Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC MD242C2
Summary of Contents for NEC MD242C2
- Page 1 MD242C2 INSTALLATION & MAINTENANCE GUIDE...
-
Page 2: Table Of Contents
CAN/CSA-C22.2 NO.60950-1-07 45VU E332883 Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. -
Page 3: Power Cord
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. -
Page 4: Intended Use
The MD242C2 Color display is intended to be used for displaying and viewing of digital images for diagnosis by trained physicians. To guarantee the display performance as specifi ed, it must only be used in conjunction with NEC approved display controllers. MD242C2 cannot be used for a life-support system. -
Page 5: Registration Information
Declaration Declaration of the Manufacturer Declaration of the Manufacturer Means of Conformity NEC Display Solutions Europe GmbH declares that the product listed is in conformity with the essential requirements and Device Classifi cation: Class I, non-measuring function provisions of the Council Directive 93/42/EEC, including the Applicable Rules: Annex IX, Rules 1.4 (Section 1) -
Page 6: Recommended Use
WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: No modifi cation of this equipment is allowed. WARNING: For EMC details information, please contact NEC local authority. •... - Page 7 Get regular eye checkups. NOTE: This model is set up in the factory so that the NEC logo is briefl y displayed after the monitor is powered on. This feature can be turned on or off in the Advanced OSD.
-
Page 8: Contents
Contents Your new NEC monitor box* should contain the following: • MD242C2 monitor with tilt/swivel/pivot/height adjust stand • Power Cord • DVI-D cable • DisplayPort cable • USB Cable • Quick Reference Guide • CD-ROM x 2 • Screw (x 4) (to mount the monitor to a fl exible arm (page 11)) -
Page 9: Quick Start
Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” (page 4) before installation. In order to display the maximum resolution, a display controller that can output a resolution of 1920 x 1200 (in landscape mode) or 1200 x 1920 (in portrait mode) is needed. - Page 10 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a).
-
Page 11: Raise And Lower Monitor Screen
7. Slide down the cable cover (Figure D.1). 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NOTE: Please refer to the Caution section of this manual for proper selection of an AC power cord. Figure D.1 9. - Page 12 Screen Rotation Before rotating, the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your fi ngers. Disconnect all cables. To raise the screen, place hands on each side of the monitor and lift up to the highest position (Figure RL.1). To rotate the screen, place hands on each side of the monitor and turn clockwise from Landscape to Portrait or counter- clockwise from Portrait to Landscape (Figure R.1).
-
Page 13: Flexible Arm Installation
Flexible Arm Installation This LCD monitor is designed for use with a fl exible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the monitor mount. • To meet the safety requirements, the monitor must be mounted to an arm that supports the weight of the monitor. See page 26 for details. -
Page 14: Controls
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access the OSD menu, press the MENU button. The Key Guide appears pressing any button when not in the OSD control menu. NOTE: The OSD must be closed in order to change the signal input. 5. -
Page 15: Setting Osd Language
SETTING OSD LANGUAGE • Set the OSD language before using OSD functions. • Use the control keys (LEFT/RIGHT or UP/DOWN or EXIT) to access the “LANGUAGE SELECTION” menu. • Press the LEFT/RIGHT or UP/DOWN buttons to select the desired OSD language. •... -
Page 16: Picture Mode
AUTO FINE (Analog input only) This function automatically and periodically adjusts the “FINE” setting for change in signal condition. This function adjusts approximately every 33 minutes. EXPANSION Sets the zoom method. FULL: The image is expanded to full screen regardless of the resolution. ASPECT: The image is expanded without changing the aspect ratio. -
Page 17: English
VIDEO DETECT Selects the video detection method, when more than one video signal source is connected. FIRST: When current video input signal is not present, then the monitor searches for a video signal from a different video source. If a video signal is supplied by the other video source, the monitor automatically switches to the new video source. -
Page 18: Osd Color
OSD COLOR Adjusts the color of the OSD Menu. “Tag window frame color”, “Item select color” and “Adjust window frame color” can be changed to Red, Green, Blue, or Gray. FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings (LUMINANCE, IMAGE CONTROL, PICTURE MODE, SHARPNESS, OFF MODE, OSD LEFT/RIGHT, OSD UP/DOWN, OSD TURN OFF) back to the factory settings. -
Page 19: Using The Picture Mode Function
The conditions are optimal for viewing documents and sRGB images. PROGRAMMABLE1 For Hardware Calibration settings by NEC Display Solutions QA software (some OSD settings are disabled). NOTE: A “PICTURE MODE IS LOCKED” warning message appears when PICTURE MODE is locked out. -
Page 20: Quick Screen Qa Test Function
Quick screen QA test function Allows the monitor to display an internal test pattern similar to AAPM TG18-QC, without using an external signal source. A quick overall visual evaluation as well as an inspection of the gray levels according to DICOM is available with this built-in method. - If the monitor is connected with a video signal source (computer): Make sure that no OSD menu is displayed, then press the RESET button for more than 3 seconds or press the RESET button twice. -
Page 21: Advanced Osd
NEC Display Solutions QA Software. Used for DICOM calibration according to DICOM Part 14. This setting can be selected only by using the NEC Display Solutions software when PICTURE MODE is set to PROGRAMMABLE1. Not selectable on the Advanced menu. - Page 22 Adjusts color gamut. When the selected settings are outside of the LCD gamut, the GREEN indicator on the OSD will turn magenta. BLUE UNIFORMITY* This function electronically compensates the slight variations in the white uniformity level that may occur across the display area of the screen. These variations are a characteristic of LCD panel technology.
