Advertisement
Quick Links
Advertisement
Related Manuals for Toro RX2
Summary of Contents for Toro RX2
- Page 1 Ra g e A m p l i f i e r RX4/RX4S R2/R3/R4/R5/R6 RAGE COMPACT CLASS AB/D AMPLIFIER Owners Manual Please read through this manual to familiarize yourself with your new amplifier. Should your TORO AUDIO mobile amplifier ever require service, you will need to have the original dated receipt.
- Page 2 Thank you and Congratulations Thank you for your decision to purchase a TORO AUDIO Rage amplifier! Our Rage amplifiers are the result of extensive engineering, testing, and bullet proof construction. Their versatility enables compatibility with optional signal and audio processors. These high quality MOSFET amplifiers may be configured to allow maximum flexibility in designing different speaker and subwoofer options.
-
Page 3: Technical Features
MECP installer. This Owners Manual only provides general installation and operation instructions. If you have any reservations about your installation skills, please contact your local TORO AUDIO dealer for assistance. IMPORTANT: This amplifier is designed for operation in vehicles with 12-Volt negative ground electrical systems only. - Page 4 If possible, use tubing through grommets Fig.1 Mounting Amplifier Due to the high-power output of the TORO AUDIO RAGE amplifiers, considerable heat may be produced when the unit is in operation. For this reason, the amplifier should be mounted in a location which will allow air to circulate freely.
- Page 5 The floor of the trunk, under the driver's seat, or on the back of the rear seat. For alternate installation locations, please consult your authorized TORO AUDIO Dealer. NOTE: Do not use a drill with driver bit to mount the amplifier. Excessive force could cause the plastic mounting feet to crack.
- Page 6 FIG2 . MONO AMPLIFIER PANEL LAYOUT PWR/PRO 10V 0.2 DESIGNED & ENGINEERED IN U.S.A. FUSE DESIGNED & ENGINEERED IN U.S.A. PWR/PRO BASS CONTROL BOOST 10V 0.2 12dB WIDE NARROW DESIGNED & ENGINEERED IN U.S.A. R3/R4/R5/R6 R3/R4/R5/R6...
-
Page 7: Amplifier Functions
FIG3 . 4-CH AMPLIFIER PANEL LAYOUT REAR PWR/PRO X-OVER Full /HiPass Low/ BandPass 10V 0.2 10V 0.2 Full 3KHz 3KHz DESIGNED & ENGINEERED IN U.S.A. RX4S bridged FUSE DESIGNED & ENGINEERED IN U.S.A. RX4S FIG4. 2-CH AMPLIFIER PANEL LAYOUT PWR/PRO 10V 0.2 DESIGNED &... - Page 8 4.GND CONNECT THIS CABLE DIRECTLY TO THE FRAME OF THE VEHICLE. MAKE SURE THE METAL FRAME HAS BEEN STRIPPED OF ALL PAINT DOWN TO THE BARE METAL. USE THE SHORTEST DISTANCE POSSIBLE. IT IS ALWAYS A GOOD IDEA TO REPLACE THE FACTORY GROUND AT THIS TIME WITH A LARGER CABLE EQUAL TO THE NEW DIRECTLY TO THE VEHICLE BATTERY GROUND TERMINAL OR ANY OTHER FACTORY GROUND POINTS.
- Page 9 VERSATILE BANDPASS SET UP FROM 20HZ TO 3KHZ OR SIMPLY A LOW PASS SET UP FOR SUBWOOFERS WITH SUB SONIC CONTROL. TORO AUDIO Rage Mono Block amplifiers will draw large levels of current, so use the largest gauge power / ground cable possible. Using too small of a power cable can result in unnecessary over-heating of the amplifier, distortion at high volume levels and might even cause the thermal protection circuitry to shut-off...
- Page 10 12V(Power) This amplifier should be wired directly to the vehicle battery using the appropriate size cable. Start at the vehicle battery and run the power cable through to the amplifier. Avoid running the power cable over engine components and near heater cores. The use of an in-line fuse or circuit breaker is a must;...
