Advertisement
Quick Links
LED Road Light Kit
ProLine H600 Rotary Mower
Model No. 31046
Installation
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface, engage the
parking brake, lower the cutting unit, shut off the
engine, and remove the key.
2.
Disconnect the battery; refer to the electrical
system maintenance section of your Operator's
Manual.
WARNING
Using a drill without wearing eye
protection may allow debris to enter the
eye, causing personal injury.
When drilling, always wear eye
protection.
© 2024—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Installing the Rear Lights
Parts needed for this procedure:
Procedure
Register at www.Toro.com.
2
2
Rear taillight
1
Rear light plate
4
Set screw (M5 x 30 mm)
4
Washer (3/16 inch)
4
Locknut (M5)
1
Plate-number light
2
Screw
2
Washer
2
Nut
5
Hex-head bolt (M5 x 14 mm)
5
Washer
7
Washer
7
Nut
2
Hopper relfelector
1.
Install the 2 rear taillights to the rear light-plate
with 4 set screws (M5 x 30 mm), 4 washers (3/16
inch), and 4 locknuts (M5); refer to
2.
Install the plate-number light to the rear light
plate with 2 screws, 2 washers, and 2 nuts.
3.
Route the plate-number light connector behind
the rear light plate.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3463-494 Rev B
Installation Instructions
Figure
*3463-494*
1.
Advertisement
Related Manuals for Toro 31046
Summary of Contents for Toro 31046
- Page 1 Form No. 3463-494 Rev B LED Road Light Kit ProLine H600 Rotary Mower Model No. 31046 Installation Instructions Installation Installing the Rear Lights Preparing the Machine Parts needed for this procedure: Rear taillight Rear light plate No Parts Required Set screw (M5 x 30 mm)
- Page 2 g466554 Figure 1 1. Set screws (M5 x 30 mm) 6. Washers 2. Washers (3/16 inch) 7. Nuts 3. Locknuts (M5) 8. Plate-number light 9. Rear light-plate 4. Screws 5. Taillight Using the rear light plate as a template, mark and drill 5 mm holes into the rear hopper door (Figure g466553...
- Page 3 g466555 Figure 3 1. Nut 4. Washers (3/16 x 1/2 inch) 7. Washer 2. Washer 5. Washer 8. Hex-head bolt (M5 x 14 mm) 3. Locknut (M5) 6. Hex-head bolt (M5 x 14 mm)
- Page 4 Using Figure 4, measure and mark the location for drilling the hopper reflector holes. Drill a hole (5 mm) at each location (Figure g482195 Figure 5 1. Nut 3. Hopper reflector 2. Washer Installing the Front Lights g482120 Figure 4 Parts needed for this procedure: 1.
- Page 5 Install the horn to the left light arm with a screw, Install the mirror to the left light arm with 2 washer (M8), and nut (Figure screws and 2 washers (Figure Install the left light marked “LH” to the left light arm with the screw, washer, and nut supplied with the light.
- Page 6 Install the clamp to the console clamp with a screw, 2 wahsers, and a nut. Install the clamp to the console clamp with a screw, 2 wahsers, and a nut (Figure Installing the Switch Mount Loosely install console plate around the steering column using the console clamp, 2 plastic rivets, 4 carriage bolts (M6 X 45 mm), 4 washers, and Parts needed for this procedure:...
- Page 7 g466557 Figure 7 22. Washer 1. Control cover 8. Multi-function switch 15. Clip (1/4-20) 23. Hex-head bolt 2. Clamp 9. High/Low beam switch 16. Pan-head screw (M4 x 12 3. Screw 10. Gasket 17. Switch support 24. Plastic rivet 4. Relay 11.
- Page 8 Routing the Wire Harness Parts needed for this procedure: Wire harness Cable ties Procedure Refer to the following figures and instructions for routing the wire harness. Connect the power adaptor to PLH600 machine wire harness below fuse box (Figure g466041 Figure 8 1.