- Page 23 LONG CABLE R-H.POSITION: Adjusts the position of the red component of the image. Press “LEFT” or “RIGHT” to adjust. CAPABILITY G-H.POSITION: Adjusts the position of the green component of the image. (Analog input only) Press “LEFT” or “RIGHT” to adjust. B-H.POSITION: Adjusts the position of the blue component of the image.
- Page 24 Tag5 H.POSITION Controls the Horizontal Image Position within the display area of the LCD. Press “LEFT” or “RIGHT” to adjust. V.POSITION Controls the Vertical Image Position within the display area of the LCD. Press “LEFT” or “RIGHT” to adjust. H.SIZE Adjusts the horizontal size of the screen.
- Page 25 POWER Sets the power saving mode. MANAGEMENT HUMAN SENSING: HUMAN SENSING has three settings: OFF: No human sensing. DEEP: After it is detected that there is no person, the monitor shifts to power saving mode automatically. When a person comes near the monitor again, it resumes from the power saving mode and displays the images.
- Page 26 BOOT LOGO The NEC logo is briefl y displayed after the monitor is powered on. This feature can be turned on or off in the OSD. Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGO menu will appear.
- Page 27 GRAYSCALE MODE This function changes the display image to monochrome. There are 4 types of settings. OFF: The Display Image is COLOR. MODE1: The signal Input is 8 bit monochrome. The display shows a grayscale image. This mode uses only the Green channel of an R/G/B input signal. MODE2: Input is R/G/B Color, but the monitor changes the color space to YUV.
-
Page 28: Specifi Cations
60 Hz to 85 Hz 1280 x 1024* at 60 Hz to 85 Hz 1600 x 1200* at 60 Hz NEC DISPLAY SOLUTIONS recommended resolution 1920 x 1200* at 60 Hz......... for optimal display performance. 1400 x 1050* at 60 Hz to 75 Hz... -
Page 29: Features
Features DisplayPort: DisplayPort is designed to be the future-ready, scalable solution for high performance digital display connectivity. It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables. DVI-D: The digital-only subset of DVI ratifi ed by the Digital Display Working Group (DDWG) for digital connections between computers and displays. -
Page 30: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 31: Stand-Alone Calibration
STAND-ALONE CALIBRATION Stand alone calibration can recalibrate the display without using a computer by the integrated front sensor or connecting an external sensor. There are 4 functions in STAND-ALONE CALIBRATION. • Self Calibration: Manually adjust the integrated front sensor with an external near range color analyzer reference, which is traceable to a primary standards laboratory. -
Page 32: Self Calibration
Self Calibration Manually adjust the integrated front sensor with an external near range color analyzer reference, which is traceable to a primary standards laboratory. All PICTURE MODES are updated when Self Calibration is performed. NOTE: An external near range color analyzer, which is traceable to a primary standards laboratory, is required. 1. -
Page 33: Gamma Adjust
Gamma Adjust By using the integrated front sensor, Gamma Adjust recalibrates the LCD gamma. Gamma Adjust is recommended if MAX GSDF ERROR exceeds the medical standards. All PICTURE MODES are updated when Gamma Adjust is performed. 1. To show the CALIBRATION menu, select the STAND ALONE CALIBRATION in the advanced menu (page 25). 2. -
Page 34: Dicom Measurement
DICOM Measurement DICOM PART14 can be performed by using the integrated front sensor. 1. To show the CALIBRATION menu, select the STAND ALONE CALIBRATION in the advanced menu (page 25). 2. Use “LEFT” or “RIGHT” to select DICOM MEASURE in the MODE selection (Figure D.1). 3. - Page 35 5. Input the value measured at 1, and press SELECT (Figure AS.3). When not having measured, press SELECT without changing the value. 6. After the CALIBRATION SUCCEEDED message appears (Figure AS.4), press SELECT. You can set DATE and TIME by using control keys, and press SELECT. 7.
-
Page 36: Manufacturer's Recycling And Energy Information
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.