,
5.
V-belt;
item 64.
6.
Bag contains
10, 11, 12, 13, 19, 20, 23, 24, and
63.
7.
Fence Slide Bar; item 2.
ASSEMBLY:
Front Fence Bar
The front
fence
bar must be fastened
to the front
edge
of the saw
table
with
three
(3) slotted
head
screws,
No. 10, spacers, No. 11, lock washers,
Noo 12,
and hex nuts, No. 13. See Fig. 2.
Before
-tightening
the
screws
securely,
the
fence
bar
must be accurately
adjusted
to the 2t/32
dimen-
sion over
the entire
length.
INSTALLATION
OF TABLE INSERT:
The insert
in the saw has six tabs which
rest on the
ledge of the table insert opening°
FIGURE
2
FIGURE
3
Advertisement
Related Manuals for Craftsman 103.22181
Summary of Contents for Craftsman 103.22181
- Page 1 FIGURE This 9-1nch Tilting Arbor Bench will produce quality work satisfying demands most exacting craftsman. To increase the versatility of this saw beyond normal range of Bench Saw operations, various cessories are readily available° See Page 5o To prevent damage...
- Page 2 R P.M. motor will drive the saw at the recommended If the insert is not flush with the table top proceed as follows: speed - 3900 R.P°Mo 1+ Remove insert from table. LUBRICATION: Bend tabs slightly away from top side. 3_ Replace insert in+table+ The precision...
-
Page 3: Operation
The Mitre Gauge has been designed to assure RAISE BLADE maximum amount of accuracy, it has been adjusted 3 INCHES at the factory to give accurate 45 ° and 90 ° settings carefully packed to protect this fine setting DI_ANCE SHOULD shipment. - Page 4 ACCESSORIES: SAW GUARD --CATALOG No. 9-21046 TABLE EXTENSION- CATALOG No., 99-21047 TOOL STAND--CATALOG Nor 99-2228 POWER PAK -- CATALOG 9_2134 TABLE EXTENSION--CATALOG No. 99.2t78 ROLLER EXTENSION- CATALOG 9-22165. loci "-...
-
Page 5: Parts List
PARTS LiST Numbers when ordering Repair Parts, always Part Numbers, Part No, Name Dart No, Name ;53740 Base X-179 Set Scr° 5/16-18 x 5/16 Sac, Hd, Cup Point _53818 Fence Sffde Bar 8036.,B Motor Puffey with Set Scr _53742 Trim Panel 38666 Pivot Bearing Retaining... - Page 6 OPERATING INSTRUCTIONS AND PARTS LiST FOR CRAFTSMAN BENCH SAW 9 INCH MODEL NUMBER 103._.2181 The model number of your Bench Saw wilt be found on the front panel of the Saw_ Always mention this model number when communicating with us...