- Page 9 Feed the left and right front light wires and the console wires from road-light harness through the clamp (Figure g466052 Figure 9 1. Clamp Connect road-light harness to the left and right front light connector. Secure the wires with cable ties to foot panel brace (Figure 10 Figure...
- Page 10 g466062 Figure 11 1. Cable ties Feed the console wire from the road-light harness through platform and rear to the steering column (Figure 12). g466063 Figure 12 1. Platform hole 2. Steering column hole...
- Page 11 Connect the 12-way pin to console wire assembly (per electrical schematic) and connect it to the console assembly (Figure 13). g466064 Figure 13 Connect the 2-way pin road-light wire harness to machine harness (Figure 14). g466065 Figure 14 1. Connector...
- Page 12 Feed the solenoid cable below the throttle assembly and fasten it to the bracket using a screw, washer, and a nut (Figure 15). g466066 Figure 15 1. Solenoid cable g466067 Figure 16 1. Solenoid cable fastened...
- Page 13 Connect the fuse box by removing plastic cover and feed the fuse box from the bottom of the bracket. Secure the plastic cover on the fuse box and fasten it to the bracket with the 2 existing screws (Figure 17). g466042 Figure 17 Use 2 cable ties to secure the front section of the wire harness...
- Page 14 Remove the engine cover plate and route harness for the rear lights below the seat. Secure the harness to the chassis membrane using 4 cable ties as shown in Figure g466044 Figure 19...
- Page 15 Connect the 5-way connector (per the schematic) to rear light wiring harness assembly (Figure 20). g466045 Figure 20 1. Connector...
- Page 16 Route the rear-light harness through the rear frame and the hopper frame. Use 9 cable ties to secure the harness as shown in Figure 21 Figure g466046 Figure 21 1. Cable tie g466047 Figure 22 1. Cable tie...
- Page 17 Drill a 21 mm hole from the bottom of the hopper and feed the wire harness through the cable-fitting nut. Secure the cable fitting with the cable fitting nut (Figure 23). g466048 Figure 23 1. Drill a 21 mm hole 2.
- Page 18 Secure the rear-light wire harness to PLH600 machine wire harness with a cable tie and route the harness through 2 clamps on the front of the hopper. g466049 Figure 24 1. Clamp 2. Cable tie...
- Page 19 Remove the hopper screen from the machine (Figure 25). g467457 Figure 25 1. Hopper screen Remove the 4 nuts, 8 washers and 4 screws holding the chain to the plastic grass-catcher panel (Figure 26). g466050 Figure 26 1. Bolts, washers, and nuts 2.
- Page 20 Remove the 2 nuts, 4 washers, and 2 screws from the right removable-grid slide (Figure 28). g466053 Figure 28 1. Screws, washers, and nuts Remove the 2 nuts, 3 washers, 1 washer (M8) and 2 screws from the right removable-grid slide (Figure 29).
- Page 21 Install the hopper grid assembly and route the harness through the two clamps on the hopper frame and the hopper door frame (Figure 31 Figure 32). g466056 Figure 31 1. Clamp g466057 Figure 32 1. Clamp...
- Page 22 Connect the rear-lights wire assembly to the harness and secure it using a cable tie to hopper door grid. g466058 Figure 33 1. Hopper door grid Checking the Lights No Parts Required Procedure Refer to the following figures and instructions for routing the control wire harness.
- Page 23 Connecting the Battery No Parts Required Procedure Connect the battery; refer to the electrical system maintenance section of your Operator’s Manual. Operation Operating the Lights g466060 The light controls on the control panel are marked with Figure 35 the symbols shown below: 1.
- Page 24 To switch the beacon on, push the top of the beacon switch Maintenance • Replace all worn or damaged parts with genuine Toro parts. • Periodically check that all lights are working. • Ensure that the headlights are adjusted correctly.
- Page 25 Schematic g467532 Figure 36...
- Page 26 g467533 Figure 37...
- Page 27 Notes:...