Page 2
Service Guide Version and Revision Version Date Revision History Customer Name TPV Model Name AT3247 E329G2NBWAZE2N Aug.-18-09 Initial release AT3248 E329G2NBWAZF2N...
Page 3
Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Page 4
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines. Warning: (For FCC Certified Models) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 5
Precautions Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
Table of Contents Monitor Features ……………………………………… General Specifications ……………………………………… LCD TV Description ……………………………………… Precautions And Notices ……………………………………… D-SUB PIN Distribution ……………………………………… Chapter 1 Factory Preset Display Modes ……………………………………… LCD TV Panel Specification ……………………………………… Panel Features ……………………………………… General Specifications ……………………………………… Mechanical Specifications ………………………………………...
LCD TV Description The LCD TV will contain a main board (include audio), a switching power board, a function keyboard, an IR Board and a side board. The main board and power board will house the flat panel to control logic I2C bus, DDC, brightness control logic for LCD panel, DC-DC conversion to supply the appropriate power to the whole board and transmitting TTL level signals into LCD Module to drive the LCD display circuit.
D-SUB PIN Distribution This procedure gives you instructions for installing and using the LCD TV display. (1) Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduct ground.
LCD TV Panel Specification The LC320WXE is a Color Active Matrix Liquid Crystal Display with an integral External Electrode Fluorescent Lamp(EEFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a 31.51 inch diagonally measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array).
Chapter 3 Remote Control & OSD Operating instructions Using the Remote Control 5 e (Empowering Technology) Press to activate Acer Empowering Technology. 6 MENU Press to open or close the Menu. 7 Back Press to back to previous Menu. 8 Directional keys/OK...
Page 16
Teletext 1 Color buttons (R/G/Y/B) Operates corresponding button on the teletext page. 2 INDEX Press to go to the index page. 3 SUBTITLE Press to view subtitles on the screen. 4 REVEAL Press to reveal hidden teletext information. 5 SUBPAGE Press to access the teletext’s subpages directly.
Logo When the monitor is power on, the LOGO will be showed in the center, and disappear slowly. How to Optimize The DOS-Mode Plug And Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
Chapter 4 Machine Disassembly This chapter contains step-by-step procedures on how to disassemble the monitor for maintenance. The tools listed as below are that we may use during this procedure: 1. A proper screwdriver 2. A pair of glove 3. A pliers 4.
Page 27
Disassemble the back cover 1. Remove 11 screws to remove back cover. 2. Pry the monitor up then find out the hooks’ position, use the tool (like the picture or other card) to insert into the gap of bezel and rear cover.
Page 28
3.Turn over the monitor and take off the rear cover.
Page 29
Disassemble the speakers. to r Remove the 2 screws marked in red and disconnected the connector remark in green emove the speakers Key board Main board Power board The speakers Remove the key board. Disconnected the connector remark in green to remove the key board.
Page 30
Remove the main board, power board. 1.Remove the 5 screws marked in red and disconnected the connector remark in green to remover the main board. 2.Remove the 6 screws marked in red and disconnected the connector remark in green to remove the main board...
Page 31
Remove the bezel. 1.Remove the 12 screws marked in red to remove the BKT.
Page 32
Remove the IR board. Remove the 2 screws marked in red . The panel...
Chapter 5 Trouble Shooting No picture (LED orange) No picture Check key board/IR board Change key board/IR board Check 24V power supply Check the power supply circuit Check main board Standby power supply Change U152 Check U400 Change U400 Check I C bus Check I C communication...
Page 34
Abnormal display Reset source Check the source Check signal filter circuit Replace the filter or resistance RF signal Check TV system setup Check input Check LVDS cable Replace LVDS cable Check Tuner Check panel Replace panel Replace Tuner No sound Reset source Check the source Check if mute...
Page 35
No Power (No LED indicator) Plug in power cord and interface Check power cord and board interface Replace F901 or BD901 or C907 Check F901, BD901, C907 Check IC903, Q903 Replace IC903 or Q903 Replace T901 Check T901 Check D950, C953, C954 Replace D950 or C953 or C954...
Page 36
Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Replace Button Switch Is Button Switch normally? Is Key Pad Board Normally? Replace Key Pad Board Check Main Board...
Chapter 6 Upgrade Firmware 1.U390 FW update We must update U390 first, because the U390 firmware is the base of the system. When we update U390,the soft tool is MTK Tool, the hardware tool is 715T080-A To PC To TV 3 pin Software tool Version : mtk_tool-2.47.02.12_2 Hardware tool...
Page 38
Step 3: After we click upgrade, there will be a small window, we must select Flash Type. The correct type is NOR , Click OK . Step 4 :When we see this picture, show program OK ,then AC ON/OFF, program finished. 2.
Chapter 7 White-Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. YPbPr Mode display adjustment White balance adjustment (B) General set-up : Equipment Requirements: Minolta CA-110 or Equivalent Color analyzer Quantum Data Pattern Generator 802G , 802BT or equivalent instrument Input requirements: Input Signal Type : YPbPr signal 1.
Page 40
Color temperature Standard/Warm/Cold (x, y) co-ordinates specification: Picture Mode Normal (10000 0.281±0.005 0.288±0.005 Warm (8000 0.295±0.005 0.305±0.005 Cold (13000 0.269±0.005 0.274±0.005 Table: Reading with Minolta CA-110. Note: 1. Use Minolta CA-110 for color coordinates and luminance check. 2. Luminance > 400 cd/m in the center of the screen when Brightness control at 100;...
Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.