- Page 11 REM on the amplifier FUSE REQUIREMENTS While the panel on your TORO AUDIO amplifier incorporates one or more fuses, these do nothing to protect the vehicle from a dangerous short circuit. It is absolutely vital that the main power lead to the amplifier(s)in the system be fused within 18-inches(45cm) of the connection to the vehicle battery.
- Page 12 PWR/PRO 10V 0.2 DESIGNED & ENGINEERED IN U.S.A. 4 BRIDGED FUSE DESIGNED & ENGINEERED IN U.S.A. 2-4 OHM 2-4 OHM FIG6. Low Level Input using RCA Choose the correct length and style of RCA interconnects for your needs. Always use high quality RCA audio cables (not supplied) for signal connections--those with multiple layers of shielding or a twisted pair variety provides better noise rejection.
-
Page 13: Wiring Diagram
WIRING DIAGRAM FIG7. MONO AMPLIFIER WIRING (SINGLE WOOFER LOAD) R3/R4/R5/R6 PWR/PRO BASS CONTROL BOOST 10V 0.2 12dB WIDE NARROW DESIGNED & ENGINEERED IN U.S.A. R3/R4/R5/R6 FUSE DESIGNED & ENGINEERED IN U.S.A. 2 OHM MINIMUM PWR/PRO 10V 0.2 DESIGNED & ENGINEERED IN U.S.A. - Page 14 FIG8. MONO AMPLIFIER WIRING (MULTI-WOOFER LOAD) R3/R4/R5/R6 4 OHM 4 OHM Two DUAL 4-Ohm SUB PWR/PRO BASS CONTROL BOOST 10V 0.2 12dB WIDE NARROW DESIGNED & ENGINEERED IN U.S.A. R3/R4/R5/R6 *EQUIVALENT PARALLEL WOOFER LOADS CANNOT BE LESS THAN THE MINIMUM STABLE LOAD RATED IN THIS MANUAL.
- Page 15 FIG9. RX2 AMPLIFIER WIRING (1-CHANNEL MODE) 4 BRIDGED FUSE DESIGNED & ENGINEERED IN U.S.A. MINIMUM IMPEDANCE FOR BRIDGED INSTALLATION IS 4-OHM PWR/PRO 10V 0.2 DESIGNED & ENGINEERED IN U.S.A. FIG10. RX2 AMPLIFIER WIRING (2-CHANNEL MODE) 4 BRIDGED FUSE DESIGNED & ENGINEERED IN U.S.A.
- Page 16 FIG11. RX4/RX4S AMPLIFIER WIRING (3-CHANNEL MODE) bridged FUSE DESIGNED & ENGINEERED IN U.S.A. REAR PWR/PRO X-OVER Full /HiPass Low/ BandPass 10V 0.2 10V 0.2 Full 3KHz 3KHz DESIGNED & ENGINEERED IN U.S.A.
- Page 17 FIG12. RX4/RX4S AMPLIFIER WIRING (4-CHANNEL MODE) bridged FUSE DESIGNED & ENGINEERED IN U.S.A. REAR PWR/PRO X-OVER Full /HiPass Low/ BandPass 10V 0.2 10V 0.2 Full 3KHz 3KHz DESIGNED & ENGINEERED IN U.S.A.
-
Page 18: Troubleshooting
NOTE: If the Status LED is activated and glows RED with no speakers connected to the amplifier, and all the power connections are correct, this would indicate an internal problem with the amplifier. Contact TORO AUDIO USA or your local dealer. - Page 20 TORO AUDIO Amplifiers are to be free of defects in material and workmanship for a period of one(1)year. TORO AUDIO Amplifiers are to be free of defects in material and workmanship for a period of 90 days, from the date of purchase, if purchased over the counter from an authorized TORO AUDIO retailer. The Warranty will increase to 1 (one) year if installed by a TORO AUDIO Authorized Installer.
- Page 21 WWW.TOROAUDIO.COM MANUFACTURED BY TORO TECH LLC. DESIGNED IN U.S.